Vcc

4-channel relay control board module with optocoupler, 4 way relay module for arduino 4-channel relay output modules, relay output contacts 250A 10A. Input IN1, IN2, IN3, IN4, the signal line LOW effective. VCC, GND power input, can relay a separate power supply relay power input of JD-VCC. Uses: support all MCU control. the industrial sector PLC control smart home control Module parameters: Size: 75mm (length) x 55mm (W) x 19.3mm (height); Weight: 58g; PCB Color: Blue; board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed; Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal; optocoupler isolation, good anti-jamming; Low pull, high release. Energisation status indicator light, release status LED is off; VCC for the system power, JD_VCC for the relay power. Default hair 5V relay, plug the jumper cap to; Relay Maximum output: DC 30V/10A, AC 250V/10A Wiring: VCC: positive power supply system GND: System power supply negative IN1 – IN4: relay control ports Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

IR Reciever and transmitter Description 1、Digital 38KHz IR Transmitter Sensor Description:  IR is widely used in remote control. With this IR transmitter, the Arduino project is able to transmit command to any IR remote Receiver if you have the right decoder.  Well, it will be also easy to make your own IR controller using IR Receiver.   38KHz IR Transmitter Sensor pin definitions : (1) Output (2) Vcc (3) GND  Features:  1、Basedon the 38KHz IR Transmitter Sensor  2、Can be used for remote control  3、Power Supply: 5V  4、Interface: Digital  5、Modulate Frequency : 38Khz  6、Pin Definitions: (1) Output (2) Vcc (3) GND  7、Can be compatible with Wrobot Digital 38KHz IR Receiver Sensor  8、Apply to a variety of platforms including Arduino/51/AVR/ARM      2、Digital 38KHz IR Receiver Sensor Description : IR is widely used in remote control. With this IR receiver, the Arduino project is able to receive command from any IR remoter controller if you have the right decoder. Well, it will be also easy to make your own IR controller using IR transmitter.   38KHz IR Receiver Sensor pin definitions : (1) Output (2) Vcc (3) GND  Features :  1、Based on the 38KHz IR Receiver Sensor  2、Can be used for remoter control  3、Power Supply : 5V  4、Interface : Digital  5、Modulate Frequency : 38Khz  6、Pin Definitions : (1) Output (2) Vcc (3) GND  7、Can be compatible with Wrobot Digital 38KHz IR Transmitter Sensor    Connecting Diagram:   ICA Package Info 1Set X 1pc Transmitter & 1 Pc Receiver Feedback Info We Provide Optimum Quality and Fast Shipping which is self explanatory by Review others have given us please have look if you have any question of doubt. Our Prices are the Cheapest on E-bay, If you find any of our item Selling at cheaper price then Message us the details and we would provide you at same price. For providing such services many individuals and department of ours are working very hard  24hr X 7 X 365 days, and we look for token of appreciation for all this by providing us with positive feedback. For Any Technical Assistance and Guidance Please Post on Our Forum www.sonishop.com/forum We would get back to you for same.

Micro SD Storage Board adap Micro SD TF Card Memory Shield Module SPI Fr Arduino Description 1 Support Micro SD Card, Micro SDHC card (high-speed card)  2 The level conversion circuit board that can interface level is 5V or 3.3V  3 Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board  4 Communication interface is a standard SPI interface  5 4 M2 screw positioning holes for easy installation  6 Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin;  7 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply  8 Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal  9 Micro SD card connector: yes since the bomb deck for easy card insertion and removal  10 Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination  11 Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is SPI bus, CS is the chip select signal pin  V voltage regulator circuit: LDO regulator output is 3.3V level converter chip, Micro SD card supply  13 Level conversion circuit: Micro SD card into the direction of the signal is converted to 3.3V, MicroSD card interfaces to control the direction of the MISO signal is also converted into 3.3V, general AVR microcontroller system can read the signal;  14 Micro SD card connector: a self- bomb deck, easy card insertion.  15 Positioning holes: 4 M2 screws positioning hole diameter is 2.2mm, the positioning of the module is easy to install, to achieve inter- module combination; Package Info 1Pc X Micro SD Storage Board  Feedback Info We Provide Optimum Quality and Fast Shipping which is self explanatory by Review others have given us please have look if you have any question of doubt. Our Prices are the Cheapest on E-bay, If you find any of our item Selling at cheaper price then Message us the details and we would provide you at same price. For providing such services many individuals and department of ours are working very hard  24hr X 7 X 365 days, and we look for token of appreciation for all this by providing us with positive feedback. For Any Technical Assistance and Guidance Please Post on Our Forum www.sonishop.com/forum We would get back to you for same.

Micro SD Storage Board Mciro SD TF Card Memory Shield Module SPI For Arduino New Description: Support Micro SD Card, Micro SDHC card (high-speed card) The level conversion circuit board that can interface level is 5V or 3.3V Communication interface is a standard SPI interface Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply; Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal; Micro SD card connector: yes since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, easy to install positioning, to achieve inter-module combination; Specifications: Power supply:4.5V - 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size:45 x 28mm Net weight:6g Package weight:16g   Package Included: 1PCS*Micro SD Storage Board Mciro SD TF Card Memory Shield Module SPI For Arduino New Welcome to ask any question Mob- , Email Your feedback is important for us to grow our business on , so please  leave Positive feedback Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback

Micro SD Storage Board Mciro SD TF Card Memory Shield Module SPI For Arduino     Product information Features:   Support Micro SD Card, Micro SDHC card (high-speed card) The level conversion circuit board that can interface level is 5V or 3.3V Communication interface is a standard SPI interface Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground,  VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply; Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal; Micro SD card connector: yes since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, easy to install positioning, to achieve inter-module combination; Specifications: Power supply:4.5V - 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size:45 x 28mm Net weight:6g Package weight:16g Shipping content: 1x Micor SD TF Card Shield Expansion Board for Arduino/PIC/ATMEL

1 X LMwatts Mono Amplifier Board, EASP186 Specification: Output power: 68W (4 ohms) 68W Cont. Avg. Output Power into 4Ω at VCC = ±28V 38W Cont. Avg. Output Power into 8Ω at VCC =±28V 50W Cont. Avg. Output Power into 8Ω at VCC = ±35V Signal-to-Noise Ratio ≥ 92dB  PCB Size: mm APPLICATIONS:  • Component stereo  • Compact stereo   • Self-powered speakers   • Surround-sound amplifiers  • High-end stereo TVs Package:   1 X LMwatts Mono Amplifier Board

2 X LMwatts Mono Amplifier Board, EASP186 Specification: Output power: 68W (4 ohms) 68W Cont. Avg. Output Power into 4Ω at VCC = ±28V 38W Cont. Avg. Output Power into 8Ω at VCC =±28V 50W Cont. Avg. Output Power into 8Ω at VCC = ±35V Signal-to-Noise Ratio ≥ 92dB  PCB Size: mm APPLICATIONS:  • Component stereo  • Compact stereo   • Self-powered speakers   • Surround-sound amplifiers  • High-end stereo TVs Package:  2  X LMwatts Mono Amplifier Board PLEASE LEAVE YOUR VALUABLE FEEDBACK

1 X LMwatts Mono Amplifier Board, EASP186 Specification: Output power: 68W (4 ohms) 68W Cont. Avg. Output Power into 4Ω at VCC = ±28V 38W Cont. Avg. Output Power into 8Ω at VCC =±28V 50W Cont. Avg. Output Power into 8Ω at VCC = ±35V Signal-to-Noise Ratio ≥ 92dB PCB Size: mm APPLICATIONS: • Component stereo • Compact stereo • Self-powered speakers • Surround-sound amplifiers • High-end stereo TVs Package: 1 X LMwatts Mono Amplifier Board PLEASE LEAVE YOUR VALUABLE FEEDBACK

LM Overture™ Audio Power Amplifier Series High-Performance 68W Audio Power Amplifier w/Mute.  L M FEATURES DESCRIPTION The LM is a high-performance audio power W Cont. Avg. Output Power into 4Ω at VCC = amplifier capable of delivering 68W of continuous ±28V average power to a 4Ω load and 38W into 8Ω with • 38W Cont. Avg. Output Power into 8Ω at VCC = 0.1% THD+N from 20Hz–20kHz. ±28V The performance of the LM, utilizing its Self • 50W Cont. Avg. Output Power into 8Ω at VCC = Peak Instantaneous Temperature (°Ke) (SPiKe) ±35V protection circuitry, puts it

Description The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Brand new and high quality. Low power consumption Power supply for 2 ~ 5.5V DC Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation Support WIN7 system Technical parameters: Power supply voltage VCC: V Output high VOH: 0.8VCC V Output low VOL:0.3VCC V Output Pin Sink Current (@ VCC = 3V, VOL = 0.6V): 8mA Output pin pull-up current (@ VCC = 3V, VOH = 2.4V):4mA Response time (low power mode):220mS Response time (touch mode):60mS Size:24x24x7.2mm Weight:2g   Package Contents: 1 x Digital Touch Sensor capacitive touch switch module for Arduino Feedback: We provide good quality products & maintain high customer service standards.  We strive for 100% positive feedback for our service.  For assistance, please contact us on  Message  or  If you are satisfied with our service we request you to please leave us a positive feedback and 5 Star DSR ratings

Other Items Feedbacks About Us Contact Us Add To Favorites CNB439 - New Original LM High-Performance 68W Audio Power Amplifier with Mute Description The LM is a high-performance audio power amplifier capable of delivering 68W of continuous average power to a 4Ω load and 38W into 8Ω with 0.1% THD+N from 20Hz–20kHz.    FEATURES DESCRIPTION  The LM is a high-performance audio power  68W Cont. Avg. Output Power into 4Ω at VCC = amplifier capable of delivering 68W of  continuous ±28V average power to a 4Ω load and 38W into 8Ω with • 38W Cont. Avg.  Output Power into 8Ω at VCC = 0.1% THD+N from 20Hz–20kHz. ±28V The performance  of the LM, utilizing its Self • 50W Cont. Avg. Output Power into 8Ω at VCC = Peak  Instantaneous Temperature (°Ke) (SPiKe) ±35V protection circuitry, puts it

    Other Items Feedbacks About Us Contact Us Add To Favorites CNB439 - New Original LM3886 High-Performance 68W Audio Power Amplifier with Mute Description The LM3886 is a high-performance audio power amplifier capable of delivering 68W of continuous average power to a 4Ω load and 38W into 8Ω with 0.1% THD+N from 20Hz–20kHz.    FEATURES DESCRIPTION  The LM3886 is a high-performance audio power  68W Cont. Avg. Output Power into 4Ω at VCC = amplifier capable of delivering 68W of  continuous ±28V average power to a 4Ω load and 38W into 8Ω with • 38W Cont. Avg.  Output Power into 8Ω at VCC = 0.1% THD+N from 20Hz–20kHz. ±28V The performance  of the LM3886, utilizing its Self • 50W Cont. Avg. Output Power into 8Ω at VCC = Peak  Instantaneous Temperature (°Ke) (SPiKe) ±35V protection circuitry, puts it

Product Description This is a wifi solution based on IC ESP from Espressif, very price competitive wifi module, and also great function. Bring your project to the internet of things easily! Features: Very competitive price AP, STA, AP+STA modes available. Very simple AT commands, easy to use. internal LWIP interface. Only four pins interface, VCC-3V3, GND, TXD and RXD. Current firmware V091 for all stock, new reserved reset and CH_PD (for updating) pins available, you can refresh the firmware now. All using new ESPex new chip, old chip is not available anymore. Pin description Pin High Status Low Status Note VCC, GND Use standalone power source, or large capacitor, all power of this module from external TXD, RXD The serial port RST - restart CH_PD Flash boot and Update Mode - chip enable, so always connect to high status with VCC GPIO0 - Update mode GPIO2 - - GPIO 15 (when avaialble) NC Flash boot Mode Only for a few version, Wi07-3 GPIO 12 GPIO 13 GPIO 14 GPIO 16 Hardware RST No need any pull-up   AT Commands Format Baud rate at (new line) use option "send new line" or 'carriage return' for each command x is the commands Set Inquiry Test Execute AT+ = AT+ ? AT+ =? AT+ AT+CWMODE= AT+CWMODE? AT+CWMODE=? - Set the network mode Check current mode Return which modes supported - Commands carefully there are must be no any spaces between the " and IP address or port Commands Description Type Set/Execute Inquiry test Parameters and Examples AT general test basic - - - - AT+RST restart the module basic - - - - AT+GMR check firmware version basic - - - - AT+CWMODE wifi mode wifi AT+CWMODE= AT+CWMODE? AT+CWMODE=? 1= Sta, 2= AP, 3=both, Sta is the default mode of router, AP is a normal mode for devices AT+CWJAP join the AP wifi AT+ CWJAP =, AT+ CWJAP? - ssid = ssid, pwd = wifi password AT+CWLAP list the AP wifi AT+CWLAP AT+CWQAP quit the AP wifi AT+CWQAP - AT+CWQAP=? AT+ CWSAP set the parameters of AP wifi AT+ CWSAP=,,, AT+ CWSAP? ssid, pwd, chl = channel, ecn = encryption; eg. Connect to your router: AT+CWJAP="www.shanrittech.com","helloworld"; and check if connected: AT+CWJAP? AT+CWLIF check join devices' IP wifi AT+CWLIF - - AT+ CIPSTATUS get the connection status TCP/IP AT+ CIPSTATUS,,,, = client or server mode AT+CIPSTART set up TCP or UDP connection TCP/IP 1)single connection (+CIPMUX=0) AT+CIPSTART=,,; 2) multiple connection (+CIPMUX=1) AT+CIPSTART=,, - AT+CIPSTART=? id = 0-4, type = TCP/UDP, addr = IP address, port= port; eg. Connect to another TCP server, set multiple connection first: AT+CIPMUX=1; connect: AT+CIPSTART=4,"TCP","X1.X2.X3.X AT+CIPMODE set data transmission mode TCP/IP AT+CIPMODE= AT+CIPSEND? 0 not data mode, 1 data mode; return "Link is builded" AT+CIPSEND send data TCP/IP 1)single connection(+CIPMUX=0) AT+CIPSEND=; 2) multiple connection (+CIPMUX=1) AT+CIPSEND=, AT+CIPSEND=? eg. send data: AT+CIPSEND=4,15 and then enter the data. AT+CIPCLOSE close TCP or UDP connection TCP/IP AT+CIPCLOSE= or AT+CIPCLOSE AT+CIPCLOSE=? AT+CIFSR Get IP address TCP/IP AT+CIFSR AT+ CIFSR=? AT+ CIPMUX set mutiple connection TCP/IP AT+ CIPMUX= AT+ CIPMUX? 0 for single connection 1 for multiple connection AT+ CIPSERVER set as server TCP/IP AT+ CIPSERVER= [,] mode 0 to close server mode, mode 1 to open; port = port; eg. turn on as a TCP server: AT+CIPSERVER=, check the self server IP address: AT+CIFSR=? AT+ CIPSTO Set the server timeout AT+CIPSTO= AT+CIPSTO?

An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a voltage that varies from 0 to VCC depending on the rotation of the pot. Hook the center pin to an ADC on a microcontroller and get a variable input from the user! The outer two pins will always show 10K resistance, the center pin resistance to one of the outer pins will vary from 10K Ohm to about 50 Ohm. The pot is linear meaning the resistance will vary linearly with its position. This is a good choice for general user interfaces. This pot works great

Product Description This is a wifi solution based on IC ESP from Espressif, very price competitive wifi module, and also great function. Bring your project to the internet of things easily! Features: Very competitive price AP, STA, AP+STA modes available. Very simple AT commands, easy to use. internal LWIP interface. Only four pins interface, VCC-3V3, GND, TXD and RXD. Current firmware V091 for all stock, new reserved reset and CH_PD (for updating) pins available, you can refresh the firmware now. All using new ESPex new chip, old chip is not available anymore. Pin description Pin High Status Low Status Note VCC, GND Use standalone power source, or large capacitor, all power of this module from external TXD, RXD The serial port RST - restart CH_PD Flash boot and Update Mode - chip enable, so always connect to high status with VCC GPIO0 - Update mode GPIO2 - - GPIO 15 (when avaialble) NC Flash boot Mode Only for a few version, Wi07-3 GPIO 12 GPIO 13 GPIO 14 GPIO 16 Hardware RST No need any pull-up AT commands §   Baud rate: (from v0.90, v0.80 and older: ) §   The AT part of the command can be written large or small, however, the following command must always be written large §   Make sure that before, after and within the command no spaces (space) occur General AT commands AT command Description Parameter Example AT Test command, are always "OK" back AT AT + RST Reset of the module, the module's boot messages followed by  ready  back AT + RST AT + GMR Querying the Firmware Version AT + GMR WiFi AT commands AT command Description Parameter Example AT + CWMODE =  Setting the WiFi mode  1) Station 1 =  2 = Access Point  3 = Both AT + CWMODE = 1 AT + CWMODE? Query WiFi mode AT + CWMODE? AT + CWMODE =? Query of possible settings for WiFi mode AT + CWMODE =? AT + CIPMUX = Using multiple connections 0 = single compound  1 = Multiple connections AT + CIPMUX = 1 AT + CIPMODE = Setting the data mode 0 = transparent  1 = Data AT + CIPMODE = 1 AT + CIPMODE? Output of the data set mode AT + CIPMODE? WiFi commands (Station / client) AT command Description Parameter Example AT + CWJAP =, Connecting to WiFi network ssid "SSID"  pass "password" AT + CWJAP = "makerday", "M4k3rd4y" AT + CWJAP? Output of the currently connected WiFi network AT + CWJAP? AT + CWLAP Output of available APs  2) AT + CWLAP AT + CWQAP Closes the connection to an access point AT + CWQAP AT + CIFSR Issue its own IP address AT + CIFSR WiFi commands (Access Point) AT command Description Parameter Example AT + CWSAP =, [,,] Set the access point parameters  3) ssid "SSID"  pass "password"  chan "channel"  enc "Encryption"  (0 = Open  1 = WEP  WPA_PSK 2 =  3 = WPA2_PSK  4 = WPA_WPA2_PSK) AT + CWSAP = "makerday", "M4k3rd4y" 5.3 AT + CWSAP? Output the current settings for the AP AT + CWSAP? AT + CWLIF Lists stations connected IPs 4) AT + CWLIF WiFi commands (IP Client) AT command Description Parameter Example AT + CIPSTATUS Output status of the IP connection (s) AT + CIPSTATUS AT + CIPSTART =,, Creating an IP connection with AT + CIPMUX = 0 type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND = Sending data over a single compound  5) len: Data length AT + CIPSEND = AT + CIPCLOSE Close a single TCP or UDP connection AT + CIPCLOSE AT + CIPSTART =,,, Creating an IP connection with AT + CIPMUX = 1 id: 0-4  type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND =, Send data via merhere compounds 6) id: 0-4  len: Data length AT + CIPSEND = AT + CIPCLOSE = Close one of several TCP or UDP connection id: 0-4 AT + CIPCLOSE = 1 WiFi commands (IP server) AT command Description Parameter Example AT + CIPSERVER = 1 [,] Starts the TCP server port: TCP port AT + CIPSERVER = AT + CIPSERVER = 0 Terminates the TCP server AT + CIPSERVER = 0 AT + CIPSTO = Sets timeout for TCP server timeout = s AT + CIPSTO = 180 AT + CIPSTO? Specifies timeout of TCP server AT + CIPSTO? If a TCP server is started, it can handle up to 5 simultaneous connections. Other compounds can be created, but only served when others are closed or terminated by timeout. The module incoming data directly with the prefix  + IPD  issued: + IPD,   OK   + IPD, 0.6: ON   OK The output is divided as follows: + IPD,,, It is  id  the ID of the compound (0-5),  len  the length of the resulting data packet and  data  contains the data received from the client. In the above example as first sends compound 1 the value   and then connect the string 0  ON     Powered by Turbo Lister

4-channel   relay   output modules,   relay   output contacts   250A 10A.   Input   IN1,   IN2,   IN3, IN4,   the signal line   LOW   effective.   VCC, GND   power input,   can   relay   a separate   power   supply   relay   power   input of   JD- VCC. Uses: 1,   support   all   MCU control. 2,   the   industrial sector; 3, PLC   control; 4, smart home   control; FEED BACK We request buyers to leave all star feedback if satisfied and if not satisfied they can communicate and contact us so we can take appropriate action.     Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback      Your feedback is important for us to grow our business on , so please do leave feedback

Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. INTRODUCTION   Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. with your microcontroller. This module can easily be used with Positron Development Boards.  SALIENT FEATURES This module has 4 pins viz. Receiver, Transmitter, Vcc and Ground These four pins can easily be connected to any of the Transmitter, Receiver, Vcc and Ground of a micro controller development board The module uses MAX232 IC and can be easily connected to your laptop using Positron’s DB9 cables

Item Description: * 100% Brand new and high quality. *   Each functional module has buckled port with VCC, GND and Output, which has corresponding port *   on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. *   Buckled brick cables are like cement for bricks, make the connections easier, secure and more *   professional looking. *   just plug & play. *   Operating Voltage: 5VDC. *   Input Voltage (recommended): 7-12VDC. *   Input Voltage (limits): 6-20VDC. *   Buckled Analog Port: Handy, solid connection to 6 Analog inputs with VCC/GND. *   Digital IO port: 13 ports prepared to digital modules or servos. *   Analog IO Port: 2.54 grid male pin header connections. *   Buckled Communication Port: Selectable between I2C and UARt. *   Size: 7cm x 5.6cm   What's

Other Items Feedbacks About Us Contact Us Add To Favorites CNB Pc 24C Kbit Serial I2C Bus EEPROM Memory IC 2-Wire Serial EEPROM Features • Low-Voltage and Standard-Voltage Operation – 2.7 (VCC = 2.7V to 5.5V) – 1.8 (VCC = 1.8V to 5.5V) • Low-Power Devices (ISB = 2 µA at 5.5V) Available • Internally Organized x 8 • 2-Wire Serial Interface • Schmitt Trigger, Filtered Inputs for Noise Suppression • Bidirectional Data Transfer Protocol • 100 kHz (1.8V, 2.5V, 2.7V) and 400 kHz (5V) Clock Rate • Write Protect Pin for Hardware Data Protection • 32-Byte Page Write Mode (Partial Page Writes Allowed) • Self-Timed Write Cycle (10 ms max) • High Reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years • Automotive Grade and Extended Temperature Devices Available • 8-Pin PDIP Packages Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: AM-6:30PM, Monday-Saturday) email: .in Toll free Helpline: FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

Description The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Features： Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply; Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal; Micro SD card connector: yes since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination; Specification: Support Micro SD Card, Micro SDHC card (high-speed card) The level conversion circuit board that can interface level is 5V or 3.3V Power supply: 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface: Standard SPI interface Positioning holes: 4 M2 screw positioning holes Package included: 1 x  Mciro SD/TF Card Memory Shield Module

USB Micro B Connector Board Description Micro USB Interface Board Power Switch Interface provides the best and convenient way to add USB port to your project with hassle free mounting on and standard PCB board. The breakout board provides a Micro-B USB connector's VCC, GND, ID, D- and D+ pins on a 0.1" pitch header. Features Brand new, High quality and Fast Shipping Color: Blue Size: 150mm x 200mm Pins: VCC, GND, ID, D- and D+ Ideal for an un-regulated 5V supply up to 100mA for any project. Assembled and Tested Protected with ESD pouch Package Includes 1 x USB Micro B Female Breakout Board 1 x 5 pin 0.1 pitch mounting header Shipment All India Free Shipping. We use reliable shipping partners such as BlueDart, DHL, Professional Couriers, DTDC, Aramex etc. The product will be shipped on the same day if the payment has been cleared before 2:00 P.M on weekdays. Next day shipping on Weekends. On receipt of the product, kindly acknowledge the same immediately on Feedback We strive to win 5 star feedback from our esteemed customers. If you are un-satified with the product, please talk to us (contact.saidaikar@gmail.com) before leaving negative feedback. Your feedback is very very important for us to grow our business on , so please do leave feedback. Thank you for your buisness

Sensor Shield V4 Digital Analog Module For Arduino Duemilanove / UNO / MEGA 100% brand new and high quality. Quantity:1pc 　 Size: 70mm x 56mm/2.73"x 2.18''(inch) (approx) 　 Buckled Communication Port: Selectable between I2C and UARt. 　 Analog IO Port: 2.54 grid male pin header connections. 　 Digital IO port: 13 ports prepared to digital modules or servos. 　 Buckled Analog Port: Handy, solid connection to 6 Analog inputs with VCC/GND. 　 Input Voltage (limits): 6-20VDC. 　 Input Voltage (recommended): 7-12VDC. 　 Operating Voltage: 5VDC Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks, make the connections easier, secure and more professional looking. ---1 PC package

Weight 4.5g Size L  58.8 mm x W  16.7 mm x H  10.2 mm Capacities 16GB Performance Min. 14MB/s read, 4MB/s write  (*Actual capacity and performance may vary depending on file format and system specification.) Environmental Conditions Operating Temperature: 0°C to 60°C Storage Temperature: - 25°C to 85°C Vcc  Power: DC V System Compatibility Windows / XP / Vista, / 7 / 8, Mac OS: 10.3 and above Warranty 2 years

Ultrasonic module for electronic projects Features Stable performance Measure the distance accurately Precision: Blind (2cm) super close Parameters Working voltage: DC 5V Quiescent current: 2mA Level output: 5V High 0V Low  Sensor angle: Less than 15 degrees Detection distance: 2 cm - 450 cm High: up to 0.3cm Connection mode: VCC, trig (control side), echo (receiving end), GND Lowest on | Expedited shipping | Till stocks last

16 GB HP v112w 16GB Pen Drive   Features   Design Features a swivel design that protects the drive and eliminates losing the cap Simple Plug and play Convenient pocket-sized for easy transportability.  ·         16GB Storage Capacity   ·         Hi-Speed USB 2.0 for a convenient transfer of large files ·         Compact size and attractive color design ·            WEIGHT 11.5g SIZE 5.0mmH x 15.8mmW x 46.6mmL CAPACITY 8GB PERFORMANCE ‧ 2GB,4GB,8GB: Min.14 MB/s read, 4MB/s write ‧ 16GB,32GB: Min.18 MB/s read, 8MB/s write Operating Voltage Operating Temperature: 0°C to 60°C Storage Temperature: -25°C to 8°C Vcc Power: VDC System Windows , Windows XP, Windows Vista, Windows 7, Mac OS: 10.3 and above

Product features: Using HC - 06 from module 1, a core module, which leads to the interface includes VCC, GND, TXD, RXD, reserved LED state output pin, MCU can state whether the bluetooth is connected through the foot, from machine KEY pin is invalid 2, the led indicates a bluetooth connection status, twinkle said there was no bluetooth connectivity, Chang Liang said bluetooth is connected and turned on the port 3, backplane "3.3 V, the input voltage 3.6 ~ 6 V, current when the unpaired about 30 ma, matching after about 10 ma, no more than 7 V input voltage! 4, interface level 3.3 V, can be connected directly to all kinds of single chip microcomputer (51, AVR, PIC, ARM, MSP430, etc.), 5 V single chip can be connected directly, without MAX232 couldn/'t through MAX, clearing the effective distance of 10 meters, more than 10 meters is possible, but not to this distance connection quality After 6, pairing when full duplex serial port to use, do not need to know any bluetooth protocol, but supports only one

Description：   84 X 84 dot matrix LCD,can show 4 lines of characters   Power supply voltage:2.7V-3.3V   Data interface level:2.7-5V   Backlight power supply voltage:highest 3.3V   Module size:43.6mm(width) x 43.1mm(length)   Installation diameter:2mm Pin Definition:   1.RST--------- reset   2.CE---------- chip selection   3.DC---------- data/commands choice   4.DIN--------- serial data line   5.CLK--------- serial Clock Speed   6.3.3V-------- VCC   7.LIGHT------- backlight control terminal   8.GND--------- power negative 3.Features: 1>. 84 X 84 dot matrix LCD,can show 4 lines of characters 2>. Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the arduino,AVR,PIC,STM32,STC MSP430 and so on.Transfer rate up to 4Mbps,can full speed write display data without waiting time. 3>. Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace. 4>. LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small 5>. Low power supply,the working current

1 Channel Isolated 5V Relay Module Coupling For Arduino PIC AVR DSP ARM   the module is compliant with international safety standards, control and load areas isolation trenches; a single relay a genuine; power supply and relay instructions, lit, disconnect is off; input signal, signal, common Terminal and start conducting; can be used as a single chip modules can be used for appliance control; DC or AC signal, control, you can control the 220V AC load; there is a normally open and one normally closed contact; Specification: One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for avoidance of malfunction Power supply indicator lamp Control indicator lamp Channel: 1 channel Relay Voltage: 5V Note  on the high level and low level triggered mode, friends who do not understand, have a look: High level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way; Low level trigger refers to the signal voltage between input terminal and Earth OV trigger, can be understood as signal input terminal and the GND negative electrode short circuit triggered a way  1-channel relay module connection Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc....   ***(Work with All Analog/Digital circuits with signal from 3V to 15V) *** Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 3.3v and 5v micro controller  (Check Other Listings  for  1.8V-5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 3V to 16V(1.5V to 16V for 1.8V logic) with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 3.3V and 5V micro controllers/Digital (1.8V Version also available Please Check My other Listings).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

Product Description 1x FT232RL USB TO TTL 5V 3.3V Download Cable To Serial Adapter Module For Arduino Shipped via powership. Fast ship - Bluedart/Fedex/DHL/Aramex FT232RL USB TO TTL 5V 3.3V Download Cable To Serial Adapter Module For Arduino Features: 100% Brand new and high quality Material: PCB + Electronic Component Support 3.3V, 5V Main Color: Red Chipset: FT232RL USB power has over current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator Pin definition: DTR,RXD,TX,VCC,CTS,GND Pitch:2.54mm Module Size: About 36mm(length)*17.5mm(width) Interface: Mini USB Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged