Amplifier pcb watt pa

PCB for High power output PA Series Amplifier, provides superb & Power full sound quality. With  2SCSA output devices the amp will put out close to 400 WATTS @ 8 OHMS and 800 Watt @ 4 OHMS.  Size 94 mm X 260 mm. FR4 Glass epoxy 1.6 mm THK Board 70  Microns copper. Included Schematic & BOM. Qty- 02 Nos. (TWO ONLY) PCB. FOR STEREO Note:- Amplifier Output Power 400 Watt @ 8 Ohms and 80 Watt @ 4 Ohms. We also offer Power Supply Board for this amplifier kit (4 x uf 100 Volt ELNA Capacitors Rs. only) Contact details:- E-Mail: Mob. No.

This is a high-quality PCB (printed circuit board) for TI LM4780 60 watts + 60 watts stereo audio amplifier IC. You can build a very high-quality professional Audio Amplifier at a fraction of the cost of Commercial Amplifiers. The board is without parts and IC. This is a stereo PCB. You can buy audio IC from the market. If you need parts also please let me know. Thanks

High power output for PA system and DJ system, output devices (2SCSA) the amp will put out close to 350 Watts @ 8 Ohms, 550 Watts @ 4 Ohms and 700 Watts @ 2 Ohms. Required Power Supply transformer Volts, 8 Amps (Not Included).  Kit Includes (Qty- 1 No. complete Assembled Kit with 100% original & Reputed Brands component): All resistors (1% metal film)  Power resistors (Stead) Faston connectors MJE drivers, MJE , BC and BD SC SA output transistors 9 pairs (Each Transistor come with 150 Watt). All Film & Electrolytic Capacitors (Manufacturer of Electrolytic Caps- Keltron & Samsung and Manufacturer of Film Caps- Wima, Kemet & Muratta) MAIN HEAT SINK INCLUDED. Contact details:- E-Mail: Mob. No.

High power output for PA system and DJ system, output devices (2SCSA) the amp will put out close to 2 x 150 Watts @ 8 Ohms and 2 x 250 Watts @ 4 Ohms. Required Power Supply transformer Volts, 10 Amps (Not Included). Kit Includes (Qty- 1 No. complete Assembled Kit with Main heat sink): All components are 100% original and reputed Brands All resistors (1% metal film) (Manufacturer:- Thakor / Watts) Power resistors  (Manufacturer:- El. cr ) Fastron connectors Silpad insulators Silver Mica compensation capacitors (Manufacturer:Kemet/ACE) MJE drivers (Manufacturer: On Semiconductor) 2SCSA output transistors. Electrolytic Capacitors (Manufacturer: Keltron) Note:- Amplifier Output Power 2 x 150 Watt @ 8 Ohms and 2 x 250 Watt @ 4 Ohms (Power supply: Volt 10 Amps)  Contact details:- E-Mail: Any Query Please call on: Mob. No. 

High power output for PA system and DJ system, output devices (2SCSA) the amp will put out close to 350 Watts @ 8 Ohms, 550 Watts @ 4 Ohms and 700 Watts @ 2 Ohms. Required Power Supply transformer Volts, 7 Amps (Not Included).  Kit Includes (Qty- 1 No. complete Assembled Kit with 100% original & Branded components): All resistors (1% metal film)  Power resistors (CRC) Faston connectors MJE drivers, MJE , BC and BD SC SA output transistors 9 pairs (Each Transistor come with 150 Watt). All Film & Electrolytic Capacitors (Manufacturer of Electrolytic Caps- Keltron & Samsung and Manufacturer of Film Caps- Wima, Kemet & Muratta) Main Heat Sink required (100 mm x 260 mm x 32 mm - 1 No.) - NOT INCLUDED. Note:- Amplifier Output Power 350 Watt @ 8 Ohms and 550 Watt @ 4 Ohms (Power supply: Volt 7 Amps) We also offer Power Supply Board for this amplifier kit (4 x uf 100 Volt ELNA Capacitors,) Rs./- Shipping charge extra. Contact details:- E-Mail: Mob. No.:

ESP is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functi ons from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. Corresponding Interface: SDIO 2.0, SPI, UART 32-pin QFN package Integrated RF switch, balun, 24dBm PA, DCXO, and PMU Integrated RISC processor, on-chip memory and external memory interfaces Integrated MAC/baseband processors Quality of Service management I2S interface for high fidelity audio applications On-chip low-dropout linear regulators for all internal supplies Proprietary spurious-free clock generation architecture Integrated WEP, TKIP, AES, and WAPI engines Specification: b/g/n Wi-Fi Direct (P2P), soft-AP Integrated TCP/IP protocol stack Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLLs, regulators, DCXO and power management units +19.5dBm output power

Firmware Details: Version: ESP-01 Firmware:0.9.4 Default Baudrate: (configurable) VCC:3.3v Logic level:3.3v   The SOC has Integrated TCP/IP protocol stack.   ESP is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.   ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.   Corresponding Interface:     SDIO 2.0, SPI, UART     32-pin QFN package     Integrated RF switch, balun, 24dBm PA, DCXO, and PMU     Integrated RISC processor, on-chip memory and external memory interfaces     Integrated MAC/baseband processors     Quality of Service management     I2S interface for high fidelity audio applications     On-chip low-dropout linear regulators for all internal supplies     Proprietary spurious-free clock generation architecture     Integrated WEP, TKIP, AES, and WAPI engines   Specification:     b/g/n     Wi-Fi Direct (P2P), soft-AP     Integrated TCP/IP protocol stack     Integrated TR switch, balun, LNA, power amplifier and matching network     Integrated PLLs, regulators, DCXO and power management units     +19.5dBm output power

ESP serial Wi-Fi UART wireless IOT module 3.3V AP+STA   For RasPi, arduino, AVR, other MCU ESP serial wifi Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.   Product Description esp serial wifi:   ESP is a highly integrated chip designed for the needs of a new connected IoT world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. Note:   This module requires a 3.3V supply for VCC, and 3.3V logic. It is not 5V tolerant. Connecting Rx or Tx on 5V Arduino may destroy this module. You must use a logic level converter, or a 3.3V Arduino. Also the 3.3V supply on the Arduino Uno has inadequate current capability to power this module. You must provide a separate, higher 3.3V supply (about 300mA or better)   Features ESP serial wifi: ·         SDIO 2.0, SPI, UART ·         Integrated RF switch, balun, 24dBm PA, DCXO, and PMU ·         Integrated RISC processor, on-chip memory and external memory interfaces ·         Integrated MAC/baseband processors ·         Quality of Service management ·         I2S interface for high fidelity audio applications ·         On-chip low-dropout linear regulators for all internal supplies ·         Proprietary spurious-free clock generation architecture ·         Integrated WEP, TKIP, AES, and WAPI engines   Specification ESPEX: ·             b/g/n ·             Wi-Fi Direct (P2P), soft-AP ·             Integrated TCP/IP protocol stack ·             Integrated TR switch, balun, LNA, power amplifier and matching network ·             Integrated PLLs, regulators, DCXO and power management units ·             +19.5dBm output power