Motor drive

DESCRIPTION Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for Arduino 1. L298N as main chip, ST corporation production. 2. Low heat,outstanding anti-interference performance. 3. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power 25w. 4. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. 5. Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply. 6. Large capacity filter capacitance,afterflow protection diode, more stable and reliable. o Specifications: 2. Double H bridge drive 3. Chip: L298N (ST NEW) 4. Logical voltage: 5V 5. Drive voltage: 5V-35V 6. Logical current: 0mA-36mA 7. Drive current: 2A(MAX single bridge) 8. Size:43 x 43 x 26mm 9. Max power: 25W 10. Net weight: 25g Uses: 11. Driving stepper motor: The connection of driving a common 4 line 2 phase electric motor is shown in figure after enable ENA ENB Input the following driving timing from IN1-IN4-then the speed and direction of the stepper motor can be controlled. 12. Driving DC motor: Because this module is driven by double H bridge,it can drive two motors simultaneously. after enable ENA ENB You can input the speed and direction of PWM signal drive motor 1 from IN1 IN2 You can input the speed and direction of PWM signal drive motor 2 from IN1 IN2 We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

DESCRIPTION L293D Arduino Official Motor Drive ShieldHere is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects. 2 connections for 5V hobby servos connected to the Arduino s high-resolution dedicated timer no jitter! 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 36VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. Pull down resistors keep motors disabled during power-up Big terminal block connectors to easily hook up wires (AWG) and power Arduino reset button brought up top 2-pin terminal block and jumper to connect external power, for seperate logic/motor supplies Tested compatible with Arduino Mega, Diecimila & Duemilanove Download the easy-to-use Arduino software library, check out the examples and you re ready to go! The motor drive, can also drive 4 dc motor can be 600MA through each motor, motor can be run in to the 36V voltage between 4.5 V.Can also drive two stepper motor and two steering gear. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

    Other Items Feedbacks About Us Contact Us Add To Favorites   CNB353 - New Original L298N H-Bridge Motor Driver IC for DC,Stepper Motor Drive Make your own DC,Stepper motor Drive/CNC drive Circuit Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

Dual H Bridge L298N DC Stepper Motor Drive Controller Specification: Double H bridge drive Chip: L298N (ST NEW) Logical voltage: 5 V Drive voltage: 5 V-35 V Logical current: 0 mA-36 mA Drive current: 2 A (MAX single bridge) Max power: 25 W Size:43 x 43 x 26 mm Net weight: 25 g Package weight:36 g Note: This module has a built-in 5 V power supply, when the driving voltage is 7 V-35 V, this supply is suitable for power supply DO NOT input voltage to +5 V supply interface, however ledding out 5 V for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 Lowest on | Imported | Till stocks last

Description Package Includes: 1 Piece new  Dual H Bridge DC Stepper Motor Drive Controller Board Module Arduino L298N D2

Description L298N is a kind of high voltage, high current motor driver chip produced by ST company. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V), large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on. Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well. Features： Using L298N made by ST company as the control chip,the module has such characteristics as strong driving  ability, low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage  of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability Specification Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logical current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Size:mm Applied cases: 1) Driving stepper motor The connection of driving a common 4 line 2 phase electric motor is shown

L293D Arduino multi-motor control shield for arduino UNO Compatible with UNO, Mega, Diecimila & Duemilanove Product Summary:   ·         The shield contains two L293D motor drivers and one 74HC595 shift register. ·         The shift register expands 3 pins of the Arduino to 8 pins to control the direction for the motor drivers. ·         The output enable of the L293D is directly connected to PWM outputs of the Arduino. ·         The Motor Shield is able to drive 2 servo motors, and has 8 half-bridge outputs for 2 stepper motors or 4 full H-bridge motor outputs or 8 half-bridge drivers, or a combination.   Description: ·         2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter!  ·         Up to 4 bi-directional DC motors with individual 8-bit speed selection (about 0.5% resolution)  ·         Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.  ·         4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, 4.5V to12V  ·         Pull down resistors keep motors disabled during power-up  ·         Big terminal block connectors to easily hook up wires (AWG) and power  ·         Arduino reset button brought up top ·         2-pin terminal block to connect external power, for seperate logic/motor supplies  ·         compatible with UNO,Mega, Diecimila, & Duemilanove ·         Dimensions: 69mm x 53mm x 14.3mm (2.7in x 2.1in x 0.6in)   Package Include: ·         1pc. L293D Arduino multi-motor control shield Shipping Details: Our preferred shipping partners are for remote locations we prefer Indian speed post   Feedback: ·         In case you find any problem

L293D is a monolithic integrated, high voltage, high current, 4-channel driver,you can use DC motors and power supplies of up to 36 Volts, the L293D chip is also known as a type of H-Bridge,which is typically an electrical circuit that enables a voltage to be applied across a load

CNB353 - New Original L298N H-Bridge Motor Driver IC for DC,Stepper Motor Drive Make your own DC,Stepper motor Drive/CNC drive Circuit Please Clear Any Doubts "BEFORE" Buying any products form us. Images are for reference only  Fast Shipping via*   * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post Please Click on Images to View

This is driving module is a common DC motor, using 293D chip low current DC motor drive chip. Pins are made of Arduino compatible, also facilitate the lovers rapid development based on Arduino. 2 5V servo motor (servo) port to the Arduino high resolution and high precision timer - no jitter! 1, as many as 4 bidirectional DC motor and 4 PWM speed (approximately 0.5% of the resolution) 2, as many as 2 stepper motor control, single / double step control, staggered or subdivided and rotation angle control. 3, 4: L293D H- bridge chip each Luqiao.0.6A (peak 1.2A) current and a thermal power protection, 4.5V to 36V. 4, pull down resistor maintain the motor stop status

Package Contents 1 x L298N DC Driver Controller Stepper Motor smart Car Board Module Dual H Bridge DC Motor Driver Arduino PIC, Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC    Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V    Driven part of the peak current Io: 2A    The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)    The logical part of the operating current range: 0 ~ 36mA    Storage temperature: -25 Deg C ~ +130 Deg C    Other Extensions: control of direction indicators, the logic part of the plate to take power interface. Driver Board Size: 55mm * 60mm * 30mm    Drive plate Weight: 33g    Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.     Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC   Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V   Driven part of the peak current Io: 2A   The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)   The logical part of the operating current range: 0 ~ 36mA   Storage temperature: -25 Deg C ~ +130 Deg C   Other Extensions: control of direction indicators, the logic part of the plate to take power interface.Driver Board Size: 55mm * 60mm * 30mm   Drive plate Weight: 33g   Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.

Step into motor usually defines has step from corner or step number parameter, General of motor a go are is is divided into 200 step, is step from corner for 1.8 degrees, EasyDriver has step from subdivision features, this paragraph drive Board of fine is divided into 8 subdivision, is will motor of each step again fine is divided into 8 step, such can can get more precise of control, that is EasyDriver needs step to completed a full of 360 degrees rotating. Ms1 and MS2 is a stepping motor subdivision resolution selection logic input port; Dir is the choosing of motor operation; Reset to reset the chip initializer and block all external output; Step pulse input ports; Out1a, out1b, out2a, and out2b into two h bridge on the output port; Enable to enable; Sleep sleep mode; Sense1, sense2 for h-bridge current detecting resistors; REF is the reference voltage; GND for logic and power; RC1, RC2 for the h-bridge is a fixed deadline for analog inputs. Aslb is United States Allegro produced micro-step PWM constant current control of two-phase stepping motor driven dedicated drive. Its operating voltage up to 30v, current up to 750ma, one aslb driving a two phase stepping motor enables 8 subdivision driving. Chip internal PWM current control circuit can be set through PFD voltage for slow and fast, mixing three current decay modes, if the PFD-side voltage is higher than 0.6vdd, slow decay mode is selected. Below the 0.21vdd, fast decay mode is selected. Mixed decay modes between the two. In addition, aslb provides perfect protection measures, including the transient voltage, overheat protection, preventing current passthrough, under-voltage lock function. Aslb and does not require additional interface circuitry between the microprocessor, the chip-production easystepper Interface, 8 control lines was reduced 2 (step size and direction), you simply enter the control pulses for stepper motor, embedded converters for stepping motor control can be achieved. Aslb need a few resistors and capacitors to adjust its parameters throughout the driving circuit is very simple. Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Step into motor usually defines has step from corner or step number parameter, General of motor a go are is is divided into 200 step, is step from corner for 1.8 degrees, EasyDriver has step from subdivision features, this paragraph drive Board of fine is divided into 8 subdivision, is will motor of each step again fine is divided into 8 step, such can can get more precise of control, that is EasyDriver needs 1600 step to completed a full of 360 degrees rotating. Ms1 and MS2 is a stepping motor subdivision resolution selection logic input port; Dir is the choosing of motor operation; Reset to reset the chip initializer and block all external output; Step pulse input ports; Out1a, out1b, out2a, and out2b into two h bridge on the output port; Enable to enable; Sleep sleep mode; Sense1, sense2 for h-bridge current detecting resistors; REF is the reference voltage; GND for logic and power; RC1, RC2 for the h-bridge is a fixed deadline for analog inputs. A3967slb is United States Allegro produced micro-step PWM constant current control of two-phase stepping motor driven dedicated drive. Its operating voltage up to 30v, current up to 750ma, one a3967slb driving a two phase stepping motor enables 8 subdivision driving. Chip internal PWM current control circuit can be set through PFD voltage for slow and fast, mixing three current decay modes, if the PFD-side voltage is higher than 0.6vdd, slow decay mode is selected. Below the 0.21vdd, fast decay mode is selected. Mixed decay modes between the two. In addition, a3967slb provides perfect protection measures, including the transient voltage, overheat protection, preventing current passthrough, under-voltage lock function. A3967slb and does not require additional interface circuitry between the microprocessor, the chip-production easystepper Interface, 8 control lines was reduced 2 (step size and direction), you simply enter the control pulses for stepper motor, embedded converters for stepping motor control can be achieved. A3967slb need a few resistors and capacitors to adjust its parameters throughout the driving circuit is very simple. Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

DC Motor / Stepper Driver H Bridge Controller This motor driver is perfect for robotics and mechatronics projects for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms, etc. This is a medium power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L293 motor driver IC. It can drive 4 DC motors on and off, or drive 2 DC motors with directional and speed control. The driver greatly simplifies and increases the ease with which you may control motors, relays, etc from microcontrollers. It can drive motors upto 36V with a total DC current of up to 600mA. You can connect the two channels

THIS L293D DRIVER MODULE IS A MEDIUM POWER MOTOR DRIVER PERFECT FOR DRIVING DC MOTORS AND STEPPER MOTORS. IT USES THE POPULAR L293D MOTOR DRIVER IC. IT CAN DRIVE 4 DC MOTORS IN ONE DIRECTION, OR DRIVE 2 DC MOTORS IN BOTH THE DIRECTIONS. FEATURES AND USAGE L293D motor driver IC. Male burg stick connectors for supply, ground and input connection Screw terminal connectors for easy motor connection This motor driver is perfect for robotics and mechatronics projects for controlling motors from microcontroller, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms

DC Motor / Stepper Driver H Bridge Controller This motor driver is perfect for robotics and mechatronics projects and perfect for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms, etc This is a high power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L298 motor driver IC and has onboard 5V regulator which it can supply to an external circuit. It can control upto 4 DC motors, or 2 DC motors with directional and speed control It can drive motors upto 46V with a total DC current of up to 4A. You can connect the two channels

L293D Motor Driver ICs Plus 2  16 Pin IC Base. *** MUST HAVE FOR STUDENTS  AND HOBBYIST ***  The L293D is designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 36 V.  They are designed to drive inductive loads such as relays, solenoids, dc and bipolar stepping motors,  as well as other high-current/high-voltage loads

it is a variable frequency drive to control speed of three phase induction motor. It is for last year electrical students. i will give all required reports like last year both semester final report + ppr + psar +ieee format +canvas + ppt,etc.For any query u can call me.

Description Package Includes: 1 Piece new  5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN Line 4 Phase It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91    between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

  Description Package Includes: 1 Piece new  5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN2003 5 Line 4 Phase It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91  9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

New L293D motor shield, the input voltage DCV 600mA OUTPUT CURRENT CAPABILITY PER CHANNEL 1.2A PEAK OUTPUT CURRENT (non repetitive)PER CHANNEL ENABLE FACILITY OVERTEMPERATURE PROTECTION LOGICAL "0" INPUT VOLTAGE UP TO 1.5 V(HIGH NOISE IMMUNITY) INTERNAL CLAMP DIODES The Device is a mnolithic integrated high voltage,high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoides, DC  and stepping motors) and switching power transistors.To simplify use as two bridges each pair of channels is equipped with an enable input. A separate supply input is provided for the logic, allowing operation at a lower voltage and internal clamp diodes are included. This device is suitable for use

Never run out of space for all your photos, videos, and files with unlimited storage plans from Amazon Cloud Drive Item specifics Condition: BRAND NEW SEAL PACKED: Form Factor: 3.5" Storage Capacity: 500GB Brand: Seagate Interface: SATA   9GW Seagate Pipeline HD.GB RPM SATA 3Gbps 8MB Cache 3.5-inch Internal Hard Drive Mfr P/N 9GW Hard Drives Best-Fit Applications include DVR and media center applications, Low-power appliances and devices, Home theater PC, IPTV, Multimedia hard drive recorders and Karaoke and audio jukeboxes Tuned to balance high-performance with low power consumption, Pipeline HD drives can support a minimum of 10 simultaneous streams of HD content Best-in-class power performance is easy on the environment while also enabling strict energy conservation programs such as Energy Star Designed for cool, quiet, worry-free, 24x7 operation 365 days a year. Always on, always reliable Seagate Think Green sustainability goes beyond green with improved reliability, low power consumption, leading environmental compliance programs, RoHS and low-halogen compliance. Best-in-class power performance is easy on the environment while also enabling strict energy conservation programs such as Energy Star Seagate SoftSonic motor technology enables years of ultra-quiet, worry-free operation with acoustic performance as low as 1.9bels Ships

PCA Channel 12-bit PWM Servo motor Driver I2C Module Arduino PIC Robot WC You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs • It's an i2c-controlled PWM driver with a built

PCA9685 16 Channel 12-bit PWM Servo motor Driver I2C Module Arduino PIC Robot WC You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs • It's an i2c-controlled PWM driver with a built

Product Description Description: Double H bridge drive Chip: L298N  Logical voltage: 5V Drive voltage: 5V-35V Logical current: 0mA-36mA Drive current: 2A (MAX single bridge) Storage temperature: -20 to +135 Max power: 25W Weight: 30g Size: 43 x 43 x 27mm

4 Wheel Robotic Platform V2.0 (4x4 Drive) DIY for projects The package includes -  300 rpm motor (12v dc) - 4pcs Chasis for Robot - 1 pc Wheel 7cm x 4cm - 4pcs Please note - battery would have to be separately purchased and will not be included

4 Wheel Robotic Platform V4.0 (4x4 Drive) DIY for projects The package includes -  300 rpm motor (12v dc) - 4pcs Chasis for Robot - 1 pc Wheel 10cm x 4cm - 4pcs Please note - battery would have to be separately purchased and will not be included

All type of panel manufacturers lift panel, ac/DC motor panel etc...some panel prices is negotiable concate now

Signal Output function: Brand new and high quality. Voltage: 5V. Diameter: 28mm. Step angle: x 1 / 64. Reduction ratio: Line 4 phase can be driven by ordinary uln chip can also be connected