Power pwm

PWM 12V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - PWM Duty Cycle: %. - Current: Rated Current: Max 5A with heat sink - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

PWM 12V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - Frequency：25KHz. - PWM Duty Cycle: %. - The maximum current up to 5A radiator or heat required - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

PWM 12V/24V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - Frequency：25KHz. - PWM Duty Cycle: %. - The maximum current up to 5A radiator or heat required - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

PWM DC 6V 12V 24V 28V 3A Motor Speed Control Switch Controller Regulator This DC Motor Speed Controller allows controlling the speed of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from %.  The motor speed controller can easily provide a continuous current of3A to your DC motor or other DC load.  Input supply voltage: 5V-30VDC  The maximum output power: 80W  The maximum continuous output current: 3A  Duty Cycle adjustable: %  Operating instruction:  1. Connect your DC motor (or DC load) to the motor terminals as indicated on the wiring diagram.  2. Connect a voltage of 5V-30V DC to the circuit making sure of the correct polarity of the connection. Note that the voltage applied to the motor will be supply voltage applied to the circuit. It is recommended to add an appropriately rated fuse inline with the positive supply

3A Pulse Width PWM DC Motor Speed Regulator Controller Switch 12V/24V/36V Specifications Control the speed of a DC motor with this controller. Control the light of a lamp with this controller. High efficiency, high torque, high power, high heat dissipation. With overcurrent protection. The high quality COMBICON improve the stability of circuit. Input voltage: DC12V - 36V Sustained current:3A,max.6A(Need to add a cooling fan when max. current) PWM Duty Cycle:% Material: Plastic, metal Size (L*W*H):55mm*35mm*21mm To connect the DC power supply:ensure the power supply voltage 12V - 36V, ensure the power supply output power meet the requirements of the motor work.Dc power don't reverse the positive and negative terminals, otherwise the governor may damage; Line connecting motor: the motor can be both positive and negative, when running direction and expectations are not consistent, can adjust the line sequence by position or to change the direction; Adjust potentiometer knob: adjust potentiometer knob can change speed output duty cycle, motor speed change. Package includes PWM DC Motor Speed Regulator Controller Switch x 1 Images Click here to check out our other products

DC 12V-40V Large Torque PWM Motor Speed Controller Reversible Control Switch Specifications High Power, High efficiency, Large torque The motor speed controller incorporates a high power MOSFET with a heat sink and can easily provide a continuous current of 3A to your DC motor or other DC load With switch function and Reversible Control function Onboard 10A fuse, with reverse power, over voltage, high current protection function Mode:CCM2NJ Input supply voltage:VDC(max) Maximum output power:120W rated current: 3A Maximum continuous output protecting current:5A PWM frequency: 15kHz Duty Cycle adjustable:% Indicator: Power-On LED Size: 70x39x31mm/2.75"x1.53"x1.22"(approx) Color: as the picture show Package includes 1 x PWM DC Reversible Motor Speed Controller Images Click here to check out our other products

12V-60V 24V 36VStepless PWM 15khz Variable Fan Motor Speed Controller Switch DC Specifications Power input reverse polarity protection, reverse the positive and negative inputs are not damaged, detachable potentiometer connected to the host via a freely plug cable Dimensions: 70 x 39 x 31 mm Operating voltage: DC 12V-60V Output current: 10A Max. (full power, long-term working) Control power: W Quiescent Current: 0.02A (standby) PWM duty cycle: 5% -99% PWM frequency: 15khz Input Anti-reverse Protection: Yes Package includes DC Motor Speed Controller x 1 Images Click here to check out our other products

Silverstone Technology All Black Sleeved PWM Fan Power Extension Cable (CPF03). CPF03 is a PWM fan power extension cable designed to solve the problem of short-cabled PWM fan

DC PWM V Motor Speed Control 10A Pulse Width Modulator Controller Switch Features Power requirement:V Rated current:10A(Maximum output current) PWM Frequency:HZ Control Motor Power:12V:120W(max),24V:230W(max) Regulation range:% The Pulse type is 10A,High-current protection,or Short-circuit current protection Dimension:80mm x 30mm x 55mm(about) Quantity:1PC Package includes 1 x PWM DC Motor speed controller Images Click here to check out our other products

20A Universal DCV PWM HHO RC Motor Speed Regulator Controller Switch Features Operating voltage: DC 10V-60V Output Current: 0 to 20A. Frequency：25KHz. Continuous power: Max W Speed range: Motor zero speed to maximum motor speed The maximum current up to 20A radiator or heat required to increase the fan Material: Plastic, metal Size (L*W*H):76mm*44mm*26mm Package includes PWM DC Motor Speed Regulator Controller Switch x 1 Images Click here to check out our other products

1.onboard SGA PWM control chip 2.onboard 78 m05 voltage chip, provide reliable reference voltage 3.onboard two precision adjustable resistance, R3 control duty ratio, frequency of R4 control 4.onboard power light 5.working voltage: 8 ~ 12 v 6.board size: 30.8 (mm) x18 (mm) SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you

StarTech.com 12-Inch 4 Pin Fan Power Splitter Cable - F/M (FAN4SPLIT12). The FAN4SPLIT12 Fan Power Splitter Cable enables you to connect two 4-pin (PWM) fans to a single power supply connector which allows you to optimize your computer cooling capability without having to upgrade the power supply. Providing a flexible way to position computer case fans as needed this 4-pin Fan Power Splitter cable offers a connection length of 1ft eliminating the need to strain the connection from the computer power supply

The Only Safe Measurement Solution for Power Electronics Rarely used:The THS720P TekScope IsolatedChannel™ Oscilloscope/DMM is ideal for electrical/ power electronics applications. The THS720P includes features specifically for electrical/power electronics measurements which allow testing and verifying correct operation of motors, checking transformer efficiency, verifying powersupply performance and measuring the effect of neutral current. These features include harmonic analysis, power measurements and statistics and PWM motor drive triggering. It also contains the powerful features of a modern oscilloscope that enable troubleshooting and verification of complicated electronic control circuits controlling the high-voltage powerelectronics circuitry. THS720P Handheld Battery Operated Oscilloscope/DMM. Includes: Two PX Passive Probes, User Manual, Quick Reference Manual, Standard Meter Lead Set, NiCd Rechargeable Battery Pack, AC Power Adapter, Soft Carrying Case, Cable and Adapters for RS-232, NIST-traceable Certificate of Calibration.

Overview: Dedicated CPU Fan Connector Designed for More Reliable Operation. Specific CPU fan controller is design to provide more power for your CPU fan to achieve better cooling performance. Blue LED for More Aesthetic Appearance. Blue LED is specially installed to make your computer case with side window more awesome. Sound-operating Control to Adjust Sensitivity of LED Lightning Rockman’s LED light intensity changes with its surrounding sound, simply adjust the light controller according to your lightning needs. Ideal 3.5 Drive Bay Compatibility Rockman is designed to fit

WELCOME TO THEVALUESTORE MALL     Contact us at  for any queries Mail us at     for any queries Key Features Dual SP120L PWM fans with Corsair Link monitoring and control for extreme liquid CPU cooling performance The Hydro Series H100i GTX is an extreme performance, all-in-one liquid CPU cooler for cases with 240mm radiator mounts. The 240mm radiator and dual SP120L PWM fans provide the excellent heat dissipation you need for highly overclocked CPUs. Corsair Link is built in, so you can monitor temperatures, adjust cooling performance and customize LED lighting directly from your desktop. 240mm radiator The double-wide radiator offers approximately twice the cooling area of our Hydro Series coolers which use a 120mm or 140mm radiator. It fits virtually any case that has dual 120mm fan mounts spaced for a 240mm radiator. Advanced SP120L PWM fans Our custom-designed SP120L fans are different than standard case fans – they’re custom-designed to deliver high static pressure for mounting directly against radiators, and the fan blades are specially shaped for maximum air delivery with minimum noise. Since they’re PWM controlled, you can customize the fan speed to choose the optimal point on the performance/noise curve. Built-in Corsair Link for monitoring, customization, and control Attach the included Corsair Link cable to a USB header on your motherboard and download the free Corsair Link software to unlock even more power. You can customize cooling performance, monitor coolant and CPU temperatures, and change the color of the RGB LED lighting from the default white to match your system, or to change color based on temperature readings and other inputs. High-performance CPU cooling made simple Gone are the days when watercooling required lots of work. The H100i GTX is a closed loop design that comes pre-filled, and it comes with a modular, tool-free mounting bracket for faster installation. About Hydro Series Liquid CPU Coolers Corsair Hydro Series CPU coolers give you the power of liquid cooling

A 280mm radiator and dual SP140L PWM fans provide the extreme cooling you need for highly overclocked CPUs The Hydro Series H115i is an extreme performance, factory sealed, all-in-one liquid CPU cooler for cases with 280mm radiator mounts. The 280mm radiator and dual SP140L PWM fans provide the excellent cooling you need for highly overclocked CPUs. Corsair Link software control is built in, so you can monitor temperatures, adjust cooling performance and customize LED lighting directly from your desktop. 280mm dual-fan radiator The key to fast, efficient cooling is maximizing cooling surface area. If your PC case has dual 140mm fan mounts spaced for a 280mm radiator, the H115i lets you take advantage of your case’s full cooling potential. Improved coldplate and pump design Everything’s been tweaked to make the v2 line our best yet. The new design operates more efficiency for both lower temperatures and less noise. Dual SP140L PWM fans The included 140mm fans are custom-designed for high static pressure air delivery with minimum turbulence and noise. They’re PWM controlled, so you can customize the fan speed to find the optimal balance of cooling and noise. Built-in Corsair Link for monitoring, customization and control Attach the included Corsair Link cable to a USB header on your motherboard and download the free Corsair Link software to unlock even more power. You can customize cooling performance, monitor coolant and CPU temperatures, and change the color of the RGB LED lighting from the default white to match your system, or to change color based on temperature readings and other inputs. High performance CPU cooling made simple Gone are the days when watercooling required lots of work. The H115i is a closed loop, factory sealed design that comes pre-filled, and it comes with a modular, tool-free mounting bracket for faster installation. About Hydro Series Liquid CPU Coolers Corsair Hydro Series CPU coolers give you the power of liquid cooling in a compact, easy-to-install package. They offer superior cooling for higher overclocking performance, without the complexity of traditional water cooling kits. Contents and Specifications Package contents Hydro Series H115i Liquid CPU Cooler Mounting kit for all modern CPU sockets Two SP140L High Torque 140mm Fans USB cable for Corsair Link™ Integration Fan and radiator mounting screws Thermal compound (pre-applied) Quick Start Guide Compatibility Intel™ LGA 1150, 1151, 1155, 1156, 1366, 2011 and 2011-3 AMD™ sockets FM1, FM2, AM2, and AM3 Technical specifications Radiator dimensions: 140mm x 312mm x 26mm Fan dimensions: 140mm x 25mm Fan speed: 2000 +/- 10% RPM   Fan airflow: 104.65 CFM Fan static pressure: 3.99mm-H2O Noise level: 40 dB(A)

A 280mm radiator and dual SP140L PWM fans provide the extreme cooling you need for highly overclocked CPUs The Hydro Series H115i is an extreme performance, factory sealed, all-in-one liquid CPU cooler for cases with 280mm radiator mounts. The 280mm radiator and dual SP140L PWM fans provide the excellent cooling you need for highly overclocked CPUs. Corsair Link software control is built in, so you can monitor temperatures, adjust cooling performance and customize LED lighting directly from your desktop. 280mm dual-fan radiator The key to fast, efficient cooling is maximizing cooling surface area. If your PC case has dual 140mm fan mounts spaced for a 280mm radiator, the H115i lets you take advantage of your case’s full cooling potential. Improved coldplate and pump design Everything’s been tweaked to make the v2 line our best yet. The new design operates more efficiency for both lower temperatures and less noise. Dual SP140L PWM fans The included 140mm fans are custom-designed for high static pressure air delivery with minimum turbulence and noise. They’re PWM controlled, so you can customize the fan speed to find the optimal balance of cooling and noise. Built-in Corsair Link for monitoring, customization and control Attach the included Corsair Link cable to a USB header on your motherboard and download the free Corsair Link software to unlock even more power. You can customize cooling performance, monitor coolant and CPU temperatures, and change the color of the RGB LED lighting from the default white to match your system, or to change color based on temperature readings and other inputs. High performance CPU cooling made simple Gone are the days when watercooling required lots of work. The H115i is a closed loop, factory sealed design that comes pre-filled, and it comes with a modular, tool-free mounting bracket for faster installation. About Hydro Series Liquid CPU Coolers Corsair Hydro Series CPU coolers give you the power of liquid cooling in a compact, easy-to-install package. They offer superior cooling for higher overclocking performance, without the complexity of traditional water cooling kits. Specifications:- Warranty Five years Cold Plate Material Copper Fan Specification 140mm (x2) Radiator Material Aluminum Socket Support AMD: AM2, AM3, FM1, FM2, Intel LGA: 1150, 1151, 1155, 1156, 1366, 2011, 2011-3 Tubing Large-diameter, low permeability

DESCRIPTION Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for Arduino 1. L298N as main chip, ST corporation production. 2. Low heat,outstanding anti-interference performance. 3. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power 25w. 4. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. 5. Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply. 6. Large capacity filter capacitance,afterflow protection diode, more stable and reliable. o Specifications: 2. Double H bridge drive 3. Chip: L298N (ST NEW) 4. Logical voltage: 5V 5. Drive voltage: 5V-35V 6. Logical current: 0mA-36mA 7. Drive current: 2A(MAX single bridge) 8. Size:43 x 43 x 26mm 9. Max power: 25W 10. Net weight: 25g Uses: 11. Driving stepper motor: The connection of driving a common 4 line 2 phase electric motor is shown in figure after enable ENA ENB Input the following driving timing from IN1-IN4-then the speed and direction of the stepper motor can be controlled. 12. Driving DC motor: Because this module is driven by double H bridge,it can drive two motors simultaneously. after enable ENA ENB You can input the speed and direction of PWM signal drive motor 1 from IN1 IN2 You can input the speed and direction of PWM signal drive motor 2 from IN1 IN2 We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description   The FSGM300N is an integrated Pulse Width Modulation (PWM) controller and SenseFET specifically designed for offline Switch-Mode Power Supplies (SMPS) with minimal external components. The PWM controller includes an integrated  fixed-frequency oscillator, Under-Voltage Lockout (UVLO), Leading- Edge Blanking (LEB), optimized gate driver, internal soft-start, temperature-compensated  precise current sources for loop compensation, and self-protection circuitry. Compared with a discrete MOSFET and PWM controller solution, the FSGM series can reduce total cost, component count, size, and weight; while simultaneously increasing efficiency, productivity, and system reliability. This device provides a basic platform suited for cost-effective design  of a flyback converter.

Description: 1.  CH340G REPLACE FT232RL 2.  Operating Voltage(logic level):5V 3.  8 analog inputs ports:A0 ~ A Digital input / output ports:TX,RX,D2 ~ D PWM ports:D3, D5, D6, D9, D10, D pairs of TTL level serial transceiver ports RX / TX 8.  Using Atmel Atmega328P-AU MCU 9.  Support USB download and Power 10. Support for external 5V ~ 12V DC power supply 11. Support power supply by 9V battery     8 analog inputs ports:A0 ~ A7     14 Digital input / output ports:TX,RX,D2 ~ D13     6 PWM ports:D3, D5, D6, D9, D10, D11     1 pairs of TTL level serial transceiver ports RX / TX   Package include: 1pcs + 3 rows of pins = MM_contentVersion; } else if (navigator.userAgent && navigator.userAgent.indexOf("MSIE")>=0 && (navigator.appVersion.indexOf("Win") != -1)) { document.write(' /n'); document.write('on error resume next/n'); document.write('MM_FlashCanPlay = (IsObject(CreateObject("ShockwaveFlash.ShockwaveFlash." & MM_contentVersion)))/n /n'); } if (MM_FlashCanPlay) { document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); } else { document.write(' '); document.write(' '); document.write(' The Buyer Appreciation banner is best viewed with Macromedia Flash Player 6 or higher. '); document.write(' Click here to get the latest Macromedia Flash Player. '); document.write(' '); document.write('

LilyPad 328 ATmega328P Main Board compatible with Arduino’s IDE Features: Brand new and high quality The LilyPad Iduino is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The LilyPad Iduino can be programmed with the software. The ATmega328V on the LilyPad comes preburned with a bootloader that allows you to upload new code to it with the software. You can also bypass the bootloader and program the ATmega through the ICSP (In-Circuit Serial Programming) header. The LilyPad should only be programmed with software versions 0010 or higher. You can program it with earlier versions, but all of the time related functions will be switched off (making them twice as slow as they should be). Warning: Do not power the LilyPad with more than 5.5 volts, or plug the power in backwards: you'll kill it. 328 Main board; The Digital I/O Digital input/output terminal, a total of 0 ~ 13; The Analog I/O Analog input/output terminal, a total of 0 ~ 5; Support the ISP download function; Support the TX/RX terminals; Support the AREF terminals; Support the six groups of PWM terminal (Pin11 Pin10, Pin9, Pin6 and Pin5, responsible); The input voltage: 3.3 V DC; Using Atmel Atmega328V - 20 pu microcontroller; Specifications: Microcontroller: ATmega328V Operating Voltage: 2.7-5.5 V Input Voltage: 2.7-5.5 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 6 DC Current per I/O Pin: 40 mA Flash Memory: 16 KB (of which 2 KB used by bootloader) SRAM: 1 KB EEPROM: 512 bytes Clock Speed: 8 MHz Package includes: 1* LilyPad atmega 328 Main board Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328)

The Arduino Uno is a microcontroller board based on the  ATmega328  (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16  MHz  ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Summary Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16  MHz Length 68.6 mm Width 53.4 mm Weight 25 g

Features: l           Support for the IDE 1.0+ (OSX/Win/Linux) l           Power via USB or External Source l           On-board 500ma 5V Regulator l           Built-in USB(and serial debugging) l           6 I/O Pins (2 are used for USB only if your program actively communicates over USB otherwise you can use all 6 even if you are programming via USB) l           8k Flash Memory (about 6K after bootloader) l           I2C and SPI(vis USI) l           PWM on 3 pins (more possible with Software PWM l           ADC on 4 pins l           Power LED and Test/ Status LED (on Pin0) 　 Package includes: l        1x Digispark Miniature USB Development Board l        1x 3-Pin connector l        1x 6-Pin connector Note: As the package is very big and the shipping fee would be very high, we will ship the item out without its original box. Anyhow, the shipping is very safe. Also available                                 Digispark Kickstarter USB Development Board for Arduino Tiny 85 (USB Male A Interface) Important  Note:  Please check your shipping address during checkout. powership policies do not allow change of address after payment. You have order the item again to change the shipping address. Now Fast shipping with  powerShip  through  Blue Dart / DTDC / Aramex / FedEx. 

Features: l           Support for the IDE 1.0+ (OSX/Win/Linux) l           Power via USB or External Source l           On-board 500ma 5V Regulator l           Built-in USB(and serial debugging) l           6 I/O Pins (2 are used for USB only if your program actively communicates over USB otherwise you can use all 6 even if you are programming via USB) l           8k Flash Memory (about 6K after bootloader) l           I2C and SPI(vis USI) l           PWM on 3 pins (more possible with Software PWM l           ADC on 4 pins l           Power LED and Test/ Status LED (on Pin0) 　 Package includes: l        1x Digispark Miniature USB Development Board l        1x 3-Pin connector l        1x 6-Pin connector Note: As the package is very big and the shipping fee would be very high, we will ship the item out without its original box. Anyhow, the shipping is very safe. Also available                                 Digispark Kickstarter USB Development Board for Arduino Tiny 85 (micro-USB Female Interface) Important  Note:  Please check your shipping address during checkout. powership policies do not allow change of address after payment. You have order the item again to change the shipping address. Now Fast shipping with  powerShip  through  Blue Dart / DTDC / Aramex / FedEx. 

Package Contains 1XArduino Uno R3 1X Usb Cable for Arduino The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

Arduino UNO (Q021) The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g

Description: 100% brand new and high quality The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much. The Digispark is shipped fully assembled except for the two included and easy to solder headers. Here are the specs: Support for the Arduino IDE 1.0+ (OSX/Win/Linux) Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection)On-board 500ma 5V Regulator Built-in USB6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB) 8k Flash Memory (about 6k after bootloader) I2C and SPI (vis USI)PWM on 3 pins (more possible with Software PWM) ADC on 4 pins Power LED and Test/Status LED Size:2x1.7cm(approx) Package Included: 1 x Digispark Kickstarter Attiny85 USB Development Board for Arduino Full Wiki link:  digispark Wiki         Software: NOTE:  If you used a version of the ide where the digistump add-ons were installed separately you must delete the digistump folder at My Documents/Arduino/hardware (windows) or Documents/Arduino/hardware (OS  X) or /home/[username]/Sketchbook (Linux) or this new IDE install will not work properly and you will get library errors! The Digispark uses the Arduino IDE - Digistump Release 1.5.x which is the Arduino IDE with some custom additions and supports Digispark, Digispark Pro, and DigiX. These are presented as a fully integrated package with 1.5.x that can be downloaded as an installed or zip file. First download the appropriate package: Windows (now with fully signed drivers!) Installer (recommended): https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpArduinoInstall1.5.8C.exe Zip:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8C.zip Mac:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8COSX.zip Linux: 32-bit:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8C-linux32.tar.gz 64-bit:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8C-linux64.tar.gz Note: report any issues with the builds to the forum:  http://digistump.com/board Compiling from source:  https://github.com/digistump/DigistumpArduino Windows Install Complete these steps before plugging

Description High quality Digispark Kickstarter USB Development Board for Arduino. The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much. The Digispark is shipped fully assembled except for the two included and easy to solder headers. Technical parameters: Support for the Arduino IDE 1.0+ (OSX/Win/Linux) Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection) On-board 500ma 5V Regulator Built-in USB 6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB) 8k Flash Memory (about 6k after bootloader) I2C and SPI (vis USI) PWM on 3 pins (more possible with Software PWM) ADC on 4 pins Power LED and Test/Status LED   Package Contents: High quality Digispark Kickstarter USB Development Board for Arduino Feedback: We provide good quality products & maintain high customer service standards.  We strive for 100% positive feedback for our service.  For assistance, please contact us on  Message  or  If you are satisfied with our service we request you to please leave us a positive feedback and 5 Star DSR ratings