Vxl

VXL Tires amp Wheels Assembled Glued Electric Rear Whether racing on a track or tearing across a back lot the rear Alias and front ribbed tires are the perfect choice. Both feature a non-directional design for no-hassle no-worry mounting. The 2.8 ribbed front tire incorporates deep grooved ribs that dig into soft loamy surfaces for superior control. Alias 2.8 rear tires integrate a rounded carcass and dual pin design that steps-up to keep the tires firmly planted on extreme off-road terrain. This tire combination is ideal for use on grass loamy dirt sand and any other loose surface. The Alias rear and ribbed front tires feature a super soft rubber compound that supplies exceptional grip on asphalt and other hard packed surfaces. For a versatile stadium truck tire that is at home on the track or

RPM nbsp Rod Ends cover a wide range of currently available Traxxas vehicles including all versions of the following: Slash 2wd Slash 4x4 Summit nbsp nbsp T-Maxx E-Maxx Revo e-Revo Slayer Pro 4x4 Stampede 4x4 Rustler VXL Jato and Bandit VXL. These rod ends are tough! The area around the ball stud is thicker than the stock rod end while still allowing a full range of motion of the pivot ball. Additionally the shank has been redesigned with a pair of flats making the rod end much easier to work with (versus the stock round shank). RPM rod ends are sold

The most recent electric versions of the e-Rustler e-Stampede Bandit and Slash 2wd have several new features that caused interference issues with our original RPM molded gear cover for the Stampede Rustler. We expanded the area of the gear cover over the motor shaft to compensate for the longer motor shaft of the XL-5 VXL motors. We narrowed two areas along the perimeter of the gear cover to allow clearance for the rear bumper wheelie bar mount as well. These changes now allow this gear cover to fit all versions of these awesome vehicles. RPM Gear Covers for the electric versions of the Traxxas Stampede Rustler Bandit and Slash are sold

This is the Chassis for use on the Traxxas 1 16 E-Revo and Slash VXL Vehicles. FEATURES: Nylon construction Grey

These are the optional Aluminum Toe Links for use on the Traxxas 1 16 scale E-Revo VXL 4WD Brushless RTR. FEATURES: Aluminum construction Anodized red

This is the Main Diff with Steel Ring Gear from Traxxas for the Bandit Stampede and Rustler VXL series. YOU WILL RECEIVE: Main diff with steel ring gear Side cover plate Screws Instructions REQUIREMENTS: Installation on the vehicle tlw ir jxs

this is the differential gear set for use on the Traxxas 1 16 E-revo and Slash VXL vehicles. FEATURES: steel construction YOU WILL RECEIVE: two output gears three spider gears two differential output shafts three 1.5x6mm pins two 1.5x8mm pins REQUIREMENTS: installation on the vehicledescription revised by: DB June

This is the Wing 1 16 E-Revo VXL White Decal Sheet from Traxxas. Traxxas has grown to become the number-1 selling name

This is the Waterproof Micro Servo for use on the Traxxas 1 16 E-Revo and Slash VXL Vehicles. FEATURES: Waterproof Blue nylon case YOU WILL RECEIVE: One Waterproof Micro Servo with standard connector REQUIREMENTS: Installation on the vehicle SPECIFICATIONS: length: 29.5mm (1.2) width: 14mm (0.55) height: 29mm (1.1) cnh ir jxs

This is the Wing Mount for use on the Traxxas 1 16 E-Revo VXL 4WD RTR. FEATURES: Nylon construction Black

This is the Parallel Battery Connection Wire Harness for use on the Traxxas 1 16 E-Revo and Slash VXL Vehicles. FEATURES: Traxxas High Power Connectors Combines mAh of connected batteries for longer run time YOU WILL RECEIVE: One Wire Harness (two Traxxas Male connectors and one Traxxas female connector) Instruction manual REQUIREMENTS: Installation between batteries and ESC cnh ir jxs