Dc motor drive speed

DC Motor / Stepper Driver H Bridge Controller This motor driver is perfect for robotics and mechatronics projects for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms, etc. This is a medium power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L293 motor driver IC. It can drive 4 DC motors on and off, or drive 2 DC motors with directional and speed control. The driver greatly simplifies and increases the ease with which you may control motors, relays, etc from microcontrollers. It can drive motors upto 36V with a total DC current of up to 600mA. You can connect the two channels

DC Motor / Stepper Driver H Bridge Controller This motor driver is perfect for robotics and mechatronics projects and perfect for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms, etc This is a high power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L298 motor driver IC and has onboard 5V regulator which it can supply to an external circuit. It can control upto 4 DC motors, or 2 DC motors with directional and speed control It can drive motors upto 46V with a total DC current of up to 4A. You can connect the two channels

DESCRIPTION Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for Arduino 1. L298N as main chip, ST corporation production. 2. Low heat,outstanding anti-interference performance. 3. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power 25w. 4. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. 5. Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply. 6. Large capacity filter capacitance,afterflow protection diode, more stable and reliable. o Specifications: 2. Double H bridge drive 3. Chip: L298N (ST NEW) 4. Logical voltage: 5V 5. Drive voltage: 5V-35V 6. Logical current: 0mA-36mA 7. Drive current: 2A(MAX single bridge) 8. Size:43 x 43 x 26mm 9. Max power: 25W 10. Net weight: 25g Uses: 11. Driving stepper motor: The connection of driving a common 4 line 2 phase electric motor is shown in figure after enable ENA ENB Input the following driving timing from IN1-IN4-then the speed and direction of the stepper motor can be controlled. 12. Driving DC motor: Because this module is driven by double H bridge,it can drive two motors simultaneously. after enable ENA ENB You can input the speed and direction of PWM signal drive motor 1 from IN1 IN2 You can input the speed and direction of PWM signal drive motor 2 from IN1 IN2 We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC   Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V   Driven part of the peak current Io: 2A   The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)   The logical part of the operating current range: 0 ~ 36mA   Storage temperature: -25 Deg C ~ +130 Deg C   Other Extensions: control of direction indicators, the logic part of the plate to take power interface.Driver Board Size: 55mm * 60mm * 30mm   Drive plate Weight: 33g   Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.

DESCRIPTION L293D Arduino Official Motor Drive ShieldHere is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects. 2 connections for 5V hobby servos connected to the Arduino s high-resolution dedicated timer no jitter! 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 36VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. Pull down resistors keep motors disabled during power-up Big terminal block connectors to easily hook up wires (AWG) and power Arduino reset button brought up top 2-pin terminal block and jumper to connect external power, for seperate logic/motor supplies Tested compatible with Arduino Mega, Diecimila & Duemilanove Download the easy-to-use Arduino software library, check out the examples and you re ready to go! The motor drive, can also drive 4 dc motor can be 600MA through each motor, motor can be run in to the 36V voltage between 4.5 V.Can also drive two stepper motor and two steering gear. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

3A Pulse Width PWM DC Motor Speed Regulator Controller Switch 12V/24V/36V Specifications Control the speed of a DC motor with this controller. Control the light of a lamp with this controller. High efficiency, high torque, high power, high heat dissipation. With overcurrent protection. The high quality COMBICON improve the stability of circuit. Input voltage: DC12V - 36V Sustained current:3A,max.6A(Need to add a cooling fan when max. current) PWM Duty Cycle:% Material: Plastic, metal Size (L*W*H):55mm*35mm*21mm To connect the DC power supply:ensure the power supply voltage 12V - 36V, ensure the power supply output power meet the requirements of the motor work.Dc power don't reverse the positive and negative terminals, otherwise the governor may damage; Line connecting motor: the motor can be both positive and negative, when running direction and expectations are not consistent, can adjust the line sequence by position or to change the direction; Adjust potentiometer knob: adjust potentiometer knob can change speed output duty cycle, motor speed change. Package includes PWM DC Motor Speed Regulator Controller Switch x 1 Images Click here to check out our other products

Description L298N is a kind of high voltage, high current motor driver chip produced by ST company. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V), large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on. Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well. Features： Using L298N made by ST company as the control chip,the module has such characteristics as strong driving  ability, low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage  of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability Specification Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logical current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Size:mm Applied cases: 1) Driving stepper motor The connection of driving a common 4 line 2 phase electric motor is shown

    Other Items Feedbacks About Us Contact Us Add To Favorites   CNB353 - New Original L298N H-Bridge Motor Driver IC for DC,Stepper Motor Drive Make your own DC,Stepper motor Drive/CNC drive Circuit Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

High quality, high torque, high speed DC motor for robotics and machine applications.      Supply 12V DC     Current 1Amp without Load     RPM     Dimensions Length 78MM     Motor Diameter 44.5MM     Weight 370 Grams     Front Shaft Length 12MM     Shaft Diameter 5MM     Mounting Holes 4 Nos, 4 MM     This motor available

High quality, high torque, high speed DC motor for robotics and machine applications.      Supply 12V DC     Current 1 Amp without Load     RPM     Dimension: Length 78MM     Motor Diameter 44.5MM     Weight 370 Grams     Front Shaft Length 12MM     Shaft Diameter 5MM     Mounting Holes 4 Nos, 4 MM     This motor available

PWM 12V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - PWM Duty Cycle: %. - Current: Rated Current: Max 5A with heat sink - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

PWM 12V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - Frequency：25KHz. - PWM Duty Cycle: %. - The maximum current up to 5A radiator or heat required - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

PWM 12V/24V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - Frequency：25KHz. - PWM Duty Cycle: %. - The maximum current up to 5A radiator or heat required - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

Dual H Bridge L298N DC Stepper Motor Drive Controller Specification: Double H bridge drive Chip: L298N (ST NEW) Logical voltage: 5 V Drive voltage: 5 V-35 V Logical current: 0 mA-36 mA Drive current: 2 A (MAX single bridge) Max power: 25 W Size:43 x 43 x 26 mm Net weight: 25 g Package weight:36 g Note: This module has a built-in 5 V power supply, when the driving voltage is 7 V-35 V, this supply is suitable for power supply DO NOT input voltage to +5 V supply interface, however ledding out 5 V for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 Lowest on | Imported | Till stocks last

Description Package Includes: 1 Piece new  Dual H Bridge DC Stepper Motor Drive Controller Board Module Arduino L298N D2