Microcontroller based

3 Phase microcontroller based voltage stabilizer.output -3 phase 400V;15KVA Capacity.

Micro Based Running Light Controller kit will attract attention by way of running light effect using 8 bulbs.  An ideal project for use during festival lighting, auspicious occasions at home or social gathering events. Microcontroller based design for greater flexibility and ease of control. Supply input 9 to 12 VDC Mains supply input 240 VAC or 120 VAC Triac based switching of loads connected to the circuit Industry standard isolation with the help of Opto enabled Triac Control Fuse protection for AC output Simple and easy to use 3 tactile switch enabled control of the kit PBT type connector for connecting supply (AC/DC) and TRIAC output on the PCB Onboard regulator for regulated supply to the kit Diode protection for reverse polarity connection of DC supply to the PCB Four mounting holes of 3.2 mm each PCB dimensions 86 mm x 173 mm Assambled

Microcontroller ATmega328 Operating Voltage (logic level) 5 V Connectivity USB Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 8 DC Current per I/O Pin 40 mA Flash Memory 32 KB (ATmega328) of which 2 KB used by bootloader SRAM 1 KB (ATmega168) or 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. INTRODUCTION   Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. with your microcontroller. This module can easily be used with Positron Development Boards.  SALIENT FEATURES This module has 4 pins viz. Receiver, Transmitter, Vcc and Ground These four pins can easily be connected to any of the Transmitter, Receiver, Vcc and Ground of a micro controller development board The module uses MAX232 IC and can be easily connected to your laptop using Positron’s DB9 cables

4 Channel Wired remote work on twisted 2 wire communication based on RS485 protocol, Transmitter based on Encoder PT  and decoder PT, Module has On board microcontroller for Latch outputs, two types of outputs 4Channel Latch and Momentary, Transmitter and Receiver comes with onboard Tri state address Jumpers to pair both the link.   Transmitter Supply 5V-12V DC Receiver Supply 5V-12V DC Address Setting TRI state (Open, Closed, Floating) Very Low current On Board Power and Valid Transmission LEDS Please Read data sheets for more information,

9% Discount 31st March coupon code:  COUPONDUN9 1.     About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

The high-performance, low-power Atmel 8-bit AVR RISC-based microcontroller combines 8KB ISP flash memory, 512B EEPROM, 512-Byte SRAM, 6 general purpose I/O lines, 32 general purpose working registers, one 8-bit timer/counter with compare modes, one 8-bit high speed timer/counter, USI, internal and external Interrupts, 4-channel 10-bit A/D converter, programmable watchdog timer with internal oscillator, three software selectable power saving modes, and debugWIRE for on-chip debugging. The device achieves a throughput of 20 MIPS at 20 MHz and operates between volts. By executing powerful instructions

Company Name: Naksh Researcher & Designer Centre Company Type: Hardware & Software Design in Electronics & Electrical Company Service Area: Microcontroller Based Electronics Projects, Readymade Electronics & Electrical Projects, Electronics IEEE Projects, Electronics Project list, , AVR, PIC Microcontroller, GSM, RFID, DTMF, Robotics, Touch Screen Based Projects, Real Time Electronics Projects, Final Year Electronics Projects, Major & Minor Electronics Projects Electronics & Communication Engineering Projects, Electronics & Electrical Engineering Projects, Electronics Hardware & Software Projects Final Year Major & Minor Projects Field 1. RFID Based Projects 2. DTMF Based Projects 3. GSM Based Projects 4. GPS Based Projects 5. Display Based Projects 6. Robotics Based Projects 7. Remote Control Based Projects 8. Wireless Control Projects 9. Zigbee/Bluetooth Projects 10. Automation Projects 11. Security & Surveillance Projects 12. SCADA Based Projects Keywords Microcontroller , AVR, PIC, LCD, Sensors, Relay, LED, Rectifier, Potentiometer, Resistance, capacitor, Memory, RAM, ROM, UART, RS232, SPI, ADC, Temperature, Accelerometer, RS485, CAN, LIN, I2C, Robotics, GSM 900A, SIM300, GPS, DTMF, Antenna, Wireless, RF Module, Bluetooth, DC motor, stepper Motor, Power supply, regulators etc If you have any idea for any project please feel free to contact us. Contact No: (Mobile), (Land Line)

Line interactive UPS Auto restart while AC is recovering Double boost Automatic voltage regulation (AVR) Wide input range Microcontroller based Generator compatible Battery Level Indicator Call: 7012_ 610_254

Walnut GSM/GPRS Modem USB The GSM/GPRS Modem USB uses SIM900A based Quad band MHz GSM / GPRS module. It can be connected to PC or laptop via  USB directly or to a microcontroller UART using TTL levels. The modem consists of all the external circuit required to start experimenting with the SIM900A module like the power regulation, external antenna, SIM Holder, etc. Modem is built with Quad Band GSM/GPRS based SIM900A module from SIMCOM. It works on frequencies MHz. SIM900A can search these bands automatically. The frequency bands can also be set by AT Commands. The baud rate is configurable from through AT command. The GSM/GPRS Modem is having internal TCP/IP stack to enable you to connect with internet via GPRS. Best suited for GSM based Microcontroller Projects (better than SIM300 and other GSM Modems) **** Can be Use for Bulk SMS sending using Compatible software. Features: U ses the extremely popular SIM900A GSM module. Accepts commands through On board USB serial. Also can accept commands from microcontroller UART. Provides serial TTL interface for easy and direct interface to microcontrollers. Works on 9V-18V 1 A SMPS supply. Speaker and Microphone pins onboard for voice Communication. On board SMA connector with GSM antenna. On board Power, Network, Ring and status LED’s for indication. Can do basic functions which can be done via normal phone like calling, send sms, access data through GPRS etc. Plug and play device. Can accept commands through Hyper Terminal. Ft232 R  Based USB communication- Better and Faster than other Cheap USB Drivers. Supports Windows / Vista / Server / XP / SE / MaC OS X / Mac OS 9,Linux 3.x.x / 2.x.x. Small size. NOTE: The modem consumes current of nearly 1A during transmission; please make sure that your power supply can handle such currents. Modems are pretested before shipping. We recommend to use a 12V DC 2 Amps power supply & Use USB Cable to Connect GSM MODEM to PC or Laptop. Please be very gentle with the SIM card tray while inserting or removing the SIM card. Also don't tighten the screws of the antenna too much, just make sure it is connected properly without exerting too much force to tighen the antenna. This Product Includes: ·          GSM/GPRS Modem USB ·          2 dbi Rubber duck antenna ·          USB Cable ·          USB Driver (FT232R) Please Visit for Download AT Commands & USB Drivers: http://www.walnutinnovations.com/gsm-usb-modem.html Rules and Regulations: 1. All Items

Walnut GSM/GPRS Modem USB The GSM/GPRS Modem USB uses SIM900A based Quad band MHz GSM / GPRS module. It can be connected to PC or laptop via  USB directly or to a microcontroller UART using TTL levels. The modem consists of all the external circuit required to start experimenting with the SIM900A module like the power regulation, external antenna, SIM Holder, etc. Modem is built with Quad Band GSM/GPRS based SIM900A module from SIMCOM. It works on frequencies MHz. SIM900A can search these bands automatically. The frequency bands can also be set by AT Commands. The baud rate is configurable from through AT command. The GSM/GPRS Modem is having internal TCP/IP stack to enable you to connect with internet via GPRS. Best suited for GSM based Microcontroller Projects (better than SIM300 and other GSM Modems) **** Can be Use for Bulk SMS sending using Compatible software. Features: U ses the extremely popular SIM900A GSM module. Accepts commands through On board USB serial. Also can accept commands from microcontroller UART. Provides serial TTL interface for easy and direct interface to microcontrollers. Works on 9V-18V 1 A SMPS supply. Speaker and Microphone pins onboard for voice Communication. On board SMA connector with GSM antenna. On board Power, Network, Ring and status LED’s for indication. Can do basic functions which can be done via normal phone like calling, send sms, access data through GPRS etc. Plug and play device. Can accept commands through Hyper Terminal. Ft232 R  Based USB communication- Better and Faster than other Cheap USB Drivers. Supports Windows / Vista / Server / XP / SE / MaC OS X / Mac OS 9,Linux 3.x.x / 2.x.x. Small size. NOTE: The modem consumes current of nearly 1A during transmission; please make sure that your power supply can handle such currents. Modems are pretested before shipping. We recommend to use a 12V DC 2 Amps power supply & Use USB Cable to Connect GSM MODEM to PC or Laptop. Please be very gentle with the SIM card tray while inserting or removing the SIM card. Also don't tighten the screws of the antenna too much, just make sure it is connected properly without exerting too much force to tighen the antenna. This Product Includes: ·          GSM/GPRS Modem USB ·          2 dbi Rubber duck antenna ·          USB Cable ·          USB Driver CD (FT232R) Please Visit for Download AT Commands & USB Drivers: http://www.walnutinnovations.com/gsm-usb-modem.html Rules and Regulations: 1. All Items

PRODUCT DESCRIPTION The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU   It is the first Arduino board based on a 32-bit ARM core microcontroller.  It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.  On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started.  The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.  The Arduino Due can be powered via the USB connector or with an external power supply.  A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. Technical specs AVR Arduino microcontroller Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-16V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Length mm Width 53.3 mm Weight 36 g

         PRODUCT DESCRIPTION The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU   It is the first Arduino board based on a 32-bit ARM core microcontroller.  It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.  On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started.  The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.  The Arduino Due can be powered via the USB connector or with an external power supply.  A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. Technical specs AVR Arduino microcontroller Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-16V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Length 101.52 mm Width 53.3 mm Weight 36 g

Arduino Compatible DUE R3 32 Bit ARM With FREE USB Cable Description: The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input / output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout. The SAM3X has 512KB (2 blocks of 256KB) of flash memory for storing code. The bootloader is preburned

Package Contents   1 x PIC development Board with Free USB cable and CD containing software examples.   External Power supply NOT Included.    Contact Details   Have any Queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"    The PIC development board is a microcontroller board based on the PIC16F877. It has 33 input/output pins and two PWM outputs, 8 (10 bit) analog inputs, a works upto 20 MHz speed. A USB connection is available for programming and UART (communication with the PC), an external power jack is provided for high current motor applications etc. A Reset button is present. A 4 x 4 key matrix is provided for keyscan applications. A 16 x 2 LCD with programmable backlight is provided. A Piezo Buzzer is present. A 4 digit 7 segment common cathode display is populated for display multiplexing example. A onboard potentiometer is provided on one analog channel. A coin cell battery backed DS (RTC) is present on one of the I2C channel. An optional SPI external EEPROM (not provided with the board) can be mounted by the user for SPI memory. A ULN based stepper motor interface is present.   The Board contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. FEATURES AND USAGE The maximum length and width of the Board is approx 7 inch by 5.5 inches. Four PCB studs allow the board to be attached to a surface or act like a support stand. All the ports of the microcontroller are available as edge connectors on the right side of the board on a standard 100 mil spacing. The board can also take most of the 40 Pin DIP PIC18 series microcontrollers. An External programmer may be needed

Description: The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout. The Arduino Due can be powered via the USB connector or with an external power supply. A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

SAM3X8EA 32bit ARM Contex-M3 Due R3 Board Control  Arduino Due R3 AT91SAM3X8E   Description The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. Features: 1. Microcontroller ：AT91SAM3X8E   2. Operating Voltage：3.3V  3. Input Voltage (recommended)：7-12V  4. Input Voltage (limits)：6-16V  5. Digital I/O Pins ：54 (of which 12 provide PWM output)  6. Analog Input Pins：12 7. Analog Outputs Pins：2 (DAC) 8. Total DC Output Current on all I/O lines ：130 mA 9. DC Current for 3.3V Pin：800 mA   10. DC Current for 5V Pin：800 mA  11. Flash Memory：512 KB all available for the user applications  12. SRAM：96 KB (two banks: 64KB and 32KB)   13. Clock Speed：84 MHz            Driver installation and usage procedure: ·                      Install  Arduino IDE ß  (click here) no extra driver needed for this card. ·                      Connect the board to computer, OS will auto detect ARDUINO DUE ·                      If the board is not auto detected, go to hardware device manager and choose update driver than choose advanced option “install from specific location” and point to the directory where your Arduino IDE is installed e.g. ”C:/program files/arduino-1.0.2/drivers” ·                      Launch Arduino IDE, select board as “arduino DUE” ·                      Select the com port OS created for the card(control panel  à  device manager) ·                      Open basics  à  blink sketch and upload. Package: 1 MCU BOARD  + 1 USB cable

The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout. The Arduino Due can be powered via the USB connector or with an external power supply. The power source is selected automatically. External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Leads from a battery can be inserted in the Gnd and Vin pin headers of the POWER connector. The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is 7 to 12 volts.

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328)

The Arduino Uno is a microcontroller board based on the  ATmega328  (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16  MHz  ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Summary Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16  MHz Length 68.6 mm Width 53.4 mm Weight 25 g

Package Contains 1XArduino Uno R3 1X Usb Cable for Arduino The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

Arduino UNO (Q021) The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g

Description: The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Summary Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

PRODUCT DETAILS: Arduino UNO R3 Compatible Board ATmega328P ATmega16U2 with USB cable DESCRIPTION This is a Compatible board for Arduino uno r3, not original This UNO is a 100% compatible derivative of current R3 Arduino UNO The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller;simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Features:- Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description: Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new AVRDUINO (Arduino compatible) Board. In addition to all the features of the previous board, the AVRDUINO now uses an ATmega KFlash Memory) which can be programmed through Arduino software as well as any AVR programming software. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed). Features: ATmega328 microcontroller (Self Programmable) CAN be used as ARDUINO Board as well as AVR's 28 PIN ATMEGA328 DEVELOPMENT BOARD. Buit In Power Supply: Input voltage -  +7-+12V 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs 32k Flash Memory 16Mhz Clock Speed No Need of any Programmer Package Contents: 1) AVRDuino Board (With ATMEGA328 MICROCONTROLLER) 2) INSTRUCTION MANUAL(Will be sended through Email) 3) DRIVER DETAILS(Will be sended through Email) 4) USB CABLE (FOR CONNECTING AVRDUINO WITH PC/LAPTOP) 5) TUTORIAL OF BURNING PROGRAM OF LED TOGGLE THROUGH Arduino software as well as any AVR programming software. (Will be sended through Email) NOTE: AVRDuino have a dual nature, first as AVR Development Board, second as ARDUINO COMPATIBLE BOARD. Because of its Dual Nature AVRDuino Doesn't Support Serial Monitor

Description: Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new AVRDUINO (Arduino compatible) Board. In addition to all the features of the previous board, the AVRDUINO PRO now uses an ATmega328 which can be programmed through Arduino software. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the AVRDUINO PRO show up as a keyboard, mouse, joystick, etc. Features: ATmega328 microcontroller (Self Programmable) Buit In Power Supply: Input voltage -  +7-+12V 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs 32k Flash Memory 16Mhz Clock Speed No Need of any Programmer InBuilt USB to SERIAL Converted (USB to TTL): Can Use As USB TO SERIAL/TTL CONVERTER ISP Programming Support Package Contents: 1) AVRDuino PRO Board (With ATMEGA328 MICROCONTROLLER) 2) INSTRUCTION MANUAL(Will be sended through Email) 3) DRIVER DETAILS(Will be sended through Email) 4) USB CABLE (FOR CONNECTING AVRDUINO WITH PC/LAPTOP) 5) TUTORIAL OF BURNING PROGRAM OF LED TOGGLE THROUGH Arduino software. (Will be sended through Email)

Product Description: The Mega is a microcontroller board based on the   ATmega ……… Summary Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz

www.hitroncomponents.com Package Contents   1 x UNO R3 ARDUINO COMPATIBLE DEVELOPMENT BOARD 1 x FREE USB Cable   "EXTERNAL POWER SUPPLY IS NOT INCLUDED & HAS TO BE PURCHASED SEPARATELY"   Buy Original Arduino UNO R3 from  http://store.arduino.cc/index.php?main_page=product_info&cPath=11&products_id=195 Download Arduino IDE & Drivers:  http://arduino.cc/en/Main/Software For bulk order get special price Contact Details   Have any queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"       The Arduino Uno is a microcontroller board based on the  ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards

The Freeduino is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Before connecting the Freeduino, CP Driver installation would be required.   Got to link below http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx Or google CP driver download. ------------àSelect as per your Operating system and download the driver------------àUnzip the file on desktop ------------àConnect the UNO with USB Cable given to your computer------------àDevice Manager will display Unknown device for the UNO (CP IC). Right click on the same and click on update driver. Give path as desktop. Wait till driver is installed. ------------àYour CP Driver is installed and Uno is ready for use.