Avr development board atmega16

With this board you can develop and prototype with ATMEGA16/ATMEGA pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters.   FEATURES AVR Development Board for Atmel ATMEGA ISP Socket for Flashing On board Regulated Power Supply 5v,12v supplys Easy to test with Burg Connecters wires An RS232 Serial Port 7Seg Mulitplexed Display DC Power Supply Connector(12v Ac or Dc) READY INTERFACE For LCD display 2linex16Character 24Cxx (I2C) (EEPROM) RTC (DS LED array Matrix Key Pad 4 Interrupt Switches +12v Relay (one) Package Content   AVR Development Board (WITH CHIP MAX232) Burg Connecters 20 Nos Female to Female.

See our ratings Add this shop to my favorites ATtiny13 AVR Development Board Core Board Minimum System ₹ Availability:

Universal Development Board for Arduino, , PIC, AVR and ARM7, Raspburry Pi   (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL       Product Overview   1.     About Digital and Analog IO Interfacing Board                                                                    If you are learning any microcontroller than input and output circuit is always important to experiment with any microcontroller. Digital and Analog IO Board is suitable for quick experiment with any microcontroller.   2.     Features Digital and Analog IO Interfacing Board having a following features:                                                               ·          Eight LEDs ·          Four Switches ·          One LDR (Light Dependent Resistor) (Light Sensor) ·          One Temperature Sensor (LM35) (Sensor) ·          One Variable Resistor (Preset/POT) (Sensor) ·          One Infrared receiver (TSOP) (Remote Control Sensor) ·          One Buzzer ·          One Relay Categories into Inputs/Outputs 1.        Digital Inputs ·          Switches ·          Infrared receiver (TSOP.        Analog Inputs ·          Variable Resistor ·          LDR ·          Temperature Sensor 3.       Digital and Analog Outputs ·          LEDs ·          Buzzer ·          Relay Dimensions (LxWxH) - Cms: 6.5 CM X 6.5CM Datasheet:  http://www.mediafire.com/view/6c3dmdhpw3rlwdh/Digital_and_Analog_IO_Board.pdf

Introduction AVR CRUX is a tiny microcontroller development board based on ATtiny85, similar to the Arduino line, only cheaper, compact, lower power consumption and a bit less powerful. The board supports use of specific Arduino IDE and conveniently uses Arduino syntax for programming. This is a great way to jump into electronics and also perfectly fits when an Arduino is too big. AVR CRUX board may be tiny, but don’t be fooled by its size. The board has digital IO pins for regular use, PWM outputs to control motors and actuators, Analog inputs to interface with your sensors and a USB port to program and interact with your computer. It even has a tiny button switch used as reset button or a custom button and a user controllable LED to play around and create your first “blinking LED” program. A powerful board intended for artists, designers, hobbyists and anyone interested

    Other Items Feedbacks About Us Contact Us Add To Favorites   Set of 5 Pcs AVR28 Base Board  Kit.  For Electronic project.   CNB009 - Development Board For ATmega8,168,328,5 Pc Kit Electronics DIY Projects Atmel AVR - 28 Pin Base Boar d  -  1 Pcs (For ATmega8 ,ATmega 168,ATmega 328 Microcontroller)  **FREE**    10 Wire FRC Cable -  3 Pcs **FREE**    12V 1Amp SMPS -  1 Pc ** Does not Include Any Microcontroller ** ****FREE**** 3 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm.   ,with female connectors on both ends. Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

FREE USB CABLE + & AVR USB ISP Programmer (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL     Product Overview   1.     About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

1.      About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

Set of 4 Pcs AVR40 Base Board  Kit.  For Electronic project.  Atmel AVR - 40 Pin Base Boar d (For ATmega16, AT mega 32,Microcontroller) 1 Pcs 6 Digital Sensors Board for Line Follower    1 Pc 16X2 LCD Board for Display 1 Pc L298N Dual H-Bridge Motor Driver Board. **FREE**4 Pcs FRC Cable. ** Does not Include Any Microcontroller ** Atmel AVR - 40 Pin Base Board AVR-40Pin Development Board -For 40 pin AVR like ATMEGA16, ATMEGA32 etc it Comes without   micocontroller 1 Pc L298N Dual H-Bridge Motor Driver Board. 6 Digital IR - Photodiode Sensors Array for LFR Robot 6 IR-Photodiode Sensors Array- for Line following robot (LFR) and micro-mouse robot  (Digital out, Independent Manual Adjustable) Ideal for LFR (line-follower Robot) obstacles avoiding robots obstacles chasing robot side wall sensor maze solving robots 16x2 LCD Display Board Box Header Connection > LCD Connection (4Bit Mode) Pin#1   > RS(4) Pin#2   > EN(6) Pin#3   > D4(11) Pin#4   > D5(12) Pin#5   > D6(13) Pin#6   > D7(14) Pin#7   > No Connection Pin#8   > No Connection Pin#9   > Gnd () Pin#10 > +5V (2) Note Pin#5 of LCD (RW) is forcefully connected to Ground L298N Dual H-Bridge Motor Driver Board New Improved L298 Dual H-Bridge Board - Ideal for robot motor control, smart  full feature,compact, Compatible with AVR - 40 Board 10 Pin Box Header Connection Description Pin1= ENABLE B Pin2= ENABLE A Pin3= INPUT-3 Pin4= INPUT-1 Pin5= INPUT-4 Pin6= INPUT-2 Pin7= NOT CONNECTED Pin8= NOT CONNECTED Pin9= Ground Pin10=Vcc +5Volt    Fore More Details please refer Datasheet of L298N. ****FREE**** 4 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm. ,with female connectors on both ends. Please Clear Any Doubts "BEFORE" Buying any products form us. Fast Shipping via*      * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post. Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                                                        For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline: Powered by Turbo Lister

Description: Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two Two on-board relay which can switch up to 7Amps. Relays terminals (COM, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free-wheeling diode which will further protect your microcontroller from relay kick back. This is a 5V 2-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.    Features: 1.     Equipped with high-current relay 7A@250VAC / 10A@24VDC.  2.     It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. 3.     High quality screw terminals (Terminal Block) provided (COM, NC, NO) for quick and easy connection. 4.     Free wheeling diode to protect your microcontroller. 5.     Input Signal Pin connected to Burg stick for easy accessibility. 6.     LED Status indicators to indicate the relay ON/OFF status. 7.     Mounting holes provided. Package Contains: 1.      1 x Two channel 5V relay Module.    

About: Have a Micro-controller and a development board(Arduino, Freeduino, , AVR or PIC), But having a hard time with no components OR finding components? Right here! is the solution.  This "Micro-controller components kit" includes all the components needed to learn all the basics about the micro-controller you have. NOTE:  This kit does NOT include any Development Board, Instead it has components needed to learn about micro-controllers.  Package includes: Product Quantity 01.  Battery snap .  DC jack(9V) .  B read-board(Medium sized with 640 tie-in Points) .  Motor w/ Fan 01 each 05.  Potentiometer(pot - 22kOhm) .  Capacitors(100uF, 22uF, 10uF and 1uF) 05 each 07.  LED's(White, Red, Green and Blue) 05 each 08.  IR pai r(IR-Emitter and IR-Sensor) 02 each 09.  7-segment display .  Push buttons    .  Transistors(BC547 and BC each 12.  LDR(Light Dependent Resistor - also called Photo-resistor) .  Regulator( and LM each 14.  Resistance box(all standard values - Upto 20 different values)     01 box 15.  LCD display(16x.  F-F wires(4 different colors) 05 each 17.  Single strand wires(5 different colors) 03 each

9% Discount 31st March coupon code:  COUPONDUN9 1.     About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

Package Contents 1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has one (1) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free wheeling diode which will further protect your microcontroller from relay kick back. This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Free wheeling diode to protect your microcontroller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four (4) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has 2 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided