Board set pin p4

Set of 4 Pcs AVR40 Base Board  Kit.  For Electronic project.  Atmel AVR - 40 Pin Base Boar d (For ATmega16, AT mega 32,Microcontroller) 1 Pcs 6 Digital Sensors Board for Line Follower    1 Pc 16X2 LCD Board for Display 1 Pc L298N Dual H-Bridge Motor Driver Board. **FREE**4 Pcs FRC Cable. ** Does not Include Any Microcontroller ** Atmel AVR - 40 Pin Base Board AVR-40Pin Development Board -For 40 pin AVR like ATMEGA16, ATMEGA32 etc it Comes without   micocontroller 1 Pc L298N Dual H-Bridge Motor Driver Board. 6 Digital IR - Photodiode Sensors Array for LFR Robot 6 IR-Photodiode Sensors Array- for Line following robot (LFR) and micro-mouse robot  (Digital out, Independent Manual Adjustable) Ideal for LFR (line-follower Robot) obstacles avoiding robots obstacles chasing robot side wall sensor maze solving robots 16x2 LCD Display Board Box Header Connection > LCD Connection (4Bit Mode) Pin#1   > RS(4) Pin#2   > EN(6) Pin#3   > D4(11) Pin#4   > D5(12) Pin#5   > D6(13) Pin#6   > D7(14) Pin#7   > No Connection Pin#8   > No Connection Pin#9   > Gnd () Pin#10 > +5V (2) Note Pin#5 of LCD (RW) is forcefully connected to Ground L298N Dual H-Bridge Motor Driver Board New Improved L298 Dual H-Bridge Board - Ideal for robot motor control, smart  full feature,compact, Compatible with AVR - 40 Board 10 Pin Box Header Connection Description Pin1= ENABLE B Pin2= ENABLE A Pin3= INPUT-3 Pin4= INPUT-1 Pin5= INPUT-4 Pin6= INPUT-2 Pin7= NOT CONNECTED Pin8= NOT CONNECTED Pin9= Ground Pin10=Vcc +5Volt    Fore More Details please refer Datasheet of L298N. ****FREE**** 4 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm. ,with female connectors on both ends. Please Clear Any Doubts "BEFORE" Buying any products form us. Fast Shipping via*      * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post. Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                                                        For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline: Powered by Turbo Lister

    Other Items Feedbacks About Us Contact Us Add To Favorites   Set of 5 Pcs AVR28 Base Board  Kit.  For Electronic project.   CNB009 - Development Board For ATmega8,168,328,5 Pc Kit Electronics DIY Projects Atmel AVR - 28 Pin Base Boar d  -  1 Pcs (For ATmega8 ,ATmega 168,ATmega 328 Microcontroller)  **FREE**    10 Wire FRC Cable -  3 Pcs **FREE**    12V 1Amp SMPS -  1 Pc ** Does not Include Any Microcontroller ** ****FREE**** 3 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm.   ,with female connectors on both ends. Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

LMTF AMP board KIT+Rectifier filter power KIT + Tone control Kit Introduction:   LM is a single channel high-performance Stereo power amplifier IC produced by National Semiconductor Corporation(NS).The maximum continuous output power is up to 60W.From the Introduction till now,it's widely loved by vast audio fans     This power amplifier adopts power board & amplifier board Independent design,for the amplifier part,each channel shares one circuit board,every set includes one power board & 2 single channel power amplifier boards.  All the components on the board are carefully selected,uF/63V capacitors as filter capacitors,35A large current rectifieer bridge,can ensure the powerboard long-term full load working.Other capacitors choose Epcos, Keltron, etc. famous brand capacitors.1% copper pin film resistors. The PCB board adopts single side circuit board, Black boars,reasonable layout design,looks beautiful & generous. In Package  2 X LM mono boards 1 X Hi Fi Tone control board 1 X uf 63v power supply board 1 X 15v regulated power supply board 

LMTF AMP board KIT+Rectifier filter power DIY KIT Introduction:   LM is a single channel high-performance Stereo power amplifier IC produced by National Semiconductor Corporation(NS).The maximum continuous output power is up to 60W.From the Introduction till now,it's widely loved by vast audio fans     This power amplifier adopts power board & amplifier board Independent design,for the amplifier part,each channel shares one circuit board,every set includes one power board & 2 single channel power amplifier boards.  All the components on the board are carefully selected,uF/63V capacitors as filter capacitors,35A large current rectifieer bridge,can ensure the powerboard long-term full load working.Other capacitors choose Epcos, Keltron, etc. famous brand capacitors.1% copper pin film resistors. The PCB board adopts single side circuit board, Black boars,reasonable layout design,looks beautiful & generous.

Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components. 5  Pcs Set of  Mini 2 Pin SPST ON/OFF Switch.  (Colour-BLACK) For Use as ON/OFF switch a circuit board. Fast Shipping via*   * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                 For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline: Powered by Turbo Lister

Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components. 5  Pcs Set of  Mini 2 Pin SPST ON/OFF Switch.  (Colour-BLACK) For Use as ON/OFF switch a circuit board. Fast Shipping via*   * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                 For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline:

Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components. 5  Pcs Set of  Mini 3 Pin SPDT ON/OFF Switch.  (Colour-BLACK) For Use as ON/OFF switch a circuit board. Fast Shipping via*   * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                 For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline:

Arduino mega r3 development board with ATmega + ATmega16U2 with USB cable Arduino mega clone based on current open source hardware atmega atmega16u2 arduino mega best quality 1 set or ARDUINO MEGA R       Product Summary Mega : ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz

Description The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.. The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming in Arduino ). An SD card library is not yet included in the standard Arduino distribution. Arduino communicates with both the W and SD card using the SPI bus (through the ICSP header). This is on digital pins , and 13 on the Duemilanove and pins , and 52 on the Mega. On both boards, pin 10 is used to select the W and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W or the SD card, but it must be kept as an output or the SPI interface won't work. Note that because the W and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W, set digital pin 10 as a high output. The shield provides a standard RJ45 ethernet jack. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

4 Channel IIC I2C Logic Level Converter Bi-Directional Module 5V to 3.3V with  male headers Features: Brand new and high quality. 4 channel board. Color is shown as pictures. Logic Level Converter Bi-Directional Module. Details: If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The CJMCU bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the ‘HV' pin, low voltage (3.3V for example) to ‘LV', and ground from the system to the ‘GND' pin. Note: Due to lighting effects, monitor's brightness/ contrass settings ect, there could be some slight differences

Features: Brand new and high quality. 4 channel board. Color is shown as pictures. Logic Level Converter Bi-Directional Module. Details: If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The CJMCU bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the ‘HV' pin, low voltage (3.3V for example) to ‘LV', and ground from the system to the ‘GND' pin. Note: Due to lighting effects, monitor's brightness/ contrass settings ect, there could be some slight differences

Specifications: GSM SIM900A USB SHIELD GSM/GPRS Module: SIMCOM SIM900A On board Interfaces USB (usb to serial using CP) RS232 with MAX232 TTL pin breakout (RXD,TXD,GND) SIM 900A GSM GPRS Module feature General features •Dual-Band MHz •GPRS multi-slot class 10/8 •GPRS mobile station class B •Compliant to GSM phase 2/2+ – Class 4 (2 W @900 MHz) – Class 1 (1 W @ MHz) •SAIC (Single Antenna Interference Cancellation) support •Dimensions: mm •Weight: 3.4g •Control via AT commands (GSM and SIMCOM enhanced AT Commands) •SIM application toolkit •Supply voltage range : V •Low power consumption: 1.0mA(sleep mode&BS -PA-MFRMS=9) •Operation temperature: -40°C to +85 °C Default Settings on the board The baud rate is set to when we ship the board. You may change it with AT+IPR = . The echo of characters is turned on by default. Downloads SIM 900 AT commands SIM900_AT_Command_Manual_V1.03.pdf USB Driver To connect GSM Modem with computer USB driver is required, please download from Silicon Labs website. GUI for windows Xplore GSM is a Windows GUI and command line software that can be used to test and evaluate the GSM USB Shield.

Photo Resistor 3 Pin  Description Features:  • For Light intensity detected,light brightness sensors, Smart car module  • Using the sensitive type photosensitive resistance sensor  • Waveform of the comparator output signal is good,strong driving ability  • With adjustable potentiometer can adjust and detect the brightness of the light  • Come with bolt holes for easy installation Specifications:  • Using the sensitive type photosensitive resistance sensor  • The comparator output signal clean waveform is good, driving ability, than 15mA.  • With adjustable potentiometer can adjust the brightness of the light detected  • Working voltage 3.3V-5V  • The output form: DO digital switching outputs (0 and 1)  • With bolt holes for easy installation  • A small board PCB size: 3.2cm x 1.4cm  • Using a wide voltage LM393 comparator  Module for Use:  1 The photosensitive resistor module most sensitive to ambient light, generally used to detect the brightness of the ambient light, triggering micro-controller or relay modules;  2 The module brightness of ambient light reach the set threshold, DO-side output high when the ambient light level exceeds the set threshold, DO-ended output low;  3 DO output can be directly connected with the micro-controller through the micro-controller to detect high and low, thereby detecting changes

Description This is a breakout board for Freescale’s MMAL three-axis analog MEMS accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices. Two selectable measuring ranges (±1.5g, ±6g) Breadboard friendly - 0.1" pitch header Low current consumption: 400 µA Sleep mode: 3 µA This breadboard friendly board breaks out every pin of the MMAL to a 9-pin, 0.1" pitch header. The sensor works on power between 2.2 and 3.6VDC (3.3V optimal), and typically consumes just 400µA of current. All three axes have their own analog output. Technical parameters: Voltage Range- DV Static Current- Output Level- High 3.3 V /Low 0V Working Temperature- -  deg   Package Includes: 1 Piece new  MMA  Accellerometer Module 3 Axis  Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description This is a breakout board for Freescale’s MMA7361L three-axis analog MEMS accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices. Two selectable measuring ranges (±1.5g, ±6g) Breadboard friendly - 0.1" pitch header Low current consumption: 400 µA Sleep mode: 3 µA This breadboard friendly board breaks out every pin of the MMA7361L to a 9-pin, 0.1" pitch header. The sensor works on power between 2.2 and 3.6VDC (3.3V optimal), and typically consumes just 400µA of current. All three axes have their own analog output. Technical parameters: Voltage Range- 4.5-20DV Static Current- Output Level- High 3.3 V /Low 0V Working Temperature- -15-+70  deg   Package Includes: 1 Piece new  MMA7361  Accellerometer Module 3 Axis  Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order