Lcd controller

Item specifics Product Description Specification: Note: 1. /"LIGHT/" linked with GND, the backlight to be lit. 2. Need you to compress the screen and PCB tighter, might got loose after the delivery. 3 Use a 3.3V controller, otherwise the display could be quite vague. LCD Module:   Power supply voltage:2.7V-3.3V,5V is OK,but part of the screen becomes black when tested? Data interface level:2.7-5V? Backlight power supply voltage:highest 3.3V? Module size:43.6mm x 43.1mm(width X height)? Installation diameter:2mm? Backlight:White Document for Download:Data 1RST--------- reset? 2CE------------chip selection? 3DC-----------data/commands choice? 4DIN-----------serial data line? 5CLK------------serial Clock Spee 63.3V------------VCC? 7LIGHT--------- backlight control terminal? 8GND-----------power negative Features: 84 X 84 dot matrix LCD,can show 4 lines of characters Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting time. Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace. LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small Low power supply,the working current

Description：   84 X 84 dot matrix LCD,can show 4 lines of characters   Power supply voltage:2.7V-3.3V   Data interface level:2.7-5V   Backlight power supply voltage:highest 3.3V   Module size:43.6mm(width) x 43.1mm(length)   Installation diameter:2mm Pin Definition:   1.RST--------- reset   2.CE---------- chip selection   3.DC---------- data/commands choice   4.DIN--------- serial data line   5.CLK--------- serial Clock Speed   6.3.3V-------- VCC   7.LIGHT------- backlight control terminal   8.GND--------- power negative 3.Features: 1>. 84 X 84 dot matrix LCD,can show 4 lines of characters 2>. Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the arduino,AVR,PIC,STM32,STC MSP430 and so on.Transfer rate up to 4Mbps,can full speed write display data without waiting time. 3>. Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace. 4>. LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small 5>. Low power supply,the working current

Sound Sensor High Sensitivity Sound Detection Module for Arduino Features: 1.84 X 84 dot matrix LCD, can show 4 lines of characters 2.Use serial interface communicate with the master processor, the number of interface signal line reduced greatly, only 8 signal lines including power and GND. 3.Support different types of MCU, such as the arduino, AVR, SPI, MCS51 and so on. 4.Transfer rate up to 4Mbps, can full speed write display data without waiting time. 5.Can use the conductive glue to connect the module with the printed board, without cables. The metal hooks on the module can fix the module on the printed board, which is very easy to install and replace. 4.LCD controller/driver chip has been bound to LCD chip, the volume of LCD is small 5.Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode Connections: 1.RST--------- reset 2.CE---------- chip selection 3.DC---------- data/commands choice 4.DIN--------- serial data line 5.CLK--------- serial Clock Speed 6.3.3V-------- VCC 7.LIGHT------- backlight control terminal 8.GND--------- power negative Specifications: 1.For Nokia 5110 3V-5V 2.Module size: 45.2mm x 43.1mm Package included: 1x LCD Module for Nokia 5110 Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

5V DC 20 x 4 Lines ASCII Character HD LCD Display With YELLOW Backlight   (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL   Product Overview Product Description: o     LCD display module with  YELLOW Backlight o     SIZE: 20x4 (4 Rows and 20 Characters Per Row) o     Can display 4-lines X 20-characters o     Operate with 5V DC o     Wide viewing angle and high contrast o     Built-in industry standard HD equivalent LCD controller o     Commonly Used in: Student Project, Collage,copiers, fax machines, laser printers, industrial test equipment, networking equipment such as routers and storage devices o     LCM type: Characters   ABOUT This is a basic 20 character by 4 line display YELLOW Backlight. Utilizes the extremely common HD parallel interface chipset (datasheet). Interface code is freely available. You will need 7 general I/O pins(If use

5V DC 20 x 4 Lines ASCII Character HD LCD Display With BLUE Backlight (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL   Product Overview Product Description: o     LCD display module with  BLUE Backlight o     SIZE: 20x4 (4 Rows and 20 Characters Per Row) o     Can display 4-lines X 20-characters o     Operate with 5V DC o     Wide viewing angle and high contrast o     Built-in industry standard HD equivalent LCD controller o     Commonly Used in: Student Project, Collage,copiers, fax machines, laser printers, industrial test equipment, networking equipment such as routers and storage devices o     LCM type: Characters   ABOUT This is a basic 20 character by 4 line display BLUE Backlight. Utilizes the extremely common HD parallel interface chipset (datasheet). Interface code is freely available. You will need 7 general I/O pins(If use

5V DC 20 x 4 Lines ASCII Character HD LCD Display With YELLOW Backlight Product Overview Product Description: o     LCD display module with  YELLOW Backlight o     SIZE: 20x4 (4 Rows and 20 Characters Per Row) o     Can display 4-lines X 20-characters o     Operate with 5V DC o     Wide viewing angle and high contrast o     Built-in industry standard HD equivalent LCD controller o     Commonly Used in: Student Project, Collage,copiers, fax machines, laser printers, industrial test equipment, networking equipment such as routers and storage devices o     LCM type: Characters   ABOUT This is a basic 20 character by 4 line display YELLOW Backlight. Utilizes the extremely common HD parallel interface chipset (datasheet). Interface code is freely available. You will need 7 general I/O pins(If use

2.8 inch TFT LCD touch screen Display ILI x 320 with SD card socket   2.8” LCD TFT display with working arduino code   Description:   This 2.8" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and flash reader design. It is a powerful and multifunctional module for your project. The screen include a controller ILI, it's a support 8/16bit data interface, easy to drive by many MCU like arduino families.STM32, AVR and . It is designed with a touch controller

Description segment Graphic LCD with backlight. Inbuilt KS controller. Features Built-in Controller (KSB) +5V Power Supply 1/64 Duty Cycle Built-in Green Backlight Electrical Characteristics Item Symbol Condition Min Type Max Unit Input Voltage VDD/VIO L Level/H Level 0.7VDD/0 VDD/0.3VDD V Supply Current IDD VDD=5V mA Recommended LC Driving Voltage for Normal Temp. Version Module VDD-VO o / V LED Forward Voltage VF V LED Forward Current IF 25 Array High/Low mA EL Power Supply Current IEL Vel=110VAC;400Hz 5.0 mA Absolute Maximum Ratings Item Symbol Min Typ. Max Unit Power Supply VDD-VSS V Input Voltage VI -0.3 VDD V Mechanical Data Item Standard Value Unit Module Dimension 93.0x70.0x12.1 mm Viewing Area 62.0x33.0 mm Dot Size 0.42x0.48 mm Dot Pitch 0.52x0.52 mm Pin Connection Pin Symbol Level Function 1 Vss 0V Ground/N/V 2 Vdd 5.0V Power Supply(0V) 3 Vee 0V ~ -8V Power Supply for LCD Driver 4 RS H/L Register Select 5 R/W H/L Read/Write 6 E H/L Enable 7 DB0 H/L Data Bus Line 8 DB1 H/L Data Bus Line 9 DB2 H/L Data Bus Line 10 DB3 H/L Data Bus Line 11 DB4 H/L Data Bus Line 12 DB5 H/L Data Bus Line 13 DB6 H/L Data Bus Line 14 DB7 H/L Data Bus Line 15 CS1 H Chip Select 16 CS2 H Chip Select 17 /RST L Reset 18 Vout -10V Voltage 19 LED+ +5V Power Supply for LED B/L (5V) 20 LED- 0V Power Supply for LED B/L (0V) Downloads LCD Datasheet Arduino Library Code We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

2. Hardware The Nokia LCD Module uses a Philips PCD LCD driver, which is designed for mobile phones. Nokia LCD Module 84X48 with backlight 2.1. Operation at 3.3V Many devices that can be used with an Arduino, require a power supply of 3.3V. This is also the case with the Nokia . The best way to deal with 3.3V devices is to take an Arduino Pro, which can run on 3.3V.  Thanks to the internal clamp of the PCD we can use a very simple level shifter. Four current limiting resistors of 10kΩ can do the job. When an LCD control line is high, the current through the 10kΩ resistor is just 40uA, so this is harmless. Note that we can't read back from the LCD with this circuit. 2.2. Operation at 5V Because VDD max = 7V, the PCD controller can handle 5V, but the Nokia LCD works best at 3.3V. The four resistors of 10kΩ avoid streaks on the LCD display. Connecting Nokia LCD to Arduino with 3 wires Note that the Arduino SPI pins 11 and 13 are used to allow hardware SPI. 2.3. PCD supply current versus supply voltage PCD supply current versus supply voltage 2.4. Using the control lines The Nokia LCD has 5 control lines; the interface is of the type SPI. Mostly, when no other SPI devices are used, the chip select can be connected to the GND, so 4 control lines stay over. To save Arduino pins, there is an option to use only 3 control lines, while the Nokia reset pin is connected to the Arduino reset. This works only when the serial monitor is used, not with a standalone Arduino. 2.5. Auto reset circuit An option is to generate a reset pulse on power up automatically, with a RC combination, to save one control line to the Arduino. However, I found out that this solution is poorly reproducible; the proper functioning depends for instance on the capacitor across the 3.3V supply. Also the Arduino can't be used with the serial monitor anymore. 2.6. Nokia LCD with different connector wiring Not all Nokia LCDs are the same. Although they look identical, the connector wiring can be completely different. 3. Software 3.1. Improved PCD library Limor Fried from Adafruit has created a library which can be download at  github. I have changed the library a little bit, you can download it  here.  Changes: Solved problems with bad LCD contacts. Added clear() and init(), for compatibility with older library versions. Unzip the library and place it into the Arduino library folder like this: /libraries/Adafruit_PCD. For troubleshooting see  HERE. Also install the  Adafruit_GFX  library

Professional Solar Watt Meter is an excellent addition to your Solar system,  DC circuits   Battery Backup systems Boat/RV system&  RC hobby ! This best system to measure your solar panel output so you are not fooled by technician of solar panel about output  and to check whether you panels or controller are working properly, a must have thing if you have solar panels.  if checking panel  just connect watt meter source side red wire to positive(solar panel) source black wire to negative (solar panel) then watt meter load red wire to positive(battery or charge controller)  load black wire to negative(battery or charge controller), same way  while checking charge controller  " charge controller to watt meter to battery"  This unit is new 'made

3.2'' TFT LCD Touch Shield for Arduino Mega compatible SAME DAY SHIPPING 100% TESTED PRODUCT, SATISFACTION GUARANTEED. Product Description: 3.2” LCD TFT touch screen display for ARDUINO, AVR, PIC with SD card slot. Display size 3.2” diagonal LCD type TFT   transmissive LCD TFT resolution 240x320 pixels Module power 344mW consumption Colors: 262k Backlight type LED Driver IC: SSD Interface type System Parallel interface Weight 52gms dimension Active Area(W x H):xmm Glass Area(W x H):xmm                                                           Features: v   320x240 pixels screen resolution. v   Specially designed adaptor PCB for display and touchscreen which include SD card slot v   Arduino supported, can be driven by Arduino, AVR, PIC, STM32 and most bits MCUs. v   supported by UTFT library which can directly drive lcd with arduino mega card v   Powerful   SSD controller with [320x240] screen resolution.   Package Include: v   A 3.2” LCD TFT touchscreen display attached adaptor PCB with SD slot. v   A plastic container box.   Shipping Details: Our preferred shipping partners are                             For remote locations we will prefer Indian speed post Feedback v     In case you find any problem

3.2'' TFT LCD 240x400 HD Touch Shield compatible with Arduino Mega Software driver Library AVR included. Product Summary: 3.2” LCD TFT touch screen display for ARDUINO, AVR, PIC with SD card slot. 3.2” Diagonal display 240x400 Display size 3.2” diagonal LCD type TFT   transmissive LCD TFT resolution 240x400 pixels Module power 344mW consumption Colors: 262k Backlight type LED Driver IC HXA Interface type System Parallel interface Weight 52gms dimension Active Area(W x H):xmm Glass Area(W x H):xmm               Features: v   240x400 pixels screen resolution. v   Specially designed adaptor PCB for display and touchscreen which include SD card slot v   Arduino supported, can be driven by Arduino, AVR, PIC, STM32 and most bits MCUs. v   supported by UTFT library which can directly drive LCD with arduino mega card v   Powerful   HXA controller with 240x400 screen resolution.     Package Include: v   A 3.2” LCD TFT 240x400 touchscreen display attached adaptor PCB with SD slot. v   A plastic container box. v   A stand-alone software library(ATmega32)-zip file via e-mail.   Shipping Details: Our preferred shipping partners are                              Indian speed post Testimonial s: v     we never dispatch even a single product without testing at our facility, watch what our customers say about us at our feedback profile Feedback v     In case you find any problem

3.2'' TFT LCD Touch Shield for Arduino Mega compatible     Product Description: 3.2” LCD TFT touch screen display for ARDUINO, AVR, PIC with SD card slot. Display size 3.2” diagonal LCD type TFT   transmissive LCD TFT resolution 240x320 pixels Module power 344mW consumption Colors: 262k Backlight type LED Driver IC: SSD Interface type System Parallel interface Weight 52gms dimension Active Area(W x H):xmm Glass Area(W x H):xmm                                                           Features: v   320x240 pixels screen resolution. v   Specially designed adaptor PCB for display and touchscreen which include SD card slot v   Arduino supported, can be driven by Arduino, AVR, PIC, STM32 and most bits MCUs. v   supported by UTFT library which can directly drive lcd with arduino mega card v   Powerful   SSD controller with [320x240] screen resolution.   Package Include: v   A 3.2” LCD TFT touchscreen display attached adaptor PCB with SD slot. v   A plastic container box.   Shipping Details: Our preferred shipping partners are                             For remote locations we will prefer Indian speed post Feedback v     In case you find any problem

Feature ERMSYG-6 is lcd module ks, RoHS, -20°C to +70°C 6:00, Neg Voltage Generator,Parallel and Serial Interface,ST Controller,Popular Size Attribute Gross Weight (kg) Manufacturer EastRising Series Number ERM Part Number(Order Number) ERMSYG-6 Connection Pin Header Display Format 128x64 Dots Sunlight Readable Yes Touch Panel Optional No Outline Dimension 93.0(W)x70.0(H)x12.5(T)mm Visual Area xmm Active Area (W)x(H) Character Size No Diagonal Size 2.9” Dot (Pixel) Size 0.48x0.48mm Dot Pitch 0.52x0.52mm IC Package COB IC or Equivalent ST Interface -bit Parallel, -bit Parallel, 3-Wire Serial SPI Display Type STN-LCD Yellow Green Response Time(Typ) No Contrast Ratio(Typ) No Colors No Viewing Direction 6:00 Viewing Angle Range No Appearance Dark Blue on Yellow Green Brightness(Typ) No Backlight Color Yellow Green Color Backlight Current (Typ) 60mA Power Supply(Typ) 3.3V Supply Current for LCM(Max) 6mA Operating Temperature -℃ Storage Temperature -℃

 This is a popular 16x2 LCD display. It is based on the HD44870 display controller hence it is easy to interface with most microcontrollers.    It works of 5V and has a Green Backlight which can be switched on and off as desired. The contrast of the screen can also be controlled by varying the voltage at the contrast control pin(Pin 3). The LCD display has 16 pin connection and user should solder the 16 slots available on the side panel with burg connector provided. User has to solder the LCD display with wire to connect with any of the micrcontroller or even a arduino board Use the Male  or Femal Burg connectors to solder on the LCD. This will avoid the time for interfacing.

DESCRIPTION 2.4 Inch Tft Touch Screen Lcd Module For Arduino. The Lcd Has Excellent Vivid Color Contrast. Spice Up Your Arduino Project With A Beautiful Large Touchscreen Display Shield With Built In Microsd Card Connection. This Tft Display Is Big (2.4 Diagonal) Bright (4 White-Led Backlight) And Colorful (18-Bit Different Shades)! Pixels With Individual Pixel Control. It Has Way More Resolution Than A Black And White Display. As A Bonus, This Display Has A Resistive Touchscreen Attached To It Already, So You Can Detect Finger Presses Anywhere On The Screen. 2.4 Diagonal Lcd Tft Display Resolution, 18-Bit () Color Spfd Controller With Built In Video Ram Buffer 8 Bit Digital Interface, Plus 4 Control Lines Uses Digital Pins 5-13 And Analog 0-3. That Means You Can Use Digital Pins 2, 3 And Analog 4 And 5. Pin 12 Is Available If Not Using The Microsd Works With Any Arduino '328 Or Mega (Leonardo Not Supported Yet) 5v Compatible! Use With 3.3v Or 5v Logic Onboard 3.3v 300ma Ldo Regulator 4 White Led Backlight. On By Default But You Can Connect The Transistor To A Digital Pin For Backlight Control 4-Wire Resistive Touchscreen We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

2.4 Inch TFT LCD Shield Touch Board Display Module For Arduino UNO Features: 2.4 inch LCD TFT display Bright, 4 white-LED backlight, on by default but you can connect the transistor to a digital pin for backlight control Colorful, 18-bit different shades 4-wire resistive touchscreen 240 x 320 resolution Spfd controller with built

3.6 inch TFT LCD Screen For Arduino MEGA Board   Description: Parameters: Dimension:3.6 inch Controller:R Resolution:   data bits: 8 -16 Interface pin number:37 pin Distance:1 mm     3.6 inch LCD   screen   interface definition   (37pin): Sequence Definition 1 NC 2 VDD 3 VDD 4 CS 5 RS 6 WR 7 RD 8 RESET 9 DB0 10 DB1 11 DB2 12 DB3 13 DB4 14 DB5 15 DB6 16 DB7 17 DB8 18 DB9 19 DB DB DB DB DB DB GND 26 NC 27 NC 28 NC 29 NC 30 LED-K6 31 LED-K5 32 LED-K4 33 LED-K3 34 LED-K2 35 LED-K1 36 LED-A 37 GND Powered by Turbo Lister

Description: SSD touch panel controller 3.3v voltage regulator LED Backlight 320x240 Pixel Color:   Pins for LCD Control LCDs Pins Description RS Data / Command WR Write RD Read CS Chip Select RST Reset D0-D15 Data Pin Extra VCC, GND, LEDA (LED back light) also need to connect Touch Pin Pins Description D_CLK Clock D_CS Chip Select D_DIN Data

Blue 0.96" inch SPI 128 x 64 OLED display module with CS pin SSD   Fully working Software Code included with English Font.     Description:   What is OLED? OLED   (Organic Light-Emitting Diode) is a self light-emitting technology   composed of a thin, multi-layered organic film placed between an anode   and cathode. In contrast to LCD technology, OLED does not require a   backlight. OLED possesses high application potential for virtually all   types of displays and is regarded as the ultimate technology for the   next generation of flat-panel displays.   How Does OLED Emit Light? OLEDs basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electroluminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components.   Features: Interface: IIC/4-Wire SPI Visual Angle: >160° No backlight needed, the display OLED are self-luminous Fully compatible with arduino, AVR, PIC, 51 series, MSP,STM,CSR or any controller with SPI. Wide range of operating temperature: -30°C to 70°C Easy to use software code due to low pin count Specifications: Display Colour: Blue Input Voltage: 3.3V ~ 6V Compatible I/O Level: 3.3V, 5V Dot Matrix:    128 x 64 Module Size:27.0mm x 27.0mm x 4.0mm Applications: Mobile Display Medical instrumentation Gaming and devices Industrial instrumentation Personal navigation devices   Package Include: ·       1 x   0.96” OLED Display Module ·       A plastic container box ·       Software Code (Zip file e-Mail)   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·        In case you find any problem

Description This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources for Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices

HIGH QUALITY LONG LIFE WASHABLE SILICONE Suitable for TV Air Conditioning Remote Controller Material: Silicone Color: Transparent White Size: 7.2 " x 1.9" x 1.8"

Protect your laptop from overheating by getting topmate Gaming laptop cooling pads online. The laptop Chill Mat with LCD Controller is compatible with 10-15.6 Inch Laptops.

BS 5233 MC Description Automatic Water Level Controller automatically on and off the motor by sensing water in the over head tank, It allows in three modes Auto, manual, Direct (By pass). It is suitable for up to 3Hp single phase submersible, jet, Sump Motors. Using normal Sensors for sense water in tank made with stainless steel material which is corrosion free, Automatic water level controller technically designed with Sensor technology. LCD display shows indication water level in over head tank, letter E- empty L - low H - half F - full. Water Level Controller is an electronic gadget for Control Water Overflow, Very low Power Consumption below 5w. visit us on https://www.srisavita.com

IIC/I2C/TWI/SPI Serial Interface Board Module Port For Arduino LCD Display IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, you may not be able to use normal LCD shield after connecting a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display with only 2 wires. Features: Specifications: Supply voltage: 5V Backlight & Contrast can be adjusted by inbuilt potentiometer. Comes with 2 IIC interface, which can be connected by Dupont wires or IIC dedicated cable Compatible for LCD (16x2) Using this I2C interface module, you can realize data display with only 2 wires. Backlight can be switched using onboard jumper. Size: mm(max) Please contact us for any doubt.Please give us positive feed back.Your feed back is very important for us. Happy to help you.We shipped our material within 2 working days after getting confirmation of payment. contact us- Mob:-     (From 10 AM to 9 PM)    Powered by Turbo Lister

IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, you may not be able to use normal LCD shield after connecting a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display with only 2 wires. Features: Specifications: Supply voltage: 5V Backlight & Contrast can be adjusted by inbuilt potentiometer. Comes with 2 IIC interface, which can be connected by Dupont wires or IIC dedicated cable Compatible for LCD (16x2) Using this I2C interface module, you can realize data display with only 2 wires. Backlight can be switched using onboard jumper. Size: mm(max)

IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, you may not be able to use normal LCD shield after connecting a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display with only 2 wires. Features: Specifications: Supply voltage: 5V Backlight & Contrast can be adjusted by inbuilt potentiometer. Comes with 2 IIC interface, which can be connected by Dupont wires or IIC dedicated cable Compatible for LCD (16x2) Using this I2C interface module, you can realize data display with only 2 wires. Backlight can be switched using onboard jumper. Size: mm(max) = MM_contentVersion; } else if (navigator.userAgent && navigator.userAgent.indexOf("MSIE")>=0 && (navigator.appVersion.indexOf("Win") != -1)) { document.write(' /n'); document.write('on error resume next/n'); document.write('MM_FlashCanPlay = (IsObject(CreateObject("ShockwaveFlash.ShockwaveFlash." & MM_contentVersion)))/n /n'); } if (MM_FlashCanPlay) { document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); } else { document.write(' '); document.write(' '); document.write(' The Buyer Appreciation banner is best viewed with Macromedia Flash Player 6 or higher. '); document.write(' Click here to get the latest Macromedia Flash Player. '); document.write(' '); document.write('

IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, you may not be able to use normal LCD shield after connecting a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display with only 2 wires. Features: Specifications: Supply voltage: 5V Backlight & Contrast can be adjusted by inbuilt potentiometer. Comes with 2 IIC interface, which can be connected by Dupont wires or IIC dedicated cable Compatible for LCD (16x2) Using this I2C interface module, you can realize data display with only 2 wires. Backlight can be switched using onboard jumper. Size: mm(max) SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you

Dell PowerEdge T410 - Compact workstation designed to simplify daily operations Robust Performance and Flexibility Advantageous for Startups,Growing businesses and remote sites that require high performance, flexibility Brand: Dell Product Line: PowerEdge Product Type: Workstation Processors: Latest quad-core or six-Core Intel® Xeon ® processors and series Memory: Up to 128GBs2 (8 DIMM slots3)1GB2/2GBs2/4GBs2/8GBs2/16GBs2 DDRMHz, MHz or MHz.Unbuffered w/ECC or Registered w/ECC at MHz HyperTransport: Intel® QuickPath Interconnect (QPI) Chipset: Intel® chipset Maximum Internal Storage: 12TBs (6x 2TB SATA) 12TBs (6x 2TB NL-SAS) Backup Devices: RD (Internal and External) DATA72 (Internal and External) LTO2-L (Internal and External) LTO (Internal and External) LTO3FH (External) LTO HH (Internal and External) LTO FH (External) Network Controller: 1 Dual port Broadcom BCM Tape Automation:TL/TL ML PV124T Backup and Recovery Software: CommVault/Symantec Backup Exec including Backup Exec System Recovery/Vizioncore Form Factor: 1U Processors: Up to 2x Quad or Six Core Intel Xeon 55xx or 56xx Series Processor Cache: Up to 7MB Memory: Fully Expandable up to 64GB PCR, PCR (8 DIMM slots). Up to 16GB PCE, PCE Hard Drives: Up to 6x 3.5" SAS/SATA hard drives Maximum Internal Storage: Up to 6TB I/O Slots: 4 PCIe slots Remote Management: iDRAC 6 Express, or iDRAC 6 Enterprise Power: Non-Redundant, 525W (80+) Optional Redundant, 580W (80+ GOLD) Auto Ranging (100V~240V) UPS (Uninterruptible Power supplies): 500W – W Extended Battery Module (EBM) Network Management Card AvailabilityQuad-pack LED diagnostic / LCD with Hot-swap HDD Video Card:Matrox G200eW w/ 8MB Management:Dell™ OpenManage™,BMC, IPMI 2.0 compliant Optional: iDRAC6 Express, iDRAC6 Enterprise and vFlash Microsoft® System Center Essential (SCE) v2 Chassis: x x (mm) (w/ bezel, w/ tower foot) x 8.58 x (in) Price -. INR Reason for Selling: Upgraded to Higher Version

sapphire 3d printer system fdm machine / 3d printer sapphire 3d printer system it’s magic! presto sapphire 3d printers open up a whole new world of creativity. it’s like having your personal factory right on your desktop! user-friendly, affordable and quick. turning your ideas and concepts into reality. technology: fused deposition modeling, additive layer manufacturing material class: abs, pla system features configuration system configuration: build envelope (xyz): 250mm(x)×200mm(y)×200mm(z)material delivery: one (1) spool- 1kg20 x 4 characters lcd display and controller to build from sd card. material: options: abs, pla layer thickness:0.4mm 0.3mm 0.2mm available colors: white red black yellow and more... motion:motion resolution: mmposition repeatability: ±0.02mm maximum part weight: 2kg software: operating system: windows xp, ethernet, ieeebuild software: prestocad interface: 3d design software, stl file format installation condition: power: vac hz, single phase, 1ampssize: 430mm(w)×410mm(d)×510mm(h)weight: approx.25kg warranty:(terms & conditions apply)main machine: three (3) months from date of delivery. price is subjected to variation please confirm at the time of enquiry.