Controlled board lights

Description Single Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has ONE relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a Single channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description Four Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has FOUR relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a 4 channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Application: RF Controlled Robot Using RF Encoder and Decoder Module: Robosoft Labs RF Encoder & Decoder Interfacing board with HT12D & HT12E IC chips. Features: Easy interfacing with the RF modules, using the female headers for placing the modules. Breakout pins for connecting to the microcontroller. switch for manual Testing Status LED and switch button. Small size, high quality PCB.  Package Contents: 1 piece of RF encoder and decoder board with HT12E/HT12D IC chips. Applications: 1) RF Controlled Robot Using RF Encoder and Decoder Module: Robosoft Labs 2) Home Automation 3) Switch On/Off lights and other home appliances through with RF

New Improved 4 Channel IR Remote Control Board (Ideal for DIY Projects,Home/Office Automation) ** Firmware IC (IR-4 8PIN-DIP Check Circuit)  with IR  Remote Control (battery included) and IR receiver is available for Rs.275(Free Shipping) ***.       Have any queries, Please contact through by clicking "Ask seller a question" Applications: Applications include Garage door controllers, Car door controllers,Robotics Control switching of lights & fans (on & off) at homes, offices, shops, hotels by remote. Switching motors on & off. IR remote control projects Can easily replace switches with IR remote Features: Brand New and High Quality Restore Last Relay Position when Power   Relay contacts are brought out as Screw Terminal Each relays can Switch ON or OFF individually Can be used directly to control 240V power appliances Perfect for switching 240V appliances like Lights, Fans, etc remotely using IR remote. Receiver operates from 12V AC or DC power supply (not included) High Quality PCB that can easily be mounted inside regular switchboard   ON/OFF by using single button   Remote control Key1    -> Relay 1 ON/OFF   Remote control Key2    -> Relay 2 ON/OFF   Remote control Key3    -> Relay 3 ON/OFF   Remote control Key4    -> Relay 4 ON/OFF   Remote control MUTE  -> ALL Relay OFF   Remote control PLAY   -> ALL Relay ON   Remote control VOL+   -> Enable Buzzer   Remote control VOL -   -> Disable Buzzer ** Programmed Receiver IC (IR-4 8PIN DIP) with IR  Remote Control (battery included) available for Rs.275(Free Shipping) ***.       Have any queries, Please contact through by clicking "Ask seller a question" Package Contents: 1 x 4 Channel IR Relay Board 1 x Remote Control (battery included)

New Improved 4 Channel IR Remote Control Board (Ideal for DIY Projects,Home/Office Automation) ** Firmware IC (IR-4 8PIN-DIP Check Circuit)  with IR  Remote Control (battery included) and IR receiver is available for Rs.275(Free Shipping) ***.       Have any queries, Please contact through by clicking "Ask seller a question" Applications: Applications include Garage door controllers, Car door controllers,Robotics Control switching of lights & fans (on & off) at homes, offices, shops, hotels by remote. Switching motors on & off. IR remote control projects Can easily replace switches with IR remote Features: Brand New and High Quality Restore Last Relay Position when Power   Relay contacts are brought out as Screw Terminal Each relays can Switch ON or OFF individually Can be used directly to control 240V power appliances Perfect for switching 240V appliances like Lights, Fans, etc remotely using IR remote. Receiver operates from 12V AC or DC power supply (not included) High Quality PCB that can easily be mounted inside regular switchboard   ON/OFF by using single button   Remote control Key1    -> Relay 1 ON/OFF   Remote control Key2    -> Relay 2 ON/OFF   Remote control Key3    -> Relay 3 ON/OFF   Remote control Key4    -> Relay 4 ON/OFF   Remote control MUTE  -> ALL Relay OFF   Remote control PLAY   -> ALL Relay ON   Remote control VOL+   -> Enable Buzzer   Remote control VOL -   -> Disable Buzzer ** Programmed Receiver IC (IR-4 8PIN DIP) with IR  Remote Control (battery included) available for Rs.275(Free Shipping) ***.       Have any queries, Please contact through by clicking "Ask seller a question" Package Contents: 1 x 4 Channel IR Relay Board 1 x Remote Control (as per new shipping policy from FedEx battery cannot include for power ship orders, all non power ship orders battery included)

Package Contents 1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has one (1) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free wheeling diode which will further protect your microcontroller from relay kick back. This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Free wheeling diode to protect your microcontroller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four (4) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has 2 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Description: Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two Two on-board relay which can switch up to 7Amps. Relays terminals (COM, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free-wheeling diode which will further protect your microcontroller from relay kick back. This is a 5V 2-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.    Features: 1.     Equipped with high-current relay 7A@250VAC / 10A@24VDC.  2.     It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. 3.     High quality screw terminals (Terminal Block) provided (COM, NC, NO) for quick and easy connection. 4.     Free wheeling diode to protect your microcontroller. 5.     Input Signal Pin connected to Burg stick for easy accessibility. 6.     LED Status indicators to indicate the relay ON/OFF status. 7.     Mounting holes provided. Package Contains: 1.      1 x Two channel 5V relay Module.    

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two (2) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and Transistor will further protect your micro-controller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - BC 547 Transistor used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Laptop/Bluetooth Controlled Wireless Robot Robot Controlled By Laptop over Bluetooth Wireless Protocol. PACKAGE INCLUDES: 1) A ASSEMBLED Laptop/Bluetooth Controlled Wireless Robot 2) Pre- Built Windows Application By Robosoft Labs to drive the robot (Source code won't be provided due to copyright issue)   Laptop/Bluetooth Controlled Wireless Robot IS ASSEMBLED OF FOLLOWING LISTED ITEMS: 1) TWO L TYPE BO DC MOTOR (+5V TO +12V) 2) 2 CLAMPS 3) 1 CASTOR WHEEL 4) TWO WHEELS 5) L293D BOARD (MOTOR DRIVER BOARD) 6) CHASSIS 7) BLUETOOTH RECEIVER MODULE 8) 1 AVRDUINO/ARDUINO COMPATIBLE BOARD WITH AVR'S ATMEGA 8 IC 9) CONNECTING BURG WIRES 10) TUTORIAL GUIDE TEACHING HOW TO ASSEMBLE THE ROBOT FROM SCRATCH PARTS TO A Laptop/Bluetooth Controlled Wireless Robot. 11) PRE BUILT AND BURNT Laptop/Bluetooth Controlled Wireless Robot PROGRAM IN AVRDUINO ATMEGA 8 IC 12) NUT AND BOLTS. Points to be noted: 1) This Laptop/Bluetooth Controlled Wireless Robot is ASSEMBLED BY PRE-FABRICATED PARTS. 2)  Laptop/Bluetooth Controlled Wireless Robot CHASSIS is made of PLY WOOD 3) PROGRAM CODE or HEX FILE WONT BE PROVIDED Due to Copyright Issue. 4) Power Supply for Robot: Please use Only +9V battery supply (Batteries not Included as it can't be shipped)   5) Color of Components used may vary according to availability.                        FOR ANY QUERIES OR DOUBT PLEASE CONTACT US BEFORE ORDERING                                                                       E-MAIL:                                                                       MOBILE: +91- Regards, ROBOSOFT LABS                                                                  

ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT T his Wireless robot is control by ANDROID APP with the help of BLUETOOTH Wireless Protocol. This ANDROID APP also Supports VOICE COMMANDS to drive the robot too. PACKAGE INCLUDES: 1) A ASSEMBLED ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT 2) Pre- Built ANDROID APP By Robosoft Labs to drive the robot. (APP source code/program won't be provided due to copyright issue) ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT IS ASSEMBLED OF FOLLOWING LISTED ITEMS: 1) TWO L TYPE BO DC MOTOR (+5V TO +12V) 2) 2 CLAMPS 3) 1 CASTOR WHEEL 4) TWO WHEELS 5) L293D BOARD (MOTOR DRIVER BOARD) 6) CHASSIS 7) BLUETOOTH RECEIVER MODULE 8) 1 AVRDUINO/ARDUINO COMPATIBLE BOARD WITH AVR'S ATMEGA 8 IC 9) CONNECTING BURG WIRES 10) TUTORIAL GUIDE TEACHING HOW TO ASSEMBLE THE ROBOT FROM SCRATCH PARTS TO A ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT. 11) PRE BUILT AND BURNT ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT PROGRAM IN AVRDUINO ATMEGA 8 IC 12) NUT AND BOLTS. Points to be noted: 1) This ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT is ASSEMBLED BY PRE-FABRICATED PARTS. 2)  ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT CHASSIS is made of PLY WOOD 3) PROGRAM CODE or HEX FILE WONT BE PROVIDED due to COPYRIGHT ISSUE. 4) Power Supply for Robot: Please use Only +9V battery supply (Batteries not Included as it can't be shipped) 5) Color of Components used may vary according to availability. 6) Mobile phone shown is not included

BRAND NEW  HIGH QUALITY  IR  8  Channel Remote Control Relay Board Module with  12V  Relays  5A / 250V AC   Overview: IR Remote control is a combination of Infrared Transmitter and Receiver which contains  8 Relays    which can be controlled wirelessly. This makes the unit very easy to operate and integrate with existing systems. The remote control operates the corresponding relays on the receiver board, i.e. (1 operates Relay 1), (2 operates Relay 2), etc. Each relay has indicator LED showing the ON/OFF status. Applications: Wireless Remote control of Lights and Fan at home or office Wireless Remote control of Projectors and speaker system

Features The is a 5V 8-Channel Relay interface board with optocoupler which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSC, and so on. Can be powered by 5V DC Source (From USB) Or from the same source powered to Arduino or any other micro controller. Equipped with high-current relay 10A@250 VAC / 10A@28 VDC which can control both AC and DC appliances such as Solenoids, Motors, lights, fans etc High quality screw terminals provided for each relays (C, NC, NO) for quick and easy connection Interfaced with optocouplers to isolate relays & protect your microcontroller. Input Signal Pin connected to Burg stick for easy accessibility LED Status indicators to indicate the relay ON/OFF status. Dimension: 13.4 x 5.3 x 1.7cm (5.28 x 2.09 x 0.67in) Mounting holes provided Shipping contents 1 x 5V DC 8 Channel relay board as shown