Motor auto controller

DC 12V-40V Large Torque PWM Motor Speed Controller Reversible Control Switch Specifications High Power, High efficiency, Large torque The motor speed controller incorporates a high power MOSFET with a heat sink and can easily provide a continuous current of 3A to your DC motor or other DC load With switch function and Reversible Control function Onboard 10A fuse, with reverse power, over voltage, high current protection function Mode:CCM2NJ Input supply voltage:VDC(max) Maximum output power:120W rated current: 3A Maximum continuous output protecting current:5A PWM frequency: 15kHz Duty Cycle adjustable:% Indicator: Power-On LED Size: 70x39x31mm/2.75"x1.53"x1.22"(approx) Color: as the picture show Package includes 1 x PWM DC Reversible Motor Speed Controller Images Click here to check out our other products

DESCRIPTION Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for Arduino 1. L298N as main chip, ST corporation production. 2. Low heat,outstanding anti-interference performance. 3. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power 25w. 4. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. 5. Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply. 6. Large capacity filter capacitance,afterflow protection diode, more stable and reliable. o Specifications: 2. Double H bridge drive 3. Chip: L298N (ST NEW) 4. Logical voltage: 5V 5. Drive voltage: 5V-35V 6. Logical current: 0mA-36mA 7. Drive current: 2A(MAX single bridge) 8. Size:43 x 43 x 26mm 9. Max power: 25W 10. Net weight: 25g Uses: 11. Driving stepper motor: The connection of driving a common 4 line 2 phase electric motor is shown in figure after enable ENA ENB Input the following driving timing from IN1-IN4-then the speed and direction of the stepper motor can be controlled. 12. Driving DC motor: Because this module is driven by double H bridge,it can drive two motors simultaneously. after enable ENA ENB You can input the speed and direction of PWM signal drive motor 1 from IN1 IN2 You can input the speed and direction of PWM signal drive motor 2 from IN1 IN2 We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

PWM 12V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - PWM Duty Cycle: %. - Current: Rated Current: Max 5A with heat sink - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

PWM 12V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - Frequency：25KHz. - PWM Duty Cycle: %. - The maximum current up to 5A radiator or heat required - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

RF Based DC Motor Direction Controller kit provides an easy way to control the direction of your DC Motor connected to the receiver.  This kit uses the famous HT12E and HT12D encoder / decoder chips from Holtek.  With jumper selectable address on the receiver and transmitter we can control upto 255 more motors

PWM 12V/24V DC Motor Speed Controller DESCRIPTION - Power Supply Require 9V to 24 VDC - Frequency：25KHz. - PWM Duty Cycle: %. - The maximum current up to 5A radiator or heat required - Board was tested before shipping to you. - Can be use to control the speed of Motor Or as LED Dimmer - Quantity: 1 pc - Color: As the picture show - 100% Made In India:) Welcome to ask any question Mob-, Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

30A Brushless Motor Speed Controller RC BEC ESC T-rex 450 V2 Helicopter Boat SU Features: BEC Power: Yes Cut Off Voltage: 4V BEC: Yes BEC Power: 1.5A/5V Reset: Throttle Lowest Con. Current: 30A Battery Range: 5-10 Cells Specification: Size: 57mm x 25mm x 8mm Net weight: 27g Package weight: 33g Color: Yellow Original box: NO Packing Content: 1 x 30A Speed Controller ESC

Dual H Bridge L298N DC Stepper Motor Drive Controller Specification: Double H bridge drive Chip: L298N (ST NEW) Logical voltage: 5 V Drive voltage: 5 V-35 V Logical current: 0 mA-36 mA Drive current: 2 A (MAX single bridge) Max power: 25 W Size:43 x 43 x 26 mm Net weight: 25 g Package weight:36 g Note: This module has a built-in 5 V power supply, when the driving voltage is 7 V-35 V, this supply is suitable for power supply DO NOT input voltage to +5 V supply interface, however ledding out 5 V for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 Lowest on | Imported | Till stocks last

Description L298N is a kind of high voltage, high current motor driver chip produced by ST company. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V), large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on. Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well. Features： Using L298N made by ST company as the control chip,the module has such characteristics as strong driving  ability, low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage  of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability Specification Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logical current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Size:mm Applied cases: 1) Driving stepper motor The connection of driving a common 4 line 2 phase electric motor is shown

Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC   Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V   Driven part of the peak current Io: 2A   The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)   The logical part of the operating current range: 0 ~ 36mA   Storage temperature: -25 Deg C ~ +130 Deg C   Other Extensions: control of direction indicators, the logic part of the plate to take power interface.Driver Board Size: 55mm * 60mm * 30mm   Drive plate Weight: 33g   Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.

ALL TIPE OF HOLE SALE WATER LEVEL CONTROLLER SINGAL PHASE THREE PHASE & INVESTORS 300 W 500 W 750 W 1000 W MANUFACTURING & REPEARING

CNC Stepper Motor Driver 3 Axis TB Stepper Motor Driver Controller       TB Axis CNC Stepper Motor Driver 3 Axis TB Stepper Motor Driver Controller Description: This 3 axis stepper motor driver controller board adopts high-powered professional controller chip TB, making microcomputer applies controller function to driver board to form the smallest controller system

PWM DC 6V 12V 24V 28V 3A Motor Speed Control Switch Controller Regulator This DC Motor Speed Controller allows controlling the speed of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from %.  The motor speed controller can easily provide a continuous current of3A to your DC motor or other DC load.  Input supply voltage: 5V-30VDC  The maximum output power: 80W  The maximum continuous output current: 3A  Duty Cycle adjustable: %  Operating instruction:  1. Connect your DC motor (or DC load) to the motor terminals as indicated on the wiring diagram.  2. Connect a voltage of 5V-30V DC to the circuit making sure of the correct polarity of the connection. Note that the voltage applied to the motor will be supply voltage applied to the circuit. It is recommended to add an appropriately rated fuse inline with the positive supply

DC PWM V Motor Speed Control 10A Pulse Width Modulator Controller Switch Features Power requirement:V Rated current:10A(Maximum output current) PWM Frequency:HZ Control Motor Power:12V:120W(max),24V:230W(max) Regulation range:% The Pulse type is 10A,High-current protection,or Short-circuit current protection Dimension:80mm x 30mm x 55mm(about) Quantity:1PC Package includes 1 x PWM DC Motor speed controller Images Click here to check out our other products

12V-60V 24V 36VStepless PWM 15khz Variable Fan Motor Speed Controller Switch DC Specifications Power input reverse polarity protection, reverse the positive and negative inputs are not damaged, detachable potentiometer connected to the host via a freely plug cable Dimensions: 70 x 39 x 31 mm Operating voltage: DC 12V-60V Output current: 10A Max. (full power, long-term working) Control power: W Quiescent Current: 0.02A (standby) PWM duty cycle: 5% -99% PWM frequency: 15khz Input Anti-reverse Protection: Yes Package includes DC Motor Speed Controller x 1 Images Click here to check out our other products