Bits pin

Atmel ATMEGA328P Microcontroller with Arduino UNO Bootloader You Will Get:ATMEGA328P with Arduino UNO Boot-loader = 1 Features: • High-performance, Low-power Atmel®AVR® 8-bit Microcontroller • Advanced RISC Architecture – 130 Powerful Instructions – Most Single-clock Cycle Execution – 32 × 8 General Purpose Working Registers – Fully Static Operation – Up to 16MIPS Throughput at 16MHz – On-chip 2-cycle Multiplier • High Endurance Non-volatile Memory segments – 32Kbytes of In-System Self-programmable Flash program memory – 512Bytes EEPROM – 1Kbyte Internal SRAM – Write/Erase Cycles: Flash/ EEPROM – Data retention: 20 years at 85°C/100 years at 25°C(1) – Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation – Programming Lock for Software Security • Peripheral Features – Two 8-bit Timer/Counters with Separate Prescaler, one Compare Mode – One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode – Real Time Counter with Separate Oscillator – Three PWM Channels – 8-channel ADC

HT12E & HT12D Encder / Decoder ICs + 2 X 18 Pin IC Base Combo... *** MUST HAVE FOR STUDENTS  AND HOBBYIST ***  The HT 12E   Encoders are a series of CMOS LSIs for remote control system applications. They are capable of encoding information which consists of N address bits and 12 N data bits. Each address/ data input can be set to one of the two logic states. The programmed addresses/data are transmitted together with the header bits via an RF or an infrared transmission medium upon receipt of a trigger signal. The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12  series of encoders. The HT12A additionally provides a 38kHz carrier for infrared systems.     The HT 12D   Decoders are a series of CMOS LSIs for remote control system applications. They are paired with Holtek s HT 12E series of encoders (refer to the encoder/decoder cross reference table). For proper operation, a pair of encoder/decoder with the same number of addresses and data format should be chosen. The decoders receive serial addresses and data from a programmed HT 12E series of encoders that are transmitted by a carrier using an RF or an IR transmission medium. They compare the serial input data three times continuously with their local addresses. If no error or unmatched codes are found, the input data codes are decoded and then transferred to the output pins. The VT pin also goes high to indicate a valid transmission. The HT 12D series of decoders are capable of decoding informations that consist of N bits of address and 12N bits of data. Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and HT12F is used to decode 12 bits of address information. HT12E (Encoder) Features: Operating voltage: 2.4V~12V Low power and high noise immunity CMOS technology Low standby current: 0.1uA (typ.) at VDD=5V Minimum transmission word: Four words Built-in oscillator, needs only 5% resistor Data code has positive polarity Minimal external components Secure and robust protocol Ideal for remote control and security applications Compatible with the HT12D decoder IC 18-pin DIP   HT12D (Decoder) Features: Operating voltage: 2.4V~12V Low power and high noise immunity CMOS technology Low standby current Capable of decoding 12 bits of information Binary address setting Received codes are checked 3 times Address/Data number combination: 8 address bits and 4 data bits Built-in oscillator needs only 5% resistor Valid transmission indicator Easy interface with an RF or an infrared transmission medium Minimal external components Secure and robust protocol Ideal for remote control and security applications Compatible with the HT12E encoder IC 18-pin DIP Please Give Us Positive Feedback.Your Feedback is very important to us.Any doubt contact us.We are Happy to help you  

Description Remote control 1.Operating voltage: DC12V (27A/12V battery x1) 2.Operating Current: 10mA @ 12V 3.Radiated power: 10mw @ 12V 4.Modulation mode: ASK (Amplitude Modulation) 5.Transmitting frequency: 315MHZ (SAW frequency stabilization) 6.Transmission distance:M (Open field the receiver sensitivity -100dbm) 7.Encoder types: fixed code 8. The frequency of this product is 315 mhz. With decoding receiver board 1.The operating voltage DC5V, receiver sensitivity is-98db. Leg 7 bits, respectively, VT, D3, D2, D1, D0, the +5 V and GND. VT is a valid signal high output pin Upon receiving a valid signal, the pin output high, may also drive the relay. 2.Size: mm There are four buttons on the remote control, and respectively correspond to the four data bits to the receiving board output pin D0, D1, D2, and D3 of. Press the buttons transmit signals, the corresponding data bit is output high. Module function description: This module contains no self-locking function, simple implementation, wireless remote control by pressing a key, the receiver output a high level, the corresponding output when key releases. High level at the receiving end disappear, and each channel are independent of each other, each other. The output of high level can directly drive the relay, as shown

AtmegaPins 16MHz 16kb 8-bit Microcontroller FREE 40 PIN DIP SOCKET  Features High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture 131 Powerful Instructions - Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Up to 6 MIPS Throughput at 16MHz Fully Static Operation On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 16k Bytes of In-System Self-Programmable Flash Optional Boot Code Section with Independent Lock Bits 512K Bytes EEPROM Programming Lock for Software Security JTAG (IEEE std. Compliant) Interface Boundary-scan Capabilities According to the JTAG Standard Extensive On-chip Debug Support Programming of Flash, EEPROM, Fuses, and Lock Bits through the JAGS Interface Peripheral Features On-chip Analog Comparator Programmable Watchdog Timer with Separate On-chip Oscillator Master/Slave SPI Serial Interface Two 8-bit Timer/Counters with Separate Prescalar, Compare  One 16-bit TImer/Counter with Separate Prescaler, Compare and Capture mode Real Time Counter with Separate Oscillator Four PWM Channels 8-channel, 10-bit ADC Byte-oriented Two-wire Serial Interface Programmable Serial USART Special Mircocontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages 32 Programmable I/O Lines 40-pin PDIP, 44-lead TQFP, and 44-pad MLF Operating Voltages V for ATmega16 Speed Grades 0-16 MHz for ATmega16 Power Consumption at 4 Mhz, 3V, 35 °C Active: 1.1mA Idle Mode: 0.35mA Power-down Mode:

1 On-board MPU - integrated 6 axis motion processing chip 2 On-board LDO chip, support 5 V / 3.3 V voltage input 3 Commonly used pin have eduction, pin for the standard 2.54 mm 4 Module support IIC standard communication protocol, with 16 bit AD converter, 16 bits of data output 5 Users can control program of the accelerator full grid sensor

3.6 inch TFT LCD Screen For Arduino MEGA Board   Description: Parameters: Dimension:3.6 inch Controller:R Resolution:   data bits: 8 -16 Interface pin number:37 pin Distance:1 mm     3.6 inch LCD   screen   interface definition   (37pin): Sequence Definition 1 NC 2 VDD 3 VDD 4 CS 5 RS 6 WR 7 RD 8 RESET 9 DB0 10 DB1 11 DB2 12 DB3 13 DB4 14 DB5 15 DB6 16 DB7 17 DB8 18 DB9 19 DB DB DB DB DB DB GND 26 NC 27 NC 28 NC 29 NC 30 LED-K6 31 LED-K5 32 LED-K4 33 LED-K3 34 LED-K2 35 LED-K1 36 LED-A 37 GND Powered by Turbo Lister

Specifications: On-board MPU - integrated 6 axis motion processing chip. On-board LDO chip, support 5V / 3.3V voltage input. Commonly used pin have eduction, pin have standard 2.54 mm spacing. Module support IIC standard communication protocol for easy interfacing. 16 bit AD converter that can generate 16 bits of data output. Users can control the accelerator sensor range within 2g, 4g, 8g and 16g. Angular velocity, Sensing range: and / SEC (DPS) SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you  

Package includes: 1 x Atmega8l-8PU + Free 28 Pin base(socket) Features   • High-performance, Low-power AVR ® 8-bit Microcontroller • Advanced RISC Architecture – 130 Powerful Instructions – Most Single-clock Cycle Execution – 32 x 8 General Purpose Working Registers – Fully Static Operation – Up to 16 MIPS Throughput at 16 MHz – On-chip 2-cycle Multiplier • Nonvolatile Program and Data Memories – 8K Bytes of In-System Self-Programmable Flash Endurance: Write/Erase Cycles – Optional Boot Code Section with Independent Lock Bits   In-System Programming by On-chip Boot Program True Read-While-Write Operation – 512 Bytes EEPROM   Endurance: Write/Erase Cycles     1K Byte Internal SRAM   Programming Lock for Software Security   Peripheral Features – Two 8-bit Timer/Counters with Separate Prescaler, one Compare Mode – One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture   Mode – Real Time Counter with Separate Oscillator – Three PWM Channels – 8-channel ADC

6DOF MPU- Module 3 Axis Gyroscope+Accelerometer Module for Arduino MPU DOF MPU- Module 3 Axis Gyroscope+Accelerometer Module for Arduino MPU The MPU- is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU- does away with the cross-axis alignment problems that can creep up on discrete parts. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel. Therefor it captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with the Arduino. The MPU- is not expensive, especially given the fact that it combines both an accelerometer and a gyro. Specifications Chip: MPU- Power supply: 3V-5V power(internal low dropout regulator) Gyroscope range: + ° / s Acceleration range: ± g Communication Mode: standard IIC communication protocol Chip built-in 16 bit AD converter, 16 bits data output Pin pitch 2.54 mm Size: 20.3mm x 15.6mm For more information on its use with arduino you can visit arduino website  Click Here Click Here  to view our other products Contact Us Shipping Payments Feedback We ship our products through reputed shipping services like Fedex, Bluedart, Aramex, DTDC etc. as per availability of the service at customers place. We accept payments only through Paisa Pay. Paisa Pay:The Easiest Way to pay for most of the items is on . We only ship the goods on the address registered with Paisa Pay. If you have any query, please feel free to contact us through "Ask a Question" link under seller information. OR Email Us at: OR Call at: +91- Your feedback is important for us to grow our business on , so please do leave a feedback. If after purchase you have any issues with the product kindly contact us and let us know, leaving a negative feedback will not solve the problem. Like Us on  Facebook 

Atmega328P - PU - 28Pins 20MHz 32kb 8-bit Microcontroller FREE 28 PIN DIP SOCKET  Features High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture 131 Powerful Instructions - Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Up to 6 MIPS Throughput at 16MHz Fully Static Operation On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 32k Bytes of In-System Self-Programmable Flash Optional Boot Code Section with Independent Lock Bits 1K Bytes EEPROM Programming Lock for Software Security Peripheral Features On-chip Analog Comparator Programmable Watchdog Timer with Seperate On-chip Oscillator Master/Slave SPI Serial Interface Two 8-bit Timer/Counters with Separate Prescalar, Compare  One 16-bit TImer/Counter with Seperate Prescaler, Compare and Capture mode Real TIme Counter with Seperate Oscillator Six PWM Channels 8-channel, 10-bit ADC Byte-oriented Two-wire Serial Interface Programmable Serial USART Special Mircocontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages 23 Programmable I/O Lines 28-pin PDIP, 32-lead TQFP, and 28-pad MLF Operating Voltages V for ATmega328P Speed Grades 0-20 MHz for ATmega328P Power Consumption at 1 Mhz, 1.8V, 25 °C Active: 0.2mA Power-down Mode: 0.1µA

Atmega8L - 28Pins 8MHz 8kb 8-bit Microcontroller FREE 28 PIN DIP SOCKET  Features 28-pin AVR Microcontroller Flash Program Memory: 8 kbytes EEPROM Data Memory: 512 bytes SRAM Data Memory: 1 kbytes I/O Pins: 23 Timers: Two 8-bit / One 16-bit A/D Converter: 10-bit Six Channel PWM: Three Channels RTC: Yes with Separate Oscillator MSSP: SPI and I²C Master and Slave Support USART: Yes External Oscillator: up to 8MHz Specifications High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture 130 Powerful Instructions - Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Up to 16 MIPS Throughput at 16MHz Fully Static Operation On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 8k Bytes of In-System Self-Programmable Flash Optional Boot Code Section with Independent Lock Bits 512K Bytes EEPROM Programming Lock for Software Security 1K Byte Internal SRAM Peripheral Features On-chip Analog Comparator Programmable Watchdog Timer with Separate On-chip Oscillator Master/Slave SPI Serial Interface Two 8-bit Timer/Counters with Separate Prescalar, Compare  One 16-bit TImer/Counter with Separate Prescaler, Compare and Capture mode Real TIme Counter with Separate Oscillator Four PWM Channels 8-channel, 10-bit ADC Byte-oriented Two-wire Serial Interface Programmable Serial USART Special Mircocontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages 23 Programmable I/O Lines 28-pin PDIP, 32-lead TQFP, and 32-pad MLF Operating Voltages V for ATmega8L Speed Grades 0-16 MHz for ATmega8 Power Consumption @ 4 MHz, 3V, and 35°C for ATmega8L Active: 3.6mA Idle Mode: 10mA Power-down Mode: 0.5µA

Product Specification LCD size 7.0 inch(Diagonal) Interface Parallel RGB 8 bits Resolution  x 3(RGB) x 600 Driver element a-Si TFT active matrix Dot pitch 0.05(W) ×0.15(H) mm Connections to Banana Pi 40 Pin FPC to the Display Sensor Interface (DSI) Surface treatment Glare Color arrangement RGB-stripe View direction 6 O’Clock Power 5V/550mA Active area  (W) × 90.0H) mm

Graphics Processing Unit NVIDIA GeForce GTX 760 Brand MSI MPN NGD5-OC InterfacePCI Express x Boost / Base Core Clock (Boost Clock: ) Memory Size (MB) Memory Type GDDR5 Memory Interface 256 bits Memory Clock Speed (MHz) DVI Connectors2 (Dual-link DVI-I x 1, Dual-link DVI-D x 1) Max Resolution: x Hz HDMI Connectors1 (version 1.4a) Max Resolution: x Hz DisplayPort1 (version 1.2) Max Resolution: x Hz Maximum Displays 4 HDCP Support Y RAMDAC speed (MHz)400 DirectX Version Support 12 API OpenGL Version Support 4.3 Multi-GPU Technology SLI, 3-way Card Dimension(mm) 242x111x38 mm Card Weight (g) 580 Power consumption (W)170 Recommended PSU (W)500 Power Connectors 2x6-Pin Accessories 2x Molex to 6 pin, User Manual,DVI to VGA Adapter Condition Rarely Used. Well maintained. Dust free. Age 1.5 years Warranty 3 years.Purchased in Jan- yr warranty remainining Reason For Selling: Upgrading to new GPU