Connection board

n/Out Connection Board is a simple PCB offering easy connection of a standard 10-pin Box Header connector to screw terminal connector or berg connector.  This PCB also has an AUX power screw terminal connector through which you can either source or supply power to your projects. PCB dimensions 39 mm x 58 mm

Set of 4 Pcs AVR40 Base Board  Kit.  For Electronic project.  Atmel AVR - 40 Pin Base Boar d (For ATmega16, AT mega 32,Microcontroller) 1 Pcs 6 Digital Sensors Board for Line Follower    1 Pc 16X2 LCD Board for Display 1 Pc L298N Dual H-Bridge Motor Driver Board. **FREE**4 Pcs FRC Cable. ** Does not Include Any Microcontroller ** Atmel AVR - 40 Pin Base Board AVR-40Pin Development Board -For 40 pin AVR like ATMEGA16, ATMEGA32 etc it Comes without   micocontroller 1 Pc L298N Dual H-Bridge Motor Driver Board. 6 Digital IR - Photodiode Sensors Array for LFR Robot 6 IR-Photodiode Sensors Array- for Line following robot (LFR) and micro-mouse robot  (Digital out, Independent Manual Adjustable) Ideal for LFR (line-follower Robot) obstacles avoiding robots obstacles chasing robot side wall sensor maze solving robots 16x2 LCD Display Board Box Header Connection > LCD Connection (4Bit Mode) Pin#1   > RS(4) Pin#2   > EN(6) Pin#3   > D4(11) Pin#4   > D5(12) Pin#5   > D6(13) Pin#6   > D7(14) Pin#7   > No Connection Pin#8   > No Connection Pin#9   > Gnd () Pin#10 > +5V (2) Note Pin#5 of LCD (RW) is forcefully connected to Ground L298N Dual H-Bridge Motor Driver Board New Improved L298 Dual H-Bridge Board - Ideal for robot motor control, smart  full feature,compact, Compatible with AVR - 40 Board 10 Pin Box Header Connection Description Pin1= ENABLE B Pin2= ENABLE A Pin3= INPUT-3 Pin4= INPUT-1 Pin5= INPUT-4 Pin6= INPUT-2 Pin7= NOT CONNECTED Pin8= NOT CONNECTED Pin9= Ground Pin10=Vcc +5Volt    Fore More Details please refer Datasheet of L298N. ****FREE**** 4 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm. ,with female connectors on both ends. Please Clear Any Doubts "BEFORE" Buying any products form us. Fast Shipping via*      * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post. Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                                                        For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline: Powered by Turbo Lister

This simple A2D (Analog to Digital) Converter Board can log upto 8 channel of analog signal with 8 bit resolution.  This board uses the famous ADC chip from National Semiconductor. Two standard box type header connector for easy connection of the board to various development boards or project Separate box header for Data and Control signal for the ADC Screw terminal connector for easy connection of Analog signal input or sensor connection to the board +5 VDC and Gnd connection available for sourcing supply for your sensor or add-on interface or signal conditioner board Onboard oscillator source for the analog to digital converter Four mounting holes 3.2 mm each PCB dimensions 54 mm x 63 m

Ethernet W Shield Network Expansion Board w/ Micro SD Card Slot for Arduino (Q022) Product Features:. The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W ethernet chip (datasheet). The Wiznet W provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO board for further development. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Duemilanove and Mega (using the Ethernet library). Ethernet shield network expansion board for Arduino. The Arduino ethernet shield allows an Arduino board to connect to the internet It is based on the Wiznet W ethernet chip (datasheet). The Wiznet W provides a network (IP) stack capable of both TCP and UDP It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. Requires an Arduino board (not included). Operating Voltage 5V (supplied from the Arduino Board) Product Features The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W ethernet chip (datasheet). The Wiznet W provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO board for further development There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Duemilanove and Mega (using the Ethernet library). Ethernet shield network expansion board for Arduino The Arduino ethernet shield allows an Arduino board to connect to the internet It is based on the Wiznet W ethernet chip (datasheet) The Wiznet W provides a network (IP) stack capable of both TCP and UDP It supports up to four simultaneous socket connections Use the Ethernet library to write sketches which connect to the internet using the shield Requires an Arduino board (not included) Operating Voltage 5V (supplied from the Arduino Board) Ethernet Controller W with internal 16K buffer Connection Speed Mb Connection with Arduino on SPI port

Sensor Shield v5.0 expansion board for arduino electronic building blocks robot accessories Sensor Shield V5 expansion board Latest Sensor Shield V5.0 sensor expansion board to retain the advantages of version V4.0 on the basis of still only stack design, PCBImmersion Gold processing technology, the motherboard is not only the Duemilanove 2009 controller digital and analog interfacesequenceform of steering gear line extension, but also ad hoc IIC interface 32 servo controller Interface Bluetooth module communication interface, SD card module communication interface, the APC220 wireless RF module communication interface, the RB The URF v1.1 ultrasonic sensor interface12864serial and parallel interfaces, independent expansion of a more easy-to-use convenience. For beginners, you do not have a headache forthe cumbersome and complex circuit connection, the sensor extends the true sense of the board to simplify the circuit can easily connect thecommonly used sensor, a sensor requires only a common 3P the sensor cable (regardless of digital cable and analog cable), after the completion ofthe circuit connection, the preparation of the corresponding program downloaded to the Duemilanove controller reads the sensor data, or receive wireless module to return data after computing the final easy to complete your own interactive works. Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Package Contents   1 x PIC development Board with Free USB cable and CD containing software examples.   External Power supply NOT Included.    Contact Details   Have any Queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"    The PIC development board is a microcontroller board based on the PIC16F877. It has 33 input/output pins and two PWM outputs, 8 (10 bit) analog inputs, a works upto 20 MHz speed. A USB connection is available for programming and UART (communication with the PC), an external power jack is provided for high current motor applications etc. A Reset button is present. A 4 x 4 key matrix is provided for keyscan applications. A 16 x 2 LCD with programmable backlight is provided. A Piezo Buzzer is present. A 4 digit 7 segment common cathode display is populated for display multiplexing example. A onboard potentiometer is provided on one analog channel. A coin cell battery backed DS (RTC) is present on one of the I2C channel. An optional SPI external EEPROM (not provided with the board) can be mounted by the user for SPI memory. A ULN based stepper motor interface is present.   The Board contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. FEATURES AND USAGE The maximum length and width of the Board is approx 7 inch by 5.5 inches. Four PCB studs allow the board to be attached to a surface or act like a support stand. All the ports of the microcontroller are available as edge connectors on the right side of the board on a standard 100 mil spacing. The board can also take most of the 40 Pin DIP PIC18 series microcontrollers. An External programmer may be needed

With this board you can develop and prototype with ATMEGA16/ATMEGA pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters.   FEATURES AVR Development Board for Atmel ATMEGA ISP Socket for Flashing On board Regulated Power Supply 5v,12v supplys Easy to test with Burg Connecters wires An RS232 Serial Port 7Seg Mulitplexed Display DC Power Supply Connector(12v Ac or Dc) READY INTERFACE For LCD display 2linex16Character 24Cxx (I2C) (EEPROM) RTC (DS LED array Matrix Key Pad 4 Interrupt Switches +12v Relay (one) Package Content   AVR Development Board (WITH CHIP MAX232) Burg Connecters 20 Nos Female to Female.

Description Single Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has ONE relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a Single channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description Four Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has FOUR relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a 4 channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

SAM3X8EA 32bit ARM Contex-M3 Due R3 Board Control  Arduino Due R3 AT91SAM3X8E   Description The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. Features: 1. Microcontroller ：AT91SAM3X8E   2. Operating Voltage：3.3V  3. Input Voltage (recommended)：7-12V  4. Input Voltage (limits)：6-16V  5. Digital I/O Pins ：54 (of which 12 provide PWM output)  6. Analog Input Pins：12 7. Analog Outputs Pins：2 (DAC) 8. Total DC Output Current on all I/O lines ：130 mA 9. DC Current for 3.3V Pin：800 mA   10. DC Current for 5V Pin：800 mA  11. Flash Memory：512 KB all available for the user applications  12. SRAM：96 KB (two banks: 64KB and 32KB)   13. Clock Speed：84 MHz            Driver installation and usage procedure: ·                      Install  Arduino IDE ß  (click here) no extra driver needed for this card. ·                      Connect the board to computer, OS will auto detect ARDUINO DUE ·                      If the board is not auto detected, go to hardware device manager and choose update driver than choose advanced option “install from specific location” and point to the directory where your Arduino IDE is installed e.g. ”C:/program files/arduino-1.0.2/drivers” ·                      Launch Arduino IDE, select board as “arduino DUE” ·                      Select the com port OS created for the card(control panel  à  device manager) ·                      Open basics  à  blink sketch and upload. Package: 1 MCU BOARD  + 1 USB cable

Package Contents 1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has one (1) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free wheeling diode which will further protect your microcontroller from relay kick back. This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Free wheeling diode to protect your microcontroller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four (4) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has 2 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Description: Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two Two on-board relay which can switch up to 7Amps. Relays terminals (COM, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free-wheeling diode which will further protect your microcontroller from relay kick back. This is a 5V 2-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.    Features: 1.     Equipped with high-current relay 7A@250VAC / 10A@24VDC.  2.     It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. 3.     High quality screw terminals (Terminal Block) provided (COM, NC, NO) for quick and easy connection. 4.     Free wheeling diode to protect your microcontroller. 5.     Input Signal Pin connected to Burg stick for easy accessibility. 6.     LED Status indicators to indicate the relay ON/OFF status. 7.     Mounting holes provided. Package Contains: 1.      1 x Two channel 5V relay Module.    

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two (2) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and Transistor will further protect your micro-controller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - BC 547 Transistor used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Description: 20 Digital Input / Output. Tx, Rx, D2~D13, A0~A5. 8 Analogue Inputs. A0~A7. 6 PWM Ports. D3, D5, D6, D9, D10, D11. Arduino-compatible Board. ATmega328 running at 16MHz with external resonator (0.5% tolerance) USB connection off board (Supports Serial Download) Supports auto-reset Max 150mA output Over current protected Reverse polarity protected DC input 5V up to 12V On board Power and Status LEDs Dimensions（Long）33mm *（wide）18 mm *（high）6mm Package Content: 1x Arduino Pro Mini Atmega 328P board  3PCS Gilded Pin

Why to buy  Pro Mini ATMEGA168  ? When you get Pro Mini Atmega328P. 32KB of Program Memory + 2KB SRAM + Byte EEPROM Product Description: 20 Digital Input / Output. Tx, Rx, D2~D13, A0~A5. 8 Analogue Inputs. A0~A7. 6 PWM Ports. D3, D5, D6, D9, D10, D11. Arduino-compatible Board. ATmega328 running at 16MHz with external resonator (0.5% tolerance) USB connection off board (Supports Serial Download) Supports auto-reset Max 150mA output Over current protected Reverse polarity protected DC input 5V up to 12V On board Power and Status LEDs Dimensions（Long）33mm *（wide）18 mm *（high）6mm Package Content: 1x Arduino Pro Mini Atmega 328P board  3PCS Gilded Pin

We offer a large selection of single channel to multi channel Relay Drivers for applications ranging from low power signal switching to high voltage, high current applications.  Quad channel relay controller we have a configuration to fit every need.  Quad channel relay can be controlled by feeding 2 to 5 V TTL from Micro-controller Development Boards, Remote Receivers, or any other circuit which required isolated high current and high voltage switching by applying TTL voltage.  LED indication for Relay On/Off, Relay Output normally open and normally close via screw terminal for easy connection.  Clamp diodes for current limiting for self protections.  Input via berg connector.  Board can control AC or DC load. Input supply 12 VDC @ 170 mA Output  four SPDT relay Relay specification 5 A @ 230 VAC Trigger level 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED on each channel indicates relay status Screw terminal connector for easy relay output and aux power connection Four mounting holes of 3.2 mm each PCB dimensions 88 mm x 68 mm DO IT YOUR SELF KIT (DIY) Kit contains components, PCB and Circuit Diagram

Opto-Isolated 4-Channel Triac Board (R) is used for fast switching applications.  Ideal for switching mains circuits, lights, appliances, AC motors, solenoids and small load.  Each circuit is effectively isolated with opto-isolators on each channel, TTL inputs control each channel. Trigger input 5 VDC, individual cathode and anode out Mains supply input 230 VAC or 110 VAC Output 1 A @ 230 VAC Snubber circuit for inductive load switching Jumper setting for cathode to common ground Box Header connector for connection of control signal Screw terminal connector for easy Triac output connection Four mounting holes of 3.2 mm each PCB dimensions 139 mm x 73 mm Assembled

We offer a large selection of single channel to multi channel Relay Drivers for applications ranging from low power signal switching to high voltage, high current applications.  Dual channel relay controller we have a configuration to fit every need.  Dual channel relay can be controlled by feeding 2 to 5 V TTL from Micro-controller Development Boards, Remote Receivers, or any other circuit which required isolated high current and high voltage switching by applying TTL voltage.  LED indication for relay On/Off, Relay Output normally open and normally close is via screw terminal for easy connection.  Clamp diodes for current limiting for self protections.  Input via berg connector.  Board can control AC or DC load. Input supply 12 VDC @ 84 mA Output two SPDT relay Relay specification 5 A @ 230 VAC Trigger level 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED on each channel indicates relay status Screw terminal connector for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 49 mm x 68 mm DO IT YOUR SELF KIT (DIY) Kit contains components, PCB and Circuit Diagram

Description: The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout. The Arduino Due can be powered via the USB connector or with an external power supply. A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

PRODUCT DETAILS: Arduino UNO R3 Compatible Board ATmega328P ATmega16U2 with USB cable DESCRIPTION This is a Compatible board for Arduino uno r3, not original This UNO is a 100% compatible derivative of current R3 Arduino UNO The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller;simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Features:- Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

www.hitroncomponents.com Package Contents   1 x UNO R3 ARDUINO COMPATIBLE DEVELOPMENT BOARD 1 x FREE USB Cable   "EXTERNAL POWER SUPPLY IS NOT INCLUDED & HAS TO BE PURCHASED SEPARATELY"   Buy Original Arduino UNO R3 from  http://store.arduino.cc/index.php?main_page=product_info&cPath=11&products_id=195 Download Arduino IDE & Drivers:  http://arduino.cc/en/Main/Software For bulk order get special price Contact Details   Have any queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"       The Arduino Uno is a microcontroller board based on the  ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards

Features The is a 5V 8-Channel Relay interface board with optocoupler which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSC, and so on. Can be powered by 5V DC Source (From USB) Or from the same source powered to Arduino or any other micro controller. Equipped with high-current relay 10A@250 VAC / 10A@28 VDC which can control both AC and DC appliances such as Solenoids, Motors, lights, fans etc High quality screw terminals provided for each relays (C, NC, NO) for quick and easy connection Interfaced with optocouplers to isolate relays & protect your microcontroller. Input Signal Pin connected to Burg stick for easy accessibility LED Status indicators to indicate the relay ON/OFF status. Dimension: 13.4 x 5.3 x 1.7cm (5.28 x 2.09 x 0.67in) Mounting holes provided Shipping contents 1 x 5V DC 8 Channel relay board as shown

8 Servo Adapter Board is a small board which offers connection/interface to upto 8 servo's via a standard 10 pin (5x2) box header connector. Power supply for the servos is sourced via separate onboard screw terminal connector with LED indicator Well marked berg connector for connecting servos Four mounting holes of 3.2 mm each PCB dimensions 60 mm x 25 mm

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328)

The Freeduino is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Before connecting the Freeduino, CP Driver installation would be required.   Got to link below http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx Or google CP driver download. ------------àSelect as per your Operating system and download the driver------------àUnzip the file on desktop ------------àConnect the UNO with USB Cable given to your computer------------àDevice Manager will display Unknown device for the UNO (CP IC). Right click on the same and click on update driver. Give path as desktop. Wait till driver is installed. ------------àYour CP Driver is installed and Uno is ready for use.