Relay output board 10a

16 Channel Relay Output Board 10A/250V Relay Board Module Features: With four large capacity uF wave fliter capacitor, make sure enough capacity of power, at the meantime,adopts inductance wave,improve the degree of purity J1,J2 as Relay Control signal interface Specification: Contact: 10A/250VAC,10A 28VDC,15A 120VAC,TV-VAC Output:16 Channels DV:28V10A/ AC:250V 10A or 120V 15A Contact form:1a, 1b, 1c Rated load: 10A/240VAC, 12A/120VAC,15A/120VAC 24VDC Contact resistance: Electrical life: Mechanical life: Coil rated voltage:3-48VDC Coil power:0.36W, 0.45W Coil pick-up voltage: Coil drop-out voltage:>=10% Ambient temperature:-25 degrees Celsius to +70 degrees Celsius Coil and contacts:VAC/min Contact and contacts:VAC/min Insulation resistance:>=100M (ohm)

4-channel relay control board module with optocoupler, 4 way relay module for arduino 4-channel relay output modules, relay output contacts 250A 10A. Input IN1, IN2, IN3, IN4, the signal line LOW effective. VCC, GND power input, can relay a separate power supply relay power input of JD-VCC. Uses: support all MCU control. the industrial sector PLC control smart home control Module parameters: Size: 75mm (length) x 55mm (W) x 19.3mm (height); Weight: 58g; PCB Color: Blue; board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed; Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal; optocoupler isolation, good anti-jamming; Low pull, high release. Energisation status indicator light, release status LED is off; VCC for the system power, JD_VCC for the relay power. Default hair 5V relay, plug the jumper cap to; Relay Maximum output: DC 30V/10A, AC 250V/10A Wiring: VCC: positive power supply system GND: System power supply negative IN1 – IN4: relay control ports Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

4-channel   relay   output modules,   relay   output contacts   250A 10A.   Input   IN1,   IN2,   IN3, IN4,   the signal line   LOW   effective.   VCC, GND   power input,   can   relay   a separate   power   supply   relay   power   input of   JD- VCC. Uses: 1,   support   all   MCU control. 2,   the   industrial sector; 3, PLC   control; 4, smart home   control; FEED BACK We request buyers to leave all star feedback if satisfied and if not satisfied they can communicate and contact us so we can take appropriate action.     Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback      Your feedback is important for us to grow our business on , so please do leave feedback

2 channel RS232 Relay & DAQ Board -iRS-2R Welcome to the world of Computer Automation. This RS232 Relay Board - iRS-2R is a perfect companion for all your computer automation projects. It is RS232 based card having 2 on board relays for switching external devices and up to 4 Digital Input/Output and  Analog channels. The Analog channels have 10 bit resolution for connecting many sensors to measure parameters like Temperature, Pressure, Humidity, Magnetic etc. It uses existing Com Port (you can choose the available one), which allows easy communication with the card. Any programming language that supports serial communications (C, C#, C++, VB, VB.NET, Perl, Java etc) can be used to communicate with iRS-2R very easily. Easy to use commands are available to communicate with iRS-2R for Switching On/Off of Relays and playing with Input/Output channels and Analog inputs. The revised ikantrol-R242 V 1.1 software (freely downloadable from our download section at http://iknowvations.in/downloads/) can be used to test & operate iRS-2R card. For more technical information, please download  iRS-2R User Manual   from our download section   http://iknowvations.in/downloads/.  . If you have any technical information, do write to our support team at support@iknowvations.in

 8 channel RS232 Relay & DAQ Board -iRSD-8R Welcome to the world of Computer Automation. This RS232 Relay Board - iRSD-8R is a perfect companion for all your computer automation projects. It is RS232 based card having 8 onboard relays for switching external devices and up to 8 Digital Input/Output and 4 Analog channels. The Analog channels have 10 bit resolution for connecting many sensors to measure parameters like Temperature, Pressure, Humidity, Magnetic etc. It uses existing Com Port (you can choose the available one), which allows easy communication with the card. Any programming language that supports serial communications (C, C#, C++, VB, VB.NET, Perl, Java etc) can be used to communicate with iRSD-8R very easily. Easy to use commands are available to communicate with iRSD-8R for Switching On/Off of Relays and playing with Input/Output channels and Analog inputs. The revised ikantrol-R242 V 1.1 software (freely downloadable from our download section at http://iknowvations.in/downloads/) can be used to test & operate iRSD-8R card. For more technical information, please download  iRSD-8R User Manual   from our download section   http://iknowvations.in/downloads/.  . If you have any technical information, do write to our support team at support@iknowvations.in

4 channel USB Relay Board with 36 Digital/Analog I/Os USB Data Acquisition Board    Welcome to the world of Computer Automation. This USB Relay Board - U96 is a perfect companion for all your computer automation projects. It is USB based card having 4 onboard relays for switching external devices and up to 36 digital & analogue I/Os that will help you to monitor various real world scenarios using switches & different kind of sensors to monitor many parameters like Temperature, Pressure, Light, Touch, PH etc. This card is not only good for controlling Relays but a perfect example for Data Acquisition applications. It appears as a USB CDC (Communications Device Class) device when connected to USB port of a computer. This creates a Virtual Serial (Com) Port, which allows easy communication with the card. Any programming language that supports serial communications (C, C#, C++, VB, VB.NET, Perl, Java etc) can be used to communicate with U96 very easily. Easy to use commands are available to communicate with U96 which handle various tasks like Switching On/Off of Relays, Controlling Digital Inputs & Outputs, Getting analog data etc. The controller provides 4 relay outputs to control various electrical devices. Apart from this, the card has up to 36 digital input & output pins. It has also got 15 Analog input pins. All pins will be individually configured as Digital Input or Digital output or Analog input automatically as per input command. Each Digital pin can support a TTL or Schmitt Trigger Input or a 3.3V output. Each Analog pin will convert analog voltage (Between 0 to 3V) or Higher (through voltage divider) into 12 bit resolution value. The output can be raw data or converted into voltage. The raw data be converted into required form using conversion formulas. Any kind of sensor whether it is providing digital output or analogue output can be interfaced with U96 and monitored with the help of computer. For more information please download U96 User Manual from our download section at http://iknowvations.in/downloads/. If you have any questions, you can contact our support team at support@iknowvations.in

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc....   ***(Work with All Analog/Digital circuits with signal from 3V to 15V) *** Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 3.3v and 5v micro controller  (Check Other Listings  for  1.8V-5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 3V to 16V(1.5V to 16V for 1.8V logic) with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 3.3V and 5V micro controllers/Digital (1.8V Version also available Please Check My other Listings).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers,  such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc.... ***(Work with All Analog/Digital circuits with signal from 1.5V to 15V) ***   Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 1.8V,3.3v and 5v micro controller  (Check Other Listings  for  3.3V,5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 1.5V to 16V with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 1.8V, 3.3V and 5V micro controllers/Digital).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

Relay SPDT 6V 10A - PCB mount Branded High Quality Relays SPDT 6V 10A PCB Relay Description: Relay SPDT 6V 10A - PCB mount JQC-3FC(T73) DC6V(can be used with 5V). Relays can be used to control both AC and DC appliance which comply with the output rating mentioned below. Relays are used

5V 2 Channel Relay with Optocoupler Description This is a 2-Channel Relay interface board, which can control various appliances, and other equipments. It can be controlled directly by Microcontroller.   Rated voltage: DC12   Rated current: 10A   Coil power: 0.36W  Contact switch voltage: 220VAC  Protective characteristics: Sealed   Contact load: Medium-power  Application: Electromagnetism  Contact Form: Conversion type With 4 mounting holes, diameter of each hole is 3.1mm, easy to install  Apply superior SONGLE relay, SPDT(single-pole double-throw), one common port, one NO and one NC  Opto-isolator, excellent anti-interference performance Low level actuation(indicator ON), high level release(indicator OFF) Maximum output of relay: DC 30 Package Info 1Pc X 5V 2 Channel Relay with Optocoupler SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you

Features The is a 5V 8-Channel Relay interface board with optocoupler which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSC, and so on. Can be powered by 5V DC Source (From USB) Or from the same source powered to Arduino or any other micro controller. Equipped with high-current relay 10A@250 VAC / 10A@28 VDC which can control both AC and DC appliances such as Solenoids, Motors, lights, fans etc High quality screw terminals provided for each relays (C, NC, NO) for quick and easy connection Interfaced with optocouplers to isolate relays & protect your microcontroller. Input Signal Pin connected to Burg stick for easy accessibility LED Status indicators to indicate the relay ON/OFF status. Dimension: 13.4 x 5.3 x 1.7cm (5.28 x 2.09 x 0.67in) Mounting holes provided Shipping contents 1 x 5V DC 8 Channel relay board as shown

Package Contents 1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has one (1) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free wheeling diode which will further protect your microcontroller from relay kick back. This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Free wheeling diode to protect your microcontroller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four (4) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has 2 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided