Apm

APM Mount Plate Specifications Returns In case Product is faulty Buyer must notify us within 24 hours of delivery time and can return within 2 days for a Replacement Or Refund. Returns will be accepted only when products are sent

Introduction: This is the new APM 2.6 autopilot module. The sensors are exactly the same as with APM2.5+, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers. The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors. This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility

Note: This is a clone of original and its approved by DIYDRONES themselves. This is APM 2.6 (compass not on board) The ArduPilot Mega 2.52 is a complete open source autopilot system and the bestselling technology that won the prestigious Outback Challenge UAV competition. This version is ready to use, with no assembly required. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it’s often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility

Pixhawk/APM Telemetry Module 433Mhz   Notice:The module is OEM version,not 3DR manufactured Description: Very good quality design,as you can see as the picture. Support OTG of  Android Cellphones,and computer OTG. -PLUG AND PLAY. Pre-configered and tested to BAUD rate, and all other settings needed. -I preprogram these radios to the correct bod rate so you can just connect them to your quadrino and start chaning PID's on the fly. - The telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. It's availabl

NEO-6M Ublox u-blox GPS Module with on-board compass HMCl (compass) (mag)   Specification: - tracking sensitivity:-161dBm - Capture sensitivity:-148dBm - cold start time:38s average - Warm start time:35s average - hot start time:1s average - Capture time:0.1s Average - Temperature:40   to +80 - wide power supply voltage:+3.5V~+5.5V   Ublox GPS Module V2.0     Description: - Main chip:U-BLOX NEO-6M - C/A code,MHz - Receiver Frequency:LMHz] - Locate performance - 2D:3m(Average) - 2D:2m(average),with WAAS - drifting - accuracy:1us - coordinate system:WGS-84 - max attitude height: - Max speed:515m/s - accerlaration:     Super Bright LED BlackPlane with Standard Mk style mounting holes 45mm X 45mm Blox Neo 6M Chipset bps (Default) Changed to bps ! Output GGA, GSA and RMC frames 1Hz (Default) Changed to 5Hz! Permanent Configuration Retention Cable included + Bigger battery + compass on board + 6 pin connector for EZ connect to MEGA BLACK + 4 pin connector for onlyGPS use + 4 pin connecton for compass only use + GPS "PCB HOOD" for More EMI/RFI Shielding     Packages Including:   1pcs * 6M GPS With Shell

NEO-6M Ublox u-blox GPS Module with on-board compass HMCl (compass) (mag)   Specification: - tracking sensitivity:-161dBm - Capture sensitivity:-148dBm - cold start time:38s average - Warm start time:35s average - hot start time:1s average - Capture time:0.1s Average - Temperature:40   to +80 - wide power supply voltage:+3.5V~+5.5V   Ublox GPS Module V2.0     Description: - Main chip:U-BLOX NEO-6M - C/A code,MHz - Receiver Frequency:LMHz] - Locate performance - 2D:3m(Average) - 2D:2m(average),with WAAS - drifting - accuracy:1us - coordinate system:WGS-84 - max attitude height: - Max speed:515m/s - accerlaration:     Super Bright LED BlackPlane with Standard Mk style mounting holes 45mm X 45mm Blox Neo 6M Chipset bps (Default) Changed to bps ! Output GGA, GSA and RMC frames 1Hz (Default) Changed to 5Hz! Permanent Configuration Retention Cable included + Bigger battery + compass on board + 6 pin connector for EZ connect to MEGA BLACK + 4 pin connector for onlyGPS use + 4 pin connecton for compass only use + GPS "PCB HOOD" for More EMI/RFI Shielding     Packages Including:   1pcs * 6M GPS With Shell 1pcs * mounting bracket

APM 2.6 Flight Controller With 6M GPS For RC Multicopters pls before buying make sure you know how to install on multirotor this is finest product available

Features: Deans Plug Max input voltage: 30V Max current sensing: 90A Voltage and current measurement configured for 5V ADC Switching regulator outputs 5.3V and 3A max 6P molex cable plugs directly to APM Arduflyer 2.5 s PM connector Specifications: Package size: cm in Package weight: 24g 0.8oz Package list: 1 APM Power Module V1.0 Output BEC 3A Deans T Plug

GadgetsDealIndia Other Items Feedbacks About Us Contact Us Add To Favorites APM2.6 ArduPilot Mega External Compass APM Flight Controller Board w/GPS for Multicopter Fixed-wing Copter

Description  Latest NEO-6 V3.1 GPS NEO-6M Module for APM MWC Pirot Rabbit Flight Controller Features: NEO - 6 GPS v3.1 main features:   (1)  Imported brand too large size au 25 x 25 mm ceramic antenna, with low noise amplifier and filter combination into ublox official recommended best performance combination plan, there is a big signal reflection area, make the signal sensitivity is better than the previous version.    (2)   Onboard parameters saved

Package includes:  1x top plate 1x bottom panel  4x damping ball.   Pixhawk damping seat, the top contour matching Pixhawk shell shape, APM can also fit

This Radio Telemetry kit offers a great low price, longer range (approx. 1.5km with supplied antennas) and superior performance. The system utilises the 915Mhz band and provides a full-duplex link using HopeRF's HM-TRP modules running custom, open source, firmware. The SiK firmware includes a boot loader that permits radio firmware upgrades over the serial interface, and configuration of system parameters. Firmware upgrades and configuration are fully supported

ArduPilot Mega APM 2.6 The ArduPilot Mega 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious Outback Challenge UAV competition. This version is ready to use, with no assembly required. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints.   This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility

Description: – The newest high precision GPS with electronic compass, small volume mm dimension – Suitable for flight control such as  APM, Pixhawk, Jade Rabbit, MWC Specification: – With shell, the cables are fixed and cannot be moved, can connect with Pixhawk hardware – Internal core of new version surpasses 6M, compare favourably with 6H – Cold start positioning time is less than 40 seconds – Warm start positioning time is less than 5 seconds – Positioning accuracy is 2m – NEO-7N is of high performance, quick research, high positioning precision, very rstable

More info The all new HK PilotMega 2.7 is a fresh look and a revamp of the popular APM based flight controller. Over the course of the ArduPilot project and development of the Open Source 2.5 platform, some known issues and ergonomic challenges have been noted. The goal of the HK PilotMega 2.7 was to fix and improve upon this great platform, giving back to the community a design that is improved and stable and yet reasonable priced, making this super powerful Flight controller a great fiscal option to the 32bit variants. There are 5 major improvement

Recommended Setup Motor  HKV  HKV ESC 10A ESC 12A ESC Propeller:  5inch or 6inch Radio & Receiver:  4CH or More Flight Controller CC3D Flip32  or  Flip32+ APM Mini KK 2.1  etc.. Battery: 3S or 4S mAh - mAh Specification Frame Weight: Approx 102g FC Mounting Hole: There is no default mounting holes for flight controller so you need to make the holes by yourself.  Battery Strap Gap: 20mm @ M3 Front Servo Mount: 23.5x13.5mm Suitable for servos eg. SG90, MG90S etc... size servos Motor Mounting: M Suitable) Package 1 x RCX FPV260 Quad Copter A Mini Sized FPV Multi-Rotor (Barebone / Nylon Material) 1 x Set of Screw