Futaba plug

Futaba Plug to Banana Plug Charge Lead Adapter Use this adapter lead to charge batteries with Futaba Plug plugs. Weight: 14g

The King of all charge leads! If it can not be charged with this, then chances are it doesnt exist! The Plug-King uses quality plugs and high-strand-count silicon wire to ensure a perfect fit and high current charging. If you are worried about shorting, dont be! The Plug-King comes with the T-connector, Traxxas plug and bullet plug covers. You will instantly become everyones friend at your local flying field with this mega charge lead adapter set. The Plug-King is a great addition to any toolkit or workshop. Suits batteries fitted with the following plugs. XT-60 JR (Receiver Pack) Futaba (Receiver Pack) JST T-Connector Micro T-Connector Tamiya (Molex) Mini Tamiya (Mini Molex) HXT-4mm EC3 EC5 Traxxas Losi Mini Plug Futaba (Transmitter Plug) JR (Transmitter Plug) Glow Plug Driver PA45 Micro JST (Eflite, Kyosho, micro helicopter batteries etc.) 2 x Blank Wires (positive and negative for a custom plug)

CC3D EVO CopterControl Hardware Features With a function of being directly plugged into the satellite receiver(It needn't conversion cable) Powerful STM-bit micro controller running at 90MIPs with 128KB Flash and 20KB RAM. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac and Linux. Direct high speed USB support with no drivers required, a truly plug and play device. Spektrum satellite receiver support. Futaba S-BUS hardware support. Innovative Flexi-port technology for superior port flexibility. 4Mbits on-board EEPROM for configuration storage. Flexiport CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs. Superior user experience OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with boot loader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it! Sensors and Components 3-axis Gu Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers. Simultaneous support for multiple receivers. ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development) 10 PWM outputs to servos or ESC’s, or for camera  stabilisation Camera stabilisation: supports up to 3-axis camera mounts with stabilisation and manual control from any of configured receivers. Onboard USB connectivity for easy configuration. USB and serial telemetry and configuration Supported by powerful OpenPilot GCS 4 MB onboard memory 3C Quaternion based complementary filter running at 500Hz Simple Configuration Procedures Connect all ESCs to CC3D Board (Slot

CC3D Board CopterControl from the OpenPilot project introduces a new generation of multi-purpose aircraft stabilization platforms. The CC3D boards is an all-in-one stabilization hardware flight controller, which runs the OpenPilot firmware. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the powerful and user friendly OpenPilot Ground Control Station (GCS) software. The CC3D is an update to the original Copter Control board, now using the powerful single chip IMU. The board shares a lot with the Revolution platform, including the powerful OpenPilot architecture and the cross-platform Ground Control Station (GCS). The CopterControl platform has been designed from the ground up to perform a host of functions from auto-level, multi-copter, Fixed wing UAV’s and even Flybarless Helicopter support. The new included Flexiport provides either I2C connectivity or a second serial port. OpenPilot has made their flight controller as easy and trouble-free as possible. The Open Pilot project, whilst still young, it's trying to make Open Source much more user friendly. You won’t need to buy add-on boards or extra chip programmers. Don’t be fooled by the price. CopterControl provides comparable functionality to other high-end autopilots at a small fraction of the cost. Commercial projects will charge what they can get away with, regardless of quality or features. The non-profit OpenPilot project is different. Consider getting involved and helping the progress. The HobbyKing CC3D board is fully authorized by OpenPilot and built with quality import parts, (unlike the cheap copy boards that can suffer from voltage fluctuations). A portion of the sales of each unit is donated back to the OpenPilot project Specifications Size: 36x36mm Weight: 5.7g Mounting: M3 holes @ 30.5mm square Features: • MultiRotor controller with auto-level, including TriCopters, QuadCopters and HexaCopters • Flybarless Helicopter controller with auto-level • Fixed Wing UAV controller • Powerful STM-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM • 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer • Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance. • Software support for Windows, Mac and Linux • Direct high speed USB support with no drivers required, a truly plug and play device. • Spektrum satellite receiver support • Futaba S-BUS hardware support and PPM • Innovative Flexi-port technology for superior port flexibility • 4Mbits on-board EEPROM for configuration storage Returns In case Product is faulty Buyer must notify us within 24 hours of delivery time and can return within 2 days for a Replacement Or Refund. Returns will be accepted only when products are sent

If you're looking for the ultimate steering servo for your 1/5th scale truck or buggy, we have just the thing! The TrackStar TS-700MG is a large size digital servo featuring a metal gear train, coreless motor and a fast 0.18 sec transit time.  Add to that it's excellent performance and tricked out looks, and you have one outstanding steering servo for the price! Specs: Weight:  145g Size:  63mmx32mmx54mm Torque:  kg.cm (4.8V)  -  kg.cm (6.0V) Speed:  0.20sec/60deg (4.8V) - 0.18 sec/60deg (6.0V) Voltage:  v Type:  Digital Standard Gear Train:  Meta l Ball Bearing:  N2 Ball Bearing Lead Length:  265mm Plug:  JR/Futaba   Weight (g)                     145 Torque (kg)                   Speed(Sec/60deg)       0.18 A(mm)                           62 B(mm)                           60 C(mm)                           56 D(mm)                           28.7 E(mm)                           76 F(mm)                           42