Rf tx rx bit

Description: The TX is an ASK transmitter module.The TX isdesigned specifically for remote-control, wireless mouseand car alarm system operating at MHz.The RX is a miniature receiver module that receives On-offkeyed (OOK)modulation signal and demodulated to digital signal for the next decoder stage.The RX is designed specifically for remote-control and wireless security receiver operating at Mhz. UART TTL o/p - Baud Rate - . Features: Input Power supply - 5 Volts Compatible for Both RF Mhz Interface upto 8 Bit Data. UART TTL o/p - Baud Rate - Package Includes with RF Tx Rx. Indicating LED's. High quality PCB FR4 Grade with FPT Certified.     Package Contains: RF TX RX with 8 Bit Encoder and Decoder. Billing: Xbee Development Board(RDL/GRS//V1.0) VAT Bill is included. Rules and Regulations: All Items

This RF modulecomprises of an RF Transmitterand an RF Receiver. The transmitter/receiver (Tx/Rx) pair operates at a frequency of 434 MHz. An RF transmitter receives serial data and transmits it wirelessly through RF through its antenna connected at pin4. The transmission occurs at the rate of 1Kbps - 10Kbps.The transmitted data is received by an RF receiver operating at the same frequency as that of the transmitter. The RF module is often used alongwith a pair of encoder/decoder. The encoder is used for encoding parallel data for transmission feed while reception is decoded by a decoder. HT12E-HT12D, HT640-HT648, etc. are some commonly used encoder/decoder pair ICs.

The HT 12E Encoder ICs are series of CMOS LSIs for Remote Control system applications. They are capable of Encoding 12 bit of information which consists of N address bits and 12-N data bits. Each address/data input is externally trinary programmable if bonded out. The HT 12D ICs are series of CMOS LSIs for remote control system applications. This ICs are paired with each other. For proper operation a pair of encoder/decoder with the same number of address and data format should be selected. The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an RF transmission medium and gives output to the output pins after processing the data.

ESP serial Wi-Fi UART wireless IOT module 3.3V AP+STA   For RasPi, arduino, AVR, other MCU ESP serial wifi Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.   Product Description esp serial wifi:   ESP is a highly integrated chip designed for the needs of a new connected IoT world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. Note:   This module requires a 3.3V supply for VCC, and 3.3V logic. It is not 5V tolerant. Connecting Rx or Tx on 5V Arduino may destroy this module. You must use a logic level converter, or a 3.3V Arduino. Also the 3.3V supply on the Arduino Uno has inadequate current capability to power this module. You must provide a separate, higher 3.3V supply (about 300mA or better)   Features ESP serial wifi: ·         SDIO 2.0, SPI, UART ·         Integrated RF switch, balun, 24dBm PA, DCXO, and PMU ·         Integrated RISC processor, on-chip memory and external memory interfaces ·         Integrated MAC/baseband processors ·         Quality of Service management ·         I2S interface for high fidelity audio applications ·         On-chip low-dropout linear regulators for all internal supplies ·         Proprietary spurious-free clock generation architecture ·         Integrated WEP, TKIP, AES, and WAPI engines   Specification ESPEX: ·             b/g/n ·             Wi-Fi Direct (P2P), soft-AP ·             Integrated TCP/IP protocol stack ·             Integrated TR switch, balun, LNA, power amplifier and matching network ·             Integrated PLLs, regulators, DCXO and power management units ·             +19.5dBm output power

Product Description This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector. The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target. This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working. This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector. One of the nice features of this board is a jumper on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level). This board ship default to 5V, but you can cut the default trace and add a solder jumper if you need to switch to 3.3V. Powered by Turbo Lister