Ac dc battery

AC/DC - Operation Travel/Portable 5" Rechargeable Office/Kitchen Table/Desk Fan With Emergency & Torch LIGHT Pls Purchase this Product only if your Delivery Area is Serviced by BLUEDART FEDEX AND ARAMEX ONLY About the Product:. - Mini 5" (Inch) Rechargeable Fan - AC/ DC Function - 24 Pcs of High Bright Light LED's - Rechargeable 4 V. 1.5 Ah Battery - 220 V Round Pin Power Cord - Recharges automatically when operates on AC Power - Minimum 8 Hours of operation on DC Power

Capacity - lbs (kg) Wire length- 15mtrs 12v dc winch All accessories included Quantity available 10no.

MASTECH MS AC/DC DIGTAL CLAMP METER TEMP FREQUENCY This clamp meter allows properties of the electrical current test, like measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. Features: Professional AC/DC digital clamp meter. It is designed according to IEC and IEC concerning safety requirements. Use for measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. When measure DCA, the display can automatically reture to zreo. When measure AC voltage, it can measure the voltage's frequency. Continuity test, can test the circuit to be on or off. With a LCD display to show datas. Data can be hold. Display is counts. Safe and professional. Specifications: Display: counts DCV: V+/-V+/-1.0% ACV: V+/-V+/-1.2% DCA: A+/-3.0% ACA: A+/-3.0% Resistance: k/40k/400k/4Mω+/-Mω+/-2.0% CAP: 4n/40n/400n/4uF+/-4.0% Frequency: 40Hz to 100kHz +/-2.0% Temperature: -40°C to 750°C+/-1.0% Duty cycle: 0.1% to 99.9%  Power: 6F22 9V Battery (BATTERY INCLUDED) Item size: cm Item weight: 414g Package size: cm

MASTECH MSG Digital Clamp Meter Current AC DC Voltage Resistance Tem DESCRIPTION-:   MASTECH MSG Digital Clamp Meter Current AC DC Voltage Resistance Temperature Features: counts LCD display Jaw opening up to 55mm Diode check and continuity test Type-K thermocouple contact temperature measuring Test AC/DC voltage, AC current, resistance, frequency and temperature Overrange indication, low battery indication and Polarity indication Specifications: DC voltage: V¡ÀV¡À1.0% AC voltage: V¡À2.0% AC current: A =600A¡À3.0% Resistance: 200ohm¡Àk/2M ohms¡À1.5% Frequency: 2kHz¡ÀkHz¡À1.5% Temperature: 0 to 750 Centigrade¡À to Fahrenheit¡À2.0% Maximum voltage between terminals and earth ground: CAT II V dc or 750V ac rms. (sine) Display: LCD, counts, updates 2-3/sec. Jaw opening capability: 55mm (Max conductor size) Power supply: 9V battery (NEDA or IEC 6F22)   Operating Environment: 0 to 40 Centigrade Storage temperature: -10¡æ to 50 Centigrade Package includes: 1 * MSG Clamp meter 1 * Set test leads 1 * K-type themocouple probe 1 * User manual  

we only accept Paisapay New Page 1 MASTECH DIGITAL AC / DC AMP CLAMP METER MS TEMPERATURE Description: MASTECH MS AC/DC DIGTAL CLAMP METER TEMP FREQUENCY This clamp meter allows properties of the electrical current test, like measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. Features: Professional AC/DC digital clamp meter. It is designed according to IEC and IEC concerning safety requirements. Use for measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. When measure DCA, the display can automatically reture to zreo. When measure AC voltage, it can measure the voltage's frequency. Continuity test, can test the circuit to be on or off. With a LCD display to show datas. Data can be hold. Display is counts. Safe and professional. Specifications: Display: counts DCV: V+/-V+/-1.0% ACV: V+/-V+/-1.2% DCA: A+/-3.0% ACA: A+/-3.0% Resistance: k/40k/400k/4Mω+/-Mω+/-2.0% CAP: 4n/40n/400n/4uF+/-4.0% Frequency: 40Hz to 100kHz +/-2.0% Temperature: -40°C to 750°C+/-1.0% Duty cycle: 0.1% to 99.9% Power: 6F22 9V Battery (Not included) Item size: cm Item weight: 414g Package size: cm   We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

New Page 1 New Page 1 MASTECH DIGITAL AC / DC AMP CLAMP METER MS TEMPERATURE Description: MASTECH MS AC/DC DIGTAL CLAMP METER TEMP FREQUENCY This clamp meter allows properties of the electrical current test, like measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. Features: Professional AC/DC digital clamp meter. It is designed according to IEC and IEC concerning safety requirements. Use for measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. When measure DCA, the display can automatically reture to zreo. When measure AC voltage, it can measure the voltage's frequency. Continuity test, can test the circuit to be on or off. With a LCD display to show datas. Data can be hold. Display is counts. Safe and professional. Specifications: Display: counts DCV: V+/-V+/-1.0% ACV: V+/-V+/-1.2% DCA: A+/-3.0% ACA: A+/-3.0% Resistance: k/40k/400k/4Mω+/-Mω+/-2.0% CAP: 4n/40n/400n/4uF+/-4.0% Frequency: 40Hz to 100kHz +/-2.0% Temperature: -40°C to 750°C+/-1.0% Duty cycle: 0.1% to 99.9% Power: 6F22 9V Battery (Not included) Item size: cm Item weight: 414g Package size: cm   We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

New Page 1 New Page 1 MASTECH MS AC/DC Digtal Clamp Meter Temp Frequency   DESCRIPTION-: MASTECH MS AC/DC Digtal Clamp Meter Temp Frequency This clamp meter allows properties of the electrical current test, like measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. Features: Professional AC/DC digital clamp meter. It is designed according to IEC and IEC concerning safety requirements. Use for measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. When measure DCA, the display can automatically reture to zreo. When measure AC voltage, it can measure the voltage's frequency. Continuity test, can test the circuit to be on or off. With a LCD display to show datas. Data can be hold. Display is counts. Safe and professional. Specifications: Display: counts DCV: V+/-V+/-1.0% ACV: V+/-V+/-1.2% DCA: A+/-3.0% ACA: A+/-3.0% Resistance: k/40k/400k/4Mω+/-Mω+/-2.0% CAP: 4n/40n/400n/4uF+/-4.0% Frequency: 40Hz to 100kHz +/-2.0% Temperature: -40°C to 750°C+/-1.0% Duty cycle: 0.1% to 99.9% Power: 6F22 9V Battery (Not included) Item size: cm Item weight: 414g Package size: cm  

New Page 1 MASTECH MSC Digital Multimeter AC/DC Volt Detector with Diode & Temp DESCRIPTION-:   MASTECH MSC Digital Multimeter AC/DC Volt Detector with Diode & Temperature Mastech MSC is a manually 19-range fully featured digital multimeter. It is capable of all standard functions including AC/DC Voltage and DC Current, Resistance, diode check, continuity test and temperature (°C & °F selectable).  It uses back-lit LCD display with a maximum reading of . It adopts built-in non-contact AC voltage detector that will detect any AC voltage greater than 90V and send out flash warning.                 No matter you are a professional or just a DIY hobbyist, this is a great and easily affordable tool for your daily use.                                                Features:   3 1/2 digital Back-lit LCD display with a maximum reading Non-contact AC voltage detector (> 90 V/AC) Temperature measurement (°C & °F selectable) In conformance with international safety standards IEC CAT III 600V Data Hold All range protection Over range indication & batter indication Polarity indication Tilt back stand Diode test Continuity test Non-contact AC Voltage detection (> 90V/AC, LED flash warning)                    Specification:   DC Voltage 200m/2V/20V/200V±V±0.8% AC Voltage 200V±V±1.2% DC Current 200μA±1.0%, 2mA±mA±mA±A±3.0% Resistance k/20k/200k±0.8%, 2MΩ±1.0%   Temperature -20 °C - 0 °C ± °C - 400 °C ± °C - °C ±2.0%   -4 °F - 32 °F ± °F - 752 °F ± °F - °F ±2.0% Sampling rate   3 times per second   Power   9V battery  

New Page 1 New Page 1 MASTECH MSC Digital Multimeter AC/DC Volt Detector with Diode & Temp Description: MASTECH MSC Digital Multimeter AC/DC Volt Detector with Diode & Temperature Mastech MSC is a manually 19-range fully featured digital multimeter. It is capable of all standard functions including AC/DC Voltage and DC Current, Resistance, diode check, continuity test and temperature (°C & °F selectable).  It uses back-lit LCD display with a maximum reading of . It adopts built-in non-contact AC voltage detector that will detect any AC voltage greater than 90V and send out flash warning.                 No matter you are a professional or just a DIY hobbyist, this is a great and easily affordable tool for your daily use.                                                Features:   3 1/2 digital Back-lit LCD display with a maximum reading Non-contact AC voltage detector (> 90 V/AC) Temperature measurement (°C & °F selectable) In conformance with international safety standards IEC CAT III 600V Data Hold All range protection Over range indication & batter indication Polarity indication Tilt back stand Diode test Continuity test Non-contact AC Voltage detection (> 90V/AC, LED flash warning)                    Specification:   DC Voltage 200m/2V/20V/200V±V±0.8% AC Voltage 200V±V±1.2% DC Current 200μA±1.0%, 2mA±mA±mA±A±3.0% Resistance k/20k/200k±0.8%, 2MΩ±1.0%   Temperature -20 °C - 0 °C ± °C - 400 °C ± °C - °C ±2.0%   -4 °F - 32 °F ± °F - 752 °F ± °F - °F ±2.0% Sampling rate   3 times per second   Power   9V battery

New Page 1 New Page 1 MT87 Digital Multimeter Electronic Tester AC/DC Clamp Meter Features: 40mm (diagonal) LCD Display Max display: , Auto polarity display Small and compact design Data hold function Overload protection on all ranges Battery low indication   Specifications: Measuring range: Max AC Current:400A Max AC Voltage range:450V Max DC Voltage range:600V Resistance Measurement:200K Ohm range Diode Test / Transistor P-N junction test Continuity test with buzzer sound while Power: 2 x AAA Battery (not include) Weight: 121g Size: cm   Package Including: 1* Digital Clamp Multimeter 2 * Test Leads 1 * English Manual       " width="513" height="518"> MT87 Digital Multimeter Electronic Tester AC/DC Clamp Meter New Page 1 Glass Circle Cutter Can Cut a Exact Round Circle! Glass Circle Cutter Tool Glass Circle Cutter Tool This Glass Circle Cutter   Can Cut a Exact Round Circle! Specifications: Product Name Glass Cutter Material Plastic & Metal Suit for Glass Circle Cutting Package 18" x  Glass Cutter

New Page 1 New Page 1 DESCRIPTION   MASTECH MSC Digital Multimeter AC/DC Volt Detector with Diode & Temperature Mastech MSC is a manually 19-range fully featured digital multimeter. It is capable of all standard functions including AC/DC Voltage and DC Current, Resistance, diode check, continuity test and temperature (°C & °F selectable).  It uses back-lit LCD display with a maximum reading of . It adopts built-in non-contact AC voltage detector that will detect any AC voltage greater than 90V and send out flash warning.     No matter you are a professional or just a DIY hobbyist, this is a great and easily affordable tool for your daily use. Features:   3 1/2 digital Back-lit LCD display with a maximum reading Non-contact AC voltage detector (> 90 V/AC) Temperature measurement (°C & °F selectable) In conformance with international safety standards IEC CAT III 600V Data Hold All range protection Over range indication & batter indication Polarity indication Tilt back stand Diode test Continuity test Non-contact AC Voltage detection (> 90V/AC, LED flash warning)               Specification: DC Voltage 200m/2V/20V/200V±V±0.8% AC Voltage 200V±V±1.2% DC Current 200μA±1.0%, 2mA±mA±mA±A±3.0% Resistance k/20k/200k±0.8%, 2MΩ±1.0%   Temperature -20 °C - 0 °C ± °C - 400 °C ± °C - °C ±2.0%   -4 °F - 32 °F ± °F - 752 °F ± °F - °F ±2.0% Sampling rate   3 times per second   Power   9V battery

New Page 1 New Page 1 NEW MASTECH DIGITAL AC / DC AMP CLAMP METER MS TEMPERATURE FREQUENCY Description: MS This clamp meter allows properties of the electrical current test, like measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. Features:   Professional AC/DC digital clamp meter. It is designed according to IEC and IEC concerning safety requirements. Use for measure AC/DC current, AC/DC voltage, resistance, capacitance,temperature, frequency,diode and circuit, etc. When measure DCA, the display can automatically reture to zreo. When measure AC voltage, it can measure the voltage's frequency. Continuity test, can test the circuit to be on or off. With a LCD display to show datas. Data can be hold. Display is counts. Safe and professional. Data hold & Zero adjustment Carrying case for travel Specifications: Display: counts DCV: V+/-V+/-1.0% ACV: V+/-V+/-1.2% DCA: A+/-3.0% ACA: A+/-3.0% Resistance: k/40k/400k/4Mω+/-Mω+/-2.0% CAP: 4n/40n/400n/4uF+/-4.0% Frequency: 40Hz to 100kHz +/-2.0% Temperature: -40°C to 750°C+/-1.0% Duty cycle: 0.1% to 99.9% Power: 6F22 9V Battery   What's

we only accept Paisapay DESCRIPTION   MASTECH MSC Digital Multimeter AC/DC Volt Detector with Diode & Temperature Mastech MSC is a manually 19-range fully featured digital multimeter. It is capable of all standard functions including AC/DC Voltage and DC Current, Resistance, diode check, continuity test and temperature (°C & °F selectable).  It uses back-lit LCD display with a maximum reading of . It adopts built-in non-contact AC voltage detector that will detect any AC voltage greater than 90V and send out flash warning.     No matter you are a professional or just a DIY hobbyist, this is a great and easily affordable tool for your daily use. Features:   3 1/2 digital Back-lit LCD display with a maximum reading Non-contact AC voltage detector (> 90 V/AC) Temperature measurement (°C & °F selectable) In conformance with international safety standards IEC CAT III 600V Data Hold All range protection Over range indication & batter indication Polarity indication Tilt back stand Diode test Continuity test Non-contact AC Voltage detection (> 90V/AC, LED flash warning)               Specification: DC Voltage 200m/2V/20V/200V±V±0.8% AC Voltage 200V±V±1.2% DC Current 200μA±1.0%, 2mA±mA±mA±A±3.0% Resistance k/20k/200k±0.8%, 2MΩ±1.0%   Temperature -20 °C - 0 °C ± °C - 400 °C ± °C - °C ±2.0%   -4 °F - 32 °F ± °F - 752 °F ± °F - °F ±2.0% Sampling rate   3 times per second   Power   9V battery

New Page 1       BRANDED   MASTECH MSC Digital Multimeter AC/DC Volt Detector with Diode & Temperature Mastech MSC is a manually 19-range fully featured digital multimeter. It is capable of all standard functions including AC/DC Voltage and DC Current, Resistance, diode check, continuity test and temperature (°C & °F selectable).  It uses back-lit LCD display with a maximum reading of . It adopts built-in non-contact AC voltage detector that will detect any AC voltage greater than 90V and send out flash warning.                 No matter you are a professional or just a DIY hobbyist, this is a great and easily affordable tool for your daily use.                                                  Features:   3 1/2 digital Back-lit LCD display with a maximum reading Non-contact AC voltage detector (> 90 V/AC) Temperature measurement (°C & °F selectable) In conformance with international safety standards IEC CAT III 600V Data Hold All range protection Over range indication & batter indication Polarity indication Tilt back stand Diode test Continuity test Non-contact AC Voltage detection (> 90V/AC, LED flash warning)                         Specification:       DC Voltage 200m/2V/20V/200V±V±0.8% AC Voltage 200V±V±1.2% DC Current 200μA±1.0%, 2mA±mA±mA±A±3.0% Resistance k/20k/200k±0.8%, 2MΩ±1.0%   Temperature -20 °C - 0 °C ± °C - 400 °C ± °C - °C ±2.0%   -4 °F - 32 °F ± °F - 752 °F ± °F - °F ±2.0% Sampling rate   3 times per second   Power   9V battery  

New Page 1 New Page 1 New Page 1   Digital Clamp Meter Ac/dc Multimeter Electronic Tester Meter DESCRIPTION -   * High accurate and superior reliable digital multi-meter with LCD screen * Digital Multimeter used to measure AC/DC voltage, AC/DC current, resistance, frequency * Specially designed to meet the daily needs of general engineers and service personnel * Auto ranges with overrange protection function * Compact, reliable and economical, ideal for all toolboxes and pockets * Product Specification: * Display: LCD with maximum reading * Measuring Speed: 2.5 times~3 times per second * Polarity: '-' displayed for negative polarity * Over range Indication: Only figure '1' on the display * Operating Temperature: 0C to 50C * Storage Temperature: -20C to 60C* * Power Supply: NEDA FP 9V battery * Low Battery Indication: Displayed   We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

we only accept Paisapay New Page 1 New Page 1   Digital Clamp Meter Ac/dc Multimeter Electronic Tester Meter DESCRIPTION -   * High accurate and superior reliable digital multi-meter with LCD screen * Digital Multimeter used to measure AC/DC voltage, AC/DC current, resistance, frequency * Specially designed to meet the daily needs of general engineers and service personnel * Auto ranges with overrange protection function * Compact, reliable and economical, ideal for all toolboxes and pockets * Product Specification: * Display: LCD with maximum reading * Measuring Speed: 2.5 times~3 times per second * Polarity: '-' displayed for negative polarity * Over range Indication: Only figure '1' on the display * Operating Temperature: 0C to 50C * Storage Temperature: -20C to 60C* * Power Supply: NEDA FP 9V battery * Low Battery Indication: Displayed   We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

New Page 1 New Page 1 BRANDED UT51 Standard Digital Multimeters AC/DC Resistance Meter Volt Ohm                   Description:- BRANDED UT51 Standard Digital Multimeters AC/DC Resistance Meter Volt Ohm SPECIFICATIONS Basic Functions Range Best Accuracy DC Voltage 200mV/2V/20V/200V/V (0.5%+1) AC Voltage 200mV/2V/20V/200V/750V (0.8%+3) DC Current 20mA/200mA/2mA/20mA/200mA/2A/10A (0.8%+1) AC Current 200mA/2mA/20mA/200mA/2A/10A (1%+3) Resistance 200W/2kW/20kW/200kW/2MW/20MW/200MW (0.8%+1) Special Functions     Fused 10A Range          Transistor          Diode          Continuity Buzzer          Sleep Mode          Low Battery Display          Input Impedance for DC Voltage Measurement 10MW          Max. Display         

we only accept Paisapay New Page 1 New Page 1   MT87 Digital Multimeter Electronic Tester AC/DC Clamp Meter DESCRIPTION Features: 40mm (diagonal) LCD Display Max display: , Auto polarity display Small and compact design Data hold function Overload protection on all ranges Battery low indication   Specifications: Measuring range: Max AC Current:400A Max AC Voltage range:450V Max DC Voltage range:600V Resistance Measurement:200K Ohm range Diode Test / Transistor P-N junction test Continuity test with buzzer sound while Power: 2 x AAA Battery (not include) Weight: 121g Size: cm We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

we only accept Paisapay New Page 1 PRODUCT DESCRIPTION-:   Brand New MT87 Digital Multimeter Electronic Tester AC/DC Clamp Meter Size: mm (diagonal) LCD Display Max display: , Auto polarity display Small and compact design Data hold function Overload protection on all ranges Battery low indication   Specifications: Measuring range: Max AC Current:400A Max AC Voltage range:450V Max DC Voltage range:600V Resistance Measurement:200K Ohm range Diode Test / Transistor P-N junction test Continuity test with buzzer sound while Power: 2 x AAA Battery (not include) Weight: 121g Size: cm   Package Including: 1* Digital Clamp Multimeter 2 * Test Leads 1 * English Manual       We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

New Page 1   Brand New MT87 Digital Multimeter Electronic Tester AC/DC Clamp Meter   PRODUCT DESCRIPTION-: 40mm (diagonal) LCD Display Max display: , Auto polarity display Small and compact design Data hold function Overload protection on all ranges Battery low indication   Specifications: Measuring range: Max AC Current:400A Max AC Voltage range:450V Max DC Voltage range:600V Resistance Measurement:200K Ohm range Diode Test / Transistor P-N junction test Continuity test with buzzer sound while Power: 2 x AAA Battery (not include) Weight: 121g Size: cm   Package Including: 1* Digital Clamp Multimeter 2 * Test Leads 1 * English Manual   Powered by Turbo Lister

New Page 1 New Page 1 New Page 1   MT87 Digital Multimeter Electronic Tester AC/DC Clamp Meter DESCRIPTION Features: 40mm (diagonal) LCD Display Max display: , Auto polarity display Small and compact design Data hold function Overload protection on all ranges Battery low indication   Specifications: Measuring range: Max AC Current:400A Max AC Voltage range:450V Max DC Voltage range:600V Resistance Measurement:200K Ohm range Diode Test / Transistor P-N junction test Continuity test with buzzer sound while Power: 2 x AAA Battery (not include) Weight: 121g Size: cm We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

New Page 1 New Page 1 PRODUCT DESCRIPTION-:   Brand New MT87 Digital Multimeter Electronic Tester AC/DC Clamp Meter Size: mm (diagonal) LCD Display Max display: , Auto polarity display Small and compact design Data hold function Overload protection on all ranges Battery low indication   Specifications: Measuring range: Max AC Current:400A Max AC Voltage range:450V Max DC Voltage range:600V Resistance Measurement:200K Ohm range Diode Test / Transistor P-N junction test Continuity test with buzzer sound while Power: 2 x AAA Battery (not include) Weight: 121g Size: cm   Package Including: 1* Digital Clamp Multimeter 2 * Test Leads 1 * English Manual       We only accept Paisapay. The items will be shipped by Reputed Courier after the payment clear. The delivery period is between days. Please be patient for the parcel and don't leave a bad comment for the shipping time. Please make sure the "Ship To" address you enter during checkout is correct as we are not responsible for wrong or undeliverable addresses. We require a verified shipping address for shipment of your items. We can exchange returned items for you if there is a problem with an item. Every item we offer is backed by a 100% satisfaction guarantee. If your item is not correct or you don't like it for any reason, contact us immediately for return instructions and we will make it right for you. Items must be shipped to us

Rambo EP- Automatic AC DC Switching Air Pump (Battery Not Included) Instructions: High Performance. High Output. Quiet Operation Air Output AC/ cc/ min DC/ cc/min Automatic convert from ac to dc whilst electricity is cutted. supreme Contact Details If you have any further questions, please don’t hesitate to contact me using anyone of the following options: Email/gtalk: sms or whatsapp: +91- Personal Number +91- or just click right hand side corner at seller information "ask seller a question" Create Widget or customize colors.   supremeauctiononlinesoftware.widgets.TextWidget Policies & Guarantees Once we receive order from you, we will ship your item within 2-3 days from our warehouse. U tmost we try to send products same day or next workning day, however it depends upon time & day you order, staff and product availability. We won't be able to dispatch your item on National Regional Holidays & on Sundays. We ship product nationwide, yes truely nationwide no matter where you live

High Power 27 LED / SMD with 15 Hours Backup Rechargeable Emergency Light WITH BIG SMD MORE BRIGHTNESS Powerfull Battery and fast rechargeable. AC/DC Function Automatic Light Up Function Can use by 3 X AA 1.5V Battery also. Two mode button Low Light and High Light Ultra Long life rechargeable battery. In-build Portable Stand Super bright Big 27 SMD used are energy saving & high efficiency with ultra long life. SMD brightness can be adjusted between High & Low brightness.