Digital thermal sensor

4Pin Digital Thermal Thermistor Temperature Sensor Module For Arduino Features: 1. Using the NTC thermistor sensor, good sensitivity 2. The comparator output signal clean waveform is good, driving ability, than 15mA. 3. Adjust the temperature distribution bit detection threshold 4. Working voltage 3.3V-5V 5. The output format: Digital switching output (0 and 1) 6. With bolt holes for easy installation 7. A small board PCB size: 3.2cm x 1.4cm 8. Using a wide voltage LM393 comparator Module for use: 1. The thermal resistance of the module is very sensitive to the ambient temperature, generally used to detect the ambient temperature; 2. Through the adjustment of the potentiometer, can change the temperature detection threshold (ie, temperature control value), if necessary to control the ambient temperature is 50 degrees, the module

See our ratings Add this shop to my favorites DS18B20 DS18S20 Waterproof Digital Thermal Sensor Probe ₹ Availability:

Description 100% brand new and high quality Using the NTC thermistor sensor, good sensitivity The comparator output signal clean waveform is good, driving ability, than 15mA Adjust the temperature distribution bit detection threshold Using a wide voltage LM393 comparator With bolt holes for easy installation Module Usage The thermal resistance of the module is very sensitive to the ambient temperature and is generally used to detect the ambient temperature Through the adjustment of the potentiometer one can change the temperature detection threshold (ie, temperature control value), if necessary to control the ambient temperature is 50 degrees, the module

Digital Touch Sensor TTP223B capacitive touch switch module for Arduino Product Description   Specification: The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Features: Low power consumption Power supply for 2 ~ 5.5V DC Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation Package Contents: 1x  Digital Touch Sensor  TTP223B  capacitive touch switch module for Arduino Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Description Package Includes: 1 Piece new  Digital Light Sensor Intensity Seek Module Photoresistor For Arduino It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  by PhraseFinder" style="border: none !important; display: inline-block !important; text-indent: 0px !important; float: none !important; font-weight: bold !important; height: auto !important; margin: 0px !important; min-height: 0px !important; min-width: 0px !important; padding: 0px !important; text-transform: uppercase !important; text-decoration: underline !important; vertical-align: baseline !important; width: auto !important; background: transparent !important;"> Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Photo Resistor 3 Pin  Description Features:  • For Light intensity detected,light brightness sensors, Smart car module  • Using the sensitive type photosensitive resistance sensor  • Waveform of the comparator output signal is good,strong driving ability  • With adjustable potentiometer can adjust and detect the brightness of the light  • Come with bolt holes for easy installation Specifications:  • Using the sensitive type photosensitive resistance sensor  • The comparator output signal clean waveform is good, driving ability, than 15mA.  • With adjustable potentiometer can adjust the brightness of the light detected  • Working voltage 3.3V-5V  • The output form: DO digital switching outputs (0 and 1)  • With bolt holes for easy installation  • A small board PCB size: 3.2cm x 1.4cm  • Using a wide voltage LM393 comparator  Module for Use:  1 The photosensitive resistor module most sensitive to ambient light, generally used to detect the brightness of the ambient light, triggering micro-controller or relay modules;  2 The module brightness of ambient light reach the set threshold, DO-side output high when the ambient light level exceeds the set threshold, DO-ended output low;  3 DO output can be directly connected with the micro-controller through the micro-controller to detect high and low, thereby detecting changes

LOWEST PRICE IN   e b a y 10 TIMES MORE RELIABLE THAN OTHER CHINESE MODULE BEST FOR YOUR ROBOT / INDUSTRIAL  PURPOSE  /HOME & AUTOMATION 1 MONTHS REPLACEMENT WARRENTY IN CASE OF ANY PROBLEM DUE TO MANUFACTURING DIFFECT  HIGH QUALITY FR-4 BOARD Light Sensor For Arduino / PIC / AVR Description Module Features:    1, Using sensitive photosensitive resistance sensor    2,The comparator output signal is clean, good waveform, driving ability, more than 15mA.    3, With adjustable potentiometer to adjust the brightness of the light detection    4,The working voltage 3.3V-5V    5, DUAL OUTPUT form: DO digital switching outputs (0 and 1) and AO analog voltage output     6,A fixed bolt holes for easy installation    7, PCB Size: 3.4cm x 4.0cm   8, Using a wide voltage LM393 comparator Product wiring instructions:   1, VCC positive power supply 3.3-9V   2, GND power supply is negative   3, DO TTL switching signal output     4, AO analog output Please contact us for any doubt.Please give us positive feed back.Your feed back is very important for us. Happy to help you.We shipped our material within 2 working days after getting confirmation of payment. contact us- Mob:-     (From 10 AM to 9 PM)    Powered by Turbo Lister

LM35D Digital temperature sensor linear analog output module DC4-30V Digital temperature sensor LM35D module cables free   Product Description:   ·         100% brand new and high quality ·         Low power consumption, less than 60uA ·         low output impedance, 1mA current through only 0.1 Ohm ·         screw holes for easy installation and fix. Aperture 2.6mm ·         LM35D operates with a wide range of voltage 4-30V ·         linear analog output

Description The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Brand new and high quality. Low power consumption Power supply for 2 ~ 5.5V DC Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation Support WIN7 system Technical parameters: Power supply voltage VCC: V Output high VOH: 0.8VCC V Output low VOL:0.3VCC V Output Pin Sink Current (@ VCC = 3V, VOL = 0.6V): 8mA Output pin pull-up current (@ VCC = 3V, VOH = 2.4V):4mA Response time (low power mode):220mS Response time (touch mode):60mS Size:24x24x7.2mm Weight:2g   Package Contents: 1 x Digital Touch Sensor capacitive touch switch module for Arduino Feedback: We provide good quality products & maintain high customer service standards.  We strive for 100% positive feedback for our service.  For assistance, please contact us on  Message  or  If you are satisfied with our service we request you to please leave us a positive feedback and 5 Star DSR ratings

Description Package Includes: 1 Piece new  TTP Channel Digital Touch Sensor Module / Capacitive Touch Switch button It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91  between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

DESCRIPTION Capacitive Digital Touch Sensor Hand Detection Module For Arduino Features: Touch key detection IC, providing a touch key. Touch detection IC is designed to replace traditional keys with variable area. Button keys and design. Low power consumption and wide operating voltage DC and AC touch key features. Specifications: Input operating voltage: DC 2.0V - 5.5V Input with reverse polarity protection. LED Color: BLUE, connected to Output pin Idle current: Size: 15.5 x 23.5 mm Connection: Vcc, Output, GND Package included: 1 x Hand detection module We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

  Description Package Includes: 1 Piece new  TTP 224 4 Channel Digital Touch Sensor Module / Capacitive Touch Switch button It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91  9793202258 between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description The module is based on a touch-sensing IC  (TTP223B) capacitive touch switch module. In the normal state, the module output  low, low power consumption; When a finger touches the corresponding position,  the module output high, if not touched for 12 seconds, switch to low-power mode. Jog type: the initial state is low, high  touch, do not touch is low (similar touch of a button feature) Module can be installed

Description 100% brand new and high quality Here is a DS18B20 original chip,three wire temperature sensor High quality stainless steel tube encapsulation waterproof moisture proof prevent rust No other components, unique single bus interface 9 ~ 12 adjustable resolution Accuracy over the range of -10°C to +85°C: ±0.5°C. Specification: Power supply range:3.0V-5.5V (Included) Operating temperature range: -55°C - +125°C (-67°F - +257°F) Storage temperature range: -55°C to - +125°C (-67°F - +257°F) Signal Output Type: Analog Output lead:red (VCC), yellow(DATA), black(GND) Cable length:Approx.100 cm Color:As shown /   Feedback: We provide good quality products & maintain high customer service standards.  We strive for 100% positive feedback for our service.  For assistance, please contact us on  Message  or  If you are satisfied with our service we request you to please leave us a positive feedback and 5 Star DSR ratings

LOWEST PRICE IN   e b a y 10 TIMES MORE RELIABLE THAN OTHER CHINESE MODULE BEST FOR YOUR ROBOT / INDUSTRIAL  PURPOSE  /HOME & AUTOMATION 1 MONTHS REPLACEMENT WARRENTY IN CASE OF ANY PROBLEM DUE TO MANUFACTURING DIFFECT 4 Types of sensor Thermal, Magnetic, Flame & Light Sensor Module All modules have Four Pin 2 For Power & 2 For Output Digital & Analog. Also Have Output Led Indicator. Package Content Total 4 items 1 x Flame sensor module 1x Thermal Sensor Module 1x Digital Light Sensor Module 1x Magnetic Field Sensor Module Description: Thermal Sensor Module: 1. Using the NTC thermistor sensor, good sensitivity 2. The comparator output signal clean waveform is good, driving ability, than 15mA. 3. Adjust the temperature distribution bit detection threshold 4. Working voltage 3.3V-5V 5. The output format: Digital switching output (0 and 1) 6. With bolt holes for easy installation 7. A small board PCB size: 3.2cm x 1.4cm 8. Using a wide voltage LM393 comparator Module for use: 1. The thermal resistance of the module is very sensitive to the ambient temperature, generally used to detect the ambient temperature; 2. Through the adjustment of the potentiometer, can change the temperature detection threshold (ie, temperature control value), if necessary to control the ambient temperature is 50 degrees, the module