Dc motor driver board

Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC   Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V   Driven part of the peak current Io: 2A   The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)   The logical part of the operating current range: 0 ~ 36mA   Storage temperature: -25 Deg C ~ +130 Deg C   Other Extensions: control of direction indicators, the logic part of the plate to take power interface.Driver Board Size: 55mm * 60mm * 30mm   Drive plate Weight: 33g   Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.

DC Motor / Stepper Driver H Bridge Controller This motor driver is perfect for robotics and mechatronics projects and perfect for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms, etc This is a high power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L298 motor driver IC and has onboard 5V regulator which it can supply to an external circuit. It can control upto 4 DC motors, or 2 DC motors with directional and speed control It can drive motors upto 46V with a total DC current of up to 4A. You can connect the two channels

Motor driver, ultrasonic distance sensor Bread board, water flow sensor measure LED display, IR sensor etc. At reduced cost not using that's why selling anyone can also buy any of them

This is L293D based H-Bridge motor driver board for driving DC motors and is ideal for robotics applications. PTR CONNECTORS FOR EASY CONNECTIONS USER ACCESSIBLE MOTOR ENABLE PINS FACILITY ON BOARD V POWER REGULATOR, NO NEED TO GIVE EXTERNAL 5v POWER SUPPLY ON BOARD POWER LED AND POWER ON OFF SWITCH WIRE CONNECTOR FOR INPUT SIGNAL

THIS L293D DRIVER MODULE IS A MEDIUM POWER MOTOR DRIVER PERFECT FOR DRIVING DC MOTORS AND STEPPER MOTORS. IT USES THE POPULAR L293D MOTOR DRIVER IC. IT CAN DRIVE 4 DC MOTORS IN ONE DIRECTION, OR DRIVE 2 DC MOTORS IN BOTH THE DIRECTIONS. FEATURES AND USAGE L293D motor driver IC. Male burg stick connectors for supply, ground and input connection Screw terminal connectors for easy motor connection This motor driver is perfect for robotics and mechatronics projects for controlling motors from microcontroller, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms

The DRV stepper motor driver carrier is a breakout board for TI’s DRV microstepping bipolar stepper motor driver. The DRV features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from  V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling). This product is a carrier board or breakout board for TI’s DRV stepper motor driver; we therefore recommend careful reading of the DRV datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features: Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45 V maximum supply voltage Built-in regulator (no external logic voltage supply needed) Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer, 2 oz copper PCB for improved heat dissipation Exposed solderable ground pad below the driver IC on the bottom of the PCB This product ships with all surface-mount components—including the DRV driver IC—installed as shown

    Other Items Feedbacks About Us Contact Us Add To Favorites   CNB353 - New Original L298N H-Bridge Motor Driver IC for DC,Stepper Motor Drive Make your own DC,Stepper motor Drive/CNC drive Circuit Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

  Description Package Includes: 1 Piece new  TB6560 Driver Board CNC Router Single 1 Axis Controller Stepper Motor Drivers 3A

DESCRIPTION MatLogix Arduino Uno Board with Universal Shield The ARDUINO Board (ATMEGA 8-L) is a microcontroller board based on the ATmega 8-L. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8 up to programmed as a USB-to-serial converter. Universal Shield: Features: A monolithic integrated, high voltage, high current, 4-channel driver Using this chip you can use DC motors and power supplies of up to 36 V, so that some pretty big motors and the chip can supply a maximum current of 600mA per channel Also known as a type of H-Bridge, which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping LDR (light Sensor) for detecting the intensity of light. On board Regulated Power Supply 5v,12v supplys A Serial Port DC Power Supply Connector(12v Dc) LCD display 2x16Character Extra Vcc and Gnd Pins from which you can connect different devices. Potentiometer to set the light intensity of LCD Screen. Reset Switch to reset the arduino board. Slot for TSOP sensor. Kit Content: 1 x Arduino Uno Board 1 x 16x2 LCD (Female) 1 x L293D IC 1 x LDR 1 x USB Cable We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

New L293D motor shield, the input voltage DCV 600mA OUTPUT CURRENT CAPABILITY PER CHANNEL 1.2A PEAK OUTPUT CURRENT (non repetitive)PER CHANNEL ENABLE FACILITY OVERTEMPERATURE PROTECTION LOGICAL "0" INPUT VOLTAGE UP TO 1.5 V(HIGH NOISE IMMUNITY) INTERNAL CLAMP DIODES The Device is a mnolithic integrated high voltage,high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoides, DC  and stepping motors) and switching power transistors.To simplify use as two bridges each pair of channels is equipped with an enable input. A separate supply input is provided for the logic, allowing operation at a lower voltage and internal clamp diodes are included. This device is suitable for use

Step into motor usually defines has step from corner or step number parameter, General of motor a go are is is divided into 200 step, is step from corner for 1.8 degrees, EasyDriver has step from subdivision features, this paragraph drive Board of fine is divided into 8 subdivision, is will motor of each step again fine is divided into 8 step, such can can get more precise of control, that is EasyDriver needs step to completed a full of 360 degrees rotating. Ms1 and MS2 is a stepping motor subdivision resolution selection logic input port; Dir is the choosing of motor operation; Reset to reset the chip initializer and block all external output; Step pulse input ports; Out1a, out1b, out2a, and out2b into two h bridge on the output port; Enable to enable; Sleep sleep mode; Sense1, sense2 for h-bridge current detecting resistors; REF is the reference voltage; GND for logic and power; RC1, RC2 for the h-bridge is a fixed deadline for analog inputs. Aslb is United States Allegro produced micro-step PWM constant current control of two-phase stepping motor driven dedicated drive. Its operating voltage up to 30v, current up to 750ma, one aslb driving a two phase stepping motor enables 8 subdivision driving. Chip internal PWM current control circuit can be set through PFD voltage for slow and fast, mixing three current decay modes, if the PFD-side voltage is higher than 0.6vdd, slow decay mode is selected. Below the 0.21vdd, fast decay mode is selected. Mixed decay modes between the two. In addition, aslb provides perfect protection measures, including the transient voltage, overheat protection, preventing current passthrough, under-voltage lock function. Aslb and does not require additional interface circuitry between the microprocessor, the chip-production easystepper Interface, 8 control lines was reduced 2 (step size and direction), you simply enter the control pulses for stepper motor, embedded converters for stepping motor control can be achieved. Aslb need a few resistors and capacitors to adjust its parameters throughout the driving circuit is very simple. Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Step into motor usually defines has step from corner or step number parameter, General of motor a go are is is divided into 200 step, is step from corner for 1.8 degrees, EasyDriver has step from subdivision features, this paragraph drive Board of fine is divided into 8 subdivision, is will motor of each step again fine is divided into 8 step, such can can get more precise of control, that is EasyDriver needs 1600 step to completed a full of 360 degrees rotating. Ms1 and MS2 is a stepping motor subdivision resolution selection logic input port; Dir is the choosing of motor operation; Reset to reset the chip initializer and block all external output; Step pulse input ports; Out1a, out1b, out2a, and out2b into two h bridge on the output port; Enable to enable; Sleep sleep mode; Sense1, sense2 for h-bridge current detecting resistors; REF is the reference voltage; GND for logic and power; RC1, RC2 for the h-bridge is a fixed deadline for analog inputs. A3967slb is United States Allegro produced micro-step PWM constant current control of two-phase stepping motor driven dedicated drive. Its operating voltage up to 30v, current up to 750ma, one a3967slb driving a two phase stepping motor enables 8 subdivision driving. Chip internal PWM current control circuit can be set through PFD voltage for slow and fast, mixing three current decay modes, if the PFD-side voltage is higher than 0.6vdd, slow decay mode is selected. Below the 0.21vdd, fast decay mode is selected. Mixed decay modes between the two. In addition, a3967slb provides perfect protection measures, including the transient voltage, overheat protection, preventing current passthrough, under-voltage lock function. A3967slb and does not require additional interface circuitry between the microprocessor, the chip-production easystepper Interface, 8 control lines was reduced 2 (step size and direction), you simply enter the control pulses for stepper motor, embedded converters for stepping motor control can be achieved. A3967slb need a few resistors and capacitors to adjust its parameters throughout the driving circuit is very simple. Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Package Contents 1 x L298N DC Driver Controller Stepper Motor smart Car Board Module Dual H Bridge DC Motor Driver Arduino PIC, Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC    Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V    Driven part of the peak current Io: 2A    The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)    The logical part of the operating current range: 0 ~ 36mA    Storage temperature: -25 Deg C ~ +130 Deg C    Other Extensions: control of direction indicators, the logic part of the plate to take power interface. Driver Board Size: 55mm * 60mm * 30mm    Drive plate Weight: 33g    Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.     Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Wireless 4 Channel Robot Control Kit With Dual DC Motor Drive 433Mhz RF  Best Quality @ Lowest Price Control your robot from remote using this 4 channel wireless remote control kit. Kit comes with one 4 channel wireless transmitter with push buttons on-board for sending commands to receiver unit to control the robot. Receiver unit comes with on-board L293D bidirectional dual DC motor driver. Simply Connect 9V battery to Transmitter and proper power source to receiver, connect two DC motors on receiver module and you are ready to control your two or four wheel drive robot within few minutes. You can easily control your robot reverse, forward, left & right. Description Transmitter Input Supply: 9V Battery Receiver Power Supply: 9 - 15 V DC through Battery OR Power Adapter DC Motor Output Channel: 2  Output Current Per Channel: 600 mA (Can Easily drive BO Motors OR Plastic Gear Robotic Motors) Address Selection: 8 BIT On-board DIP Switch RF Frequency: 433Mhz USE: Indoor & Outdoor Applications  Robot Controller, Wireless Remote Controller, Wireless Switching, Wireless Dual DC Motor Drive, DIY Robotic Kits:Package Includes: 1 X 4 Channel Wireless Transmitter 1 X 4 Channel Wireless Receiver With On-board Dual DC Motor Driver 1 X 9V Battery Clip (9V Battery Is not Included) For any  queries  please feel free to write us using "Ask Seller a Question" link  OR  Call us on 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller, 433Mhz, RF Module, DC Motor Driver, DC Motor Drive, l293d, 4ch wireless, 4 channel wireless remote control kit, wireless robot controller, robot, robot controller,

Set of 4 Pcs AVR40 Base Board  Kit.  For Electronic project.  Atmel AVR - 40 Pin Base Boar d (For ATmega16, AT mega 32,Microcontroller) 1 Pcs 6 Digital Sensors Board for Line Follower    1 Pc 16X2 LCD Board for Display 1 Pc L298N Dual H-Bridge Motor Driver Board. **FREE**4 Pcs FRC Cable. ** Does not Include Any Microcontroller ** Atmel AVR - 40 Pin Base Board AVR-40Pin Development Board -For 40 pin AVR like ATMEGA16, ATMEGA32 etc it Comes without   micocontroller 1 Pc L298N Dual H-Bridge Motor Driver Board. 6 Digital IR - Photodiode Sensors Array for LFR Robot 6 IR-Photodiode Sensors Array- for Line following robot (LFR) and micro-mouse robot  (Digital out, Independent Manual Adjustable) Ideal for LFR (line-follower Robot) obstacles avoiding robots obstacles chasing robot side wall sensor maze solving robots 16x2 LCD Display Board Box Header Connection > LCD Connection (4Bit Mode) Pin#1   > RS(4) Pin#2   > EN(6) Pin#3   > D4(11) Pin#4   > D5(12) Pin#5   > D6(13) Pin#6   > D7(14) Pin#7   > No Connection Pin#8   > No Connection Pin#9   > Gnd () Pin#10 > +5V (2) Note Pin#5 of LCD (RW) is forcefully connected to Ground L298N Dual H-Bridge Motor Driver Board New Improved L298 Dual H-Bridge Board - Ideal for robot motor control, smart  full feature,compact, Compatible with AVR - 40 Board 10 Pin Box Header Connection Description Pin1= ENABLE B Pin2= ENABLE A Pin3= INPUT-3 Pin4= INPUT-1 Pin5= INPUT-4 Pin6= INPUT-2 Pin7= NOT CONNECTED Pin8= NOT CONNECTED Pin9= Ground Pin10=Vcc +5Volt    Fore More Details please refer Datasheet of L298N. ****FREE**** 4 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm. ,with female connectors on both ends. Please Clear Any Doubts "BEFORE" Buying any products form us. Fast Shipping via*      * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post. Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                                                        For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline: Powered by Turbo Lister

Other Items Feedbacks About Us Contact Us Add To Favorites New 6 Pc Complete DTMF (Mobile) Controlled Robot Kit  with L298Motor Driver Board. Kit Contains DTMF Driver Board L298 Motor Driver Board FRC Cable Crocodile Clip-DC Jack Cable Microphone Input Cable 3.5mm Stereo Extension Cable  (Doesnt Contain Motors and other ACCESSORIES) + + DTMF (Mobile) Controlled Robot Kit (with L298 Board) for controlling 2 motors

Description L298N is a kind of high voltage, high current motor driver chip produced by ST company. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V), large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on. Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well. Features： Using L298N made by ST company as the control chip,the module has such characteristics as strong driving  ability, low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage  of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability Specification Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logical current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Size:mm Applied cases: 1) Driving stepper motor The connection of driving a common 4 line 2 phase electric motor is shown