Atmega board

From Arduino to a Microcontroller on a Breadboard  Minimal Circuit (Eliminating the External Clock) No components are needed to run the microcontroller, just power it up and program using any USB-ISP, FTDI breakout board or programmer. Very useful for projects. Full technical support will be provided to run the  bare-minimum  arduino.  (DEMO IMAGE MICRONTROLLER RUNNING THE LCD)     NOTE - PRICE IS OF ONE ATMEGA 328P-PU MICROCONTROLLER (RUNS WITHOUT OSCILLATOR & R-C COMPONENTS)               ARDUINO PROGRAMMABLE.  

2 Pcs (One pair) ATMega R3 Compatiable Microcontroller Board with Free USB Cable of Arduino This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality.  100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

Arduino mega r3 development board with ATmega + ATmega16U2 with USB cable Arduino mega clone based on current open source hardware atmega atmega16u2 arduino mega best quality Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.     Product Summary Mega : ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz

Arduino mega r3 development board with ATmega + ATmega16U2 with USB cable Arduino mega clone based on current open source hardware atmega atmega16u2 arduino mega best quality 1 set or ARDUINO MEGA R       Product Summary Mega : ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz

With this board you can develop and prototype with ATMEGA16/ATMEGA pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters.   FEATURES AVR Development Board for Atmel ATMEGA ISP Socket for Flashing On board Regulated Power Supply 5v,12v supplys Easy to test with Burg Connecters wires An RS232 Serial Port 7Seg Mulitplexed Display DC Power Supply Connector(12v Ac or Dc) READY INTERFACE For LCD display 2linex16Character 24Cxx (I2C) (EEPROM) RTC (DS LED array Matrix Key Pad 4 Interrupt Switches +12v Relay (one) Package Content   AVR Development Board (WITH CHIP MAX232) Burg Connecters 20 Nos Female to Female.

Product Description: 20 Digital Input / Output. Tx, Rx, D2~D13, A0~A5. 8 Analogue Inputs. A0~A7. 6 PWM Ports. D3, D5, D6, D9, D10, D11. Arduino-compatible Board. ATmega328 running at 16MHz with external resonator (0.5% tolerance) USB connection off board (Supports Serial Download) Supports auto-reset Max 150mA output Over current protected Reverse polarity protected DC input 5V up to 12V On board Power and Status LEDs Dimensions（Long）33mm *（wide）18 mm *（high）6mm Package Content: 1x Arduino Pro Mini Atmega 328P board  3PCS Gilded Pin

Why to buy  Pro Mini ATMEGA168  ? When you get Pro Mini Atmega328P. 32KB of Program Memory + 2KB SRAM + Byte EEPROM Product Description: 20 Digital Input / Output. Tx, Rx, D2~D13, A0~A5. 8 Analogue Inputs. A0~A7. 6 PWM Ports. D3, D5, D6, D9, D10, D11. Arduino-compatible Board. ATmega328 running at 16MHz with external resonator (0.5% tolerance) USB connection off board (Supports Serial Download) Supports auto-reset Max 150mA output Over current protected Reverse polarity protected DC input 5V up to 12V On board Power and Status LEDs Dimensions（Long）33mm *（wide）18 mm *（high）6mm Package Content: 1x Arduino Pro Mini Atmega 328P board  3PCS Gilded Pin

LilyPad 328 ATmega328P Main Board compatible with Arduino’s IDE Features: Brand new and high quality The LilyPad Iduino is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The LilyPad Iduino can be programmed with the software. The ATmega328V on the LilyPad comes preburned with a bootloader that allows you to upload new code to it with the software. You can also bypass the bootloader and program the ATmega through the ICSP (In-Circuit Serial Programming) header. The LilyPad should only be programmed with software versions 0010 or higher. You can program it with earlier versions, but all of the time related functions will be switched off (making them twice as slow as they should be). Warning: Do not power the LilyPad with more than 5.5 volts, or plug the power in backwards: you'll kill it. 328 Main board; The Digital I/O Digital input/output terminal, a total of 0 ~ 13; The Analog I/O Analog input/output terminal, a total of 0 ~ 5; Support the ISP download function; Support the TX/RX terminals; Support the AREF terminals; Support the six groups of PWM terminal (Pin11 Pin10, Pin9, Pin6 and Pin5, responsible); The input voltage: 3.3 V DC; Using Atmel Atmega328V - 20 pu microcontroller; Specifications: Microcontroller: ATmega328V Operating Voltage: 2.7-5.5 V Input Voltage: 2.7-5.5 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 6 DC Current per I/O Pin: 40 mA Flash Memory: 16 KB (of which 2 KB used by bootloader) SRAM: 1 KB EEPROM: 512 bytes Clock Speed: 8 MHz Package includes: 1* LilyPad atmega 328 Main board Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Arduino mega r3 development board with ATmega & CH340G Arduino clone based on current open source hardware   Product Summary arduino mega:   ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz

Arduino mega r3 development board with ATmega & CH340G Arduino clone based on current open source hardware Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.     Product Summary:   ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz

Mega R3 Compatiable Microcontroller Board ATmega USB Cable of Arduino This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality.  100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

    Other Items Feedbacks About Us Contact Us Add To Favorites   Set of 5 Pcs AVR28 Base Board  Kit.  For Electronic project.   CNB009 - Development Board For ATmega8,168,328,5 Pc Kit Electronics DIY Projects Atmel AVR - 28 Pin Base Boar d  -  1 Pcs (For ATmega8 ,ATmega 168,ATmega 328 Microcontroller)  **FREE**    10 Wire FRC Cable -  3 Pcs **FREE**    12V 1Amp SMPS -  1 Pc ** Does not Include Any Microcontroller ** ****FREE**** 3 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm.   ,with female connectors on both ends. Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

This MEGA BOARD is a 100% compatible derivative of current R3 Arduino MEGA This is an Arduino Clone based on current open source hardware We are not affiliated with Arduino.cc IMPORTED HIGH QUALITY FAST SHIPPING WITHIN 3-7 WORKING DAYS 100% TESTED & SATISFACTION GUARANTEED CASH ON DELIVERY AVAILABLE If you want  3.2'' TFT Touch Shield for Mega compatible please Click Here Item description: Compared to the old version, R3 version major changes: Atmega 16U2 chip alternative 8U2. Means a higher transfer rate and memory. without having to install the driver

From Printer Type(Type B) USB connector to micro USB connector Replace the expensive FTDI FT232RL IC to CH340 IC. Replace the main IC atmega 328 PTH to atmega SMD QFP with arduino uno bootloader. Reserved extra male pins holes, so both female and male pins available on board, with some extra useful pins. Reserved another 2×4 pin holes, next to ISCP, pins includes: TX, RX, VCC, GND, IIC-SCL, IIC-SDA, power pins All the rest features are kept the same as the official version.   First Download the CH340 Driver from http://wch.cn/downfile/195 or http://kiguino.moos.io/downloads/CH341SER_MAC.ZIP or https://www.dropbox.com/s/o2a5vntk7n5y7hi/CH341SER.zip?dl=0

1 Piece Arduino Mega R3 Compatible (Clone) USB Board - ATmega CH340 with USB Cable Order more than one piece to save shipping cost. You can contact us at +91- for any question or concern. Device Details This device and other listings with words 'Compatible' and 'Developement'

KKmulticopter V5.5 controller blackboard Quadcopter + USB Programmer + Signal Distribution Board Description: The KKmulticopter is a KK flight controller board for remote control multicopters with 2,3,4 and 6 rotors. We get KKmulticopter to stablise the aircraft during flight. KK flight controller takes the signal from the three gyros on the board (roll, pitch and yaw) and feeds the information into the Integrated Circuit (Atmega IC). KK flight controller then processes the information according the the KK software and sends out control signal to the Electronic Speed Controllers (ESCs) which are plugged onto the board and also connected to the motors. Depending the signal from the IC the ESCs will either speed up or slow down the motors (and tilt the rear rotor with a servo

Arduino uno r3 development board with ATmega328p CH340G Arduino clone based on current open source hardware Arduino uno Atmega 328p smd ideal for prototyping Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.   Product Summary arduino uno: ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz         Features of arduino uno: ·         Replaced the expensive 16u2 with CH340G chip to avoid the driver compatibility problem which was found on some win7/win8 OSes. ·         Increased the extra pin holes to facilitate the use of DuPont line cables, with some extra useful pins. ·         Extra 3x4 pin holes, next to ICSP connector, which includes Tx, Rx, 5v, 3.3v, ground, SDA and SCL.    ·         All the rest features are kept the same as the official version   Driver installation and usage procedure: · Install   CH340G driver  . ·     Install   Arduino IDE   ß   (click here) ·     Connect the board to computer. ·     Launch Arduino IDE, select board as “arduino uno” ·     Select the com port OS created for the card(control panel   à   device manager) ·     Open basics   à   blink sketch and upload. ·     If you find any difficulty you can contact us, contact details are given below.   Factory Testing Procedure for arduino uno Atmega328p: We will make sure that we have tested the product with following procedure before shipment ·   We have uploaded blink program with 2 second blinking rate of LED ‘L’ instead of 1second default rate. ·   You can check it at the time of receipt of the product. Just connect it to the USB port of any device and the ‘L’ LED will blink at the rate of 2 second.   Package Include arduino uno: ·   1 x   arduino uno development board ·   1 x   USB cable ·   A plastic container box.   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·         In case you find any problem

Product Description:  Supports AVRDude   Support for Linux, Mac OS X and Windows  XP, pin ISP interface Supports all Atmega microcontrollers that provide the port for the plug. easily program kk board. Package includes: 1x programmer 1x ribbon cable

Arduino Mega R3 compatible board Arduino Clone based on current open source hardware Product Summary: ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz Features: v   Completely solved the traditional board that is not compatible with win7 and win8. v   Increased the pin socket, to facilitate the use of DuPont line cables. v   Replaced Atmega16u2 with CH340G which can easily communicate to Arduino IDE directly.                 Package Include: v   One piece of Arduino Mega board v   One USB cable v   A plastic container box. Shipping Details: Our preferred shipping partners are                             For remote locations we will prefer Indian speed post Feedback v     In case you find any problem

This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality. 100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

This MEGA BOARD is a 100% compatible derivative of current R3 Arduino MEGA This is an Arduino Clone based on current open source hardware We are not affiliated with Arduino.cc IMPORTED HIGH QUALITY FAST SHIPPING WITHIN 3-7 WORKING DAYS 100% TESTED & SATISFACTION GUARANTEED Contact us for Special Price if you want to buy more than 5Pieces of this item Item description: Compared to the old version, R3 version major changes: Atmega 16U2 chip alternative 8U2. Means a higher transfer rate and memory. without having to install the driver

Arduino Mega R3 compatible board BEST QUALITY AMONGST ALL OTHER ARDUINO CLONES AVAILABLE Arduino Clone based on current open source hardware   Product Description: ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

Arduino Mega R3 compatible board Arduino Clone based on current open source hardware Product Summary: ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz

This MEGA BOARD is a 100% compatible derivative of current R3 Arduino MEGA This is an Arduino Clone based on current open source hardware We are not affiliated with Arduino.cc IMPORTED HIGH QUALITY FAST SHIPPING WITHIN 3-7 WORKING DAYS 100% TESTED & SATISFACTION GUARANTEED CASH ON DELIVERY AVAILABLE Buy Original Arduino UNO R3 from  http://store.arduino.cc/index.php?main_page=product_info&cPath=11&products_id=195 Download Arduino IDE & Drivers:  http://arduino.cc/en/Main/Software No need to install any additional driver

Item description:     Compared to the old version, R3 version major changes: 1) Atmega 16U2 chip alternative 8U2. Means a higher transfer rate and memory. 2) without having to install the driver

DESCRIPTION MatLogix Arduino Uno Board with Universal Shield The ARDUINO Board (ATMEGA 8-L) is a microcontroller board based on the ATmega 8-L. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8 up to programmed as a USB-to-serial converter. Universal Shield: Features: A monolithic integrated, high voltage, high current, 4-channel driver Using this chip you can use DC motors and power supplies of up to 36 V, so that some pretty big motors and the chip can supply a maximum current of 600mA per channel Also known as a type of H-Bridge, which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping LDR (light Sensor) for detecting the intensity of light. On board Regulated Power Supply 5v,12v supplys A Serial Port DC Power Supply Connector(12v Dc) LCD display 2x16Character Extra Vcc and Gnd Pins from which you can connect different devices. Potentiometer to set the light intensity of LCD Screen. Reset Switch to reset the arduino board. Slot for TSOP sensor. Kit Content: 1 x Arduino Uno Board 1 x 16x2 LCD (Female) 1 x L293D IC 1 x LDR 1 x USB Cable We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Laptop/Bluetooth Controlled Wireless Robot Robot Controlled By Laptop over Bluetooth Wireless Protocol. PACKAGE INCLUDES: 1) A ASSEMBLED Laptop/Bluetooth Controlled Wireless Robot 2) Pre- Built Windows Application By Robosoft Labs to drive the robot (Source code won't be provided due to copyright issue)   Laptop/Bluetooth Controlled Wireless Robot IS ASSEMBLED OF FOLLOWING LISTED ITEMS: 1) TWO L TYPE BO DC MOTOR (+5V TO +12V) 2) 2 CLAMPS 3) 1 CASTOR WHEEL 4) TWO WHEELS 5) L293D BOARD (MOTOR DRIVER BOARD) 6) CHASSIS 7) BLUETOOTH RECEIVER MODULE 8) 1 AVRDUINO/ARDUINO COMPATIBLE BOARD WITH AVR'S ATMEGA 8 IC 9) CONNECTING BURG WIRES 10) TUTORIAL GUIDE TEACHING HOW TO ASSEMBLE THE ROBOT FROM SCRATCH PARTS TO A Laptop/Bluetooth Controlled Wireless Robot. 11) PRE BUILT AND BURNT Laptop/Bluetooth Controlled Wireless Robot PROGRAM IN AVRDUINO ATMEGA 8 IC 12) NUT AND BOLTS. Points to be noted: 1) This Laptop/Bluetooth Controlled Wireless Robot is ASSEMBLED BY PRE-FABRICATED PARTS. 2)  Laptop/Bluetooth Controlled Wireless Robot CHASSIS is made of PLY WOOD 3) PROGRAM CODE or HEX FILE WONT BE PROVIDED Due to Copyright Issue. 4) Power Supply for Robot: Please use Only +9V battery supply (Batteries not Included as it can't be shipped)   5) Color of Components used may vary according to availability.                        FOR ANY QUERIES OR DOUBT PLEASE CONTACT US BEFORE ORDERING                                                                       E-MAIL:                                                                       MOBILE: +91- Regards, ROBOSOFT LABS                                                                  

ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT T his Wireless robot is control by ANDROID APP with the help of BLUETOOTH Wireless Protocol. This ANDROID APP also Supports VOICE COMMANDS to drive the robot too. PACKAGE INCLUDES: 1) A ASSEMBLED ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT 2) Pre- Built ANDROID APP By Robosoft Labs to drive the robot. (APP source code/program won't be provided due to copyright issue) ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT IS ASSEMBLED OF FOLLOWING LISTED ITEMS: 1) TWO L TYPE BO DC MOTOR (+5V TO +12V) 2) 2 CLAMPS 3) 1 CASTOR WHEEL 4) TWO WHEELS 5) L293D BOARD (MOTOR DRIVER BOARD) 6) CHASSIS 7) BLUETOOTH RECEIVER MODULE 8) 1 AVRDUINO/ARDUINO COMPATIBLE BOARD WITH AVR'S ATMEGA 8 IC 9) CONNECTING BURG WIRES 10) TUTORIAL GUIDE TEACHING HOW TO ASSEMBLE THE ROBOT FROM SCRATCH PARTS TO A ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT. 11) PRE BUILT AND BURNT ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT PROGRAM IN AVRDUINO ATMEGA 8 IC 12) NUT AND BOLTS. Points to be noted: 1) This ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT is ASSEMBLED BY PRE-FABRICATED PARTS. 2)  ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT CHASSIS is made of PLY WOOD 3) PROGRAM CODE or HEX FILE WONT BE PROVIDED due to COPYRIGHT ISSUE. 4) Power Supply for Robot: Please use Only +9V battery supply (Batteries not Included as it can't be shipped) 5) Color of Components used may vary according to availability. 6) Mobile phone shown is not included

Product Description This can 2nd version of the customized arduino-compatible UNO R3 board, fully compatible with the arduino official version, but replaced some expensive parts and more extra pins lead out. Cost down but maybe better performance. Main customized features: Replace the expensive 16u2 USB-TTL IC to CH340 IC, cost nearly half, and can avoid the 16u2 driver compatibility problem which found on some win7/win8 OS. Replace the main IC atmega 328 PTH to atmega SMD QFP with arduino uno bootloader. Reserved extra male pins holes, so both female and male pins available on board, with some extra useful pins. Reserved another 3×4 pin holes, next to ISCP, pins includes: TX, RX, VCC, GND, IIC-SCL, IIC-SDA, power pins All the rest features are kept the same as the official version. Documentation: CH340 Driver can find on this page. Powered by Turbo Lister

Description: This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. The Uno R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The Uno R3 works with all existing shields but can adapt to new shields which use these additional pins. Special SMD Version:Because Atmel is moving more and more of their production capacity to surface mount ICs, the DIP packaged ATmega is becoming more and more difficult to get. To keep up with demand, we now offer the Arduino Uno R3 with an SMD ATmega. Features: ATmega328 microcontroller Input voltage - 7-12V 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs 32k Flash Memory 16Mhz Clock Speed We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/