Dual bridge motor

L293D DUAL H-BRIDGE MOTOR DRIVER About  L293D IC generally comes as a standard 16-pin DIP (dual-in line package). This motor driver IC can simultaneously control two small motors

Dual H Bridge L298N DC Stepper Motor Drive Controller Specification: Double H bridge drive Chip: L298N (ST NEW) Logical voltage: 5 V Drive voltage: 5 V-35 V Logical current: 0 mA-36 mA Drive current: 2 A (MAX single bridge) Max power: 25 W Size:43 x 43 x 26 mm Net weight: 25 g Package weight:36 g Note: This module has a built-in 5 V power supply, when the driving voltage is 7 V-35 V, this supply is suitable for power supply DO NOT input voltage to +5 V supply interface, however ledding out 5 V for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 Lowest on | Imported | Till stocks last

DESCRIPTION Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for Arduino 1. L298N as main chip, ST corporation production. 2. Low heat,outstanding anti-interference performance. 3. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power 25w. 4. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. 5. Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply. 6. Large capacity filter capacitance,afterflow protection diode, more stable and reliable. o Specifications: 2. Double H bridge drive 3. Chip: L298N (ST NEW) 4. Logical voltage: 5V 5. Drive voltage: 5V-35V 6. Logical current: 0mA-36mA 7. Drive current: 2A(MAX single bridge) 8. Size:43 x 43 x 26mm 9. Max power: 25W 10. Net weight: 25g Uses: 11. Driving stepper motor: The connection of driving a common 4 line 2 phase electric motor is shown in figure after enable ENA ENB Input the following driving timing from IN1-IN4-then the speed and direction of the stepper motor can be controlled. 12. Driving DC motor: Because this module is driven by double H bridge,it can drive two motors simultaneously. after enable ENA ENB You can input the speed and direction of PWM signal drive motor 1 from IN1 IN2 You can input the speed and direction of PWM signal drive motor 2 from IN1 IN2 We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description L298N is a kind of high voltage, high current motor driver chip produced by ST company. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V), large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on. Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well. Features： Using L298N made by ST company as the control chip,the module has such characteristics as strong driving  ability, low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage  of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability Specification Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logical current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Size:mm Applied cases: 1) Driving stepper motor The connection of driving a common 4 line 2 phase electric motor is shown

High Ampere Dual Motor Driver H-Bridge Module   Package includes: §   1 x High ampere (4A) Dual Motor Driver module   Description: §   The motor driver module is based on MOSFETs (Metal Oxide Semiconductor Field Effect Transistor) and power transistors delivering current up to 5A (max current). §   The module has 4 inputs: “ IN A ”, “ IN B ”, “ IN C ”, “ IN D ”. §   The working logic is given below:   IN A IN B Direction 0 0 Brake 0 1 CW 1 0 CCW 1 1 Brake

Description Package Includes: 1 Piece new  Dual H Bridge DC Stepper Motor Drive Controller Board Module Arduino L298N D2

Package Contents 1 x L298N DC Driver Controller Stepper Motor smart Car Board Module Dual H Bridge DC Motor Driver Arduino PIC, Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC    Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V    Driven part of the peak current Io: 2A    The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)    The logical part of the operating current range: 0 ~ 36mA    Storage temperature: -25 Deg C ~ +130 Deg C    Other Extensions: control of direction indicators, the logic part of the plate to take power interface. Driver Board Size: 55mm * 60mm * 30mm    Drive plate Weight: 33g    Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.     Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

High Ampere (5A) Dual Motor Driver H-Bridge Kit   Package includes: § 1x High ampere (5A) Dual Motor Driver PCB § 8x Power Transistors § 4x NPN biasing transistors (2N) § Resistors: 10k Ω (0.25W), 3.3k Ω (0.25W), W), 1k Ω (0.5W) § Capacitor: 1x µf § 8x 1N diode § 3x 5mm screw terminal § 4x LED     Description: §    The motor driver module is based on MOSFETs (Metal Oxide Semiconductor Field Effect Transistor) and power transistors delivering current  up to 5A  (max current). §    The module has 4 inputs(with PWM support): “ IN A ”, “ IN B ”, “ IN C ”, “ IN D ”. §    The working logic is given below:   IN A IN B Direction 0 0 Brake 0 1 CW 1 0 CCW 1 1 Brake

Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC   Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V   Driven part of the peak current Io: 2A   The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)   The logical part of the operating current range: 0 ~ 36mA   Storage temperature: -25 Deg C ~ +130 Deg C   Other Extensions: control of direction indicators, the logic part of the plate to take power interface.Driver Board Size: 55mm * 60mm * 30mm   Drive plate Weight: 33g   Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.

THIS L293D DRIVER MODULE IS A MEDIUM POWER MOTOR DRIVER PERFECT FOR DRIVING DC MOTORS AND STEPPER MOTORS. IT USES THE POPULAR L293D MOTOR DRIVER IC. IT CAN DRIVE 4 DC MOTORS IN ONE DIRECTION, OR DRIVE 2 DC MOTORS IN BOTH THE DIRECTIONS. FEATURES AND USAGE L293D motor driver IC. Male burg stick connectors for supply, ground and input connection Screw terminal connectors for easy motor connection This motor driver is perfect for robotics and mechatronics projects for controlling motors from microcontroller, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms

Product Description Description: Double H bridge drive Chip: L298N  Logical voltage: 5V Drive voltage: 5V-35V Logical current: 0mA-36mA Drive current: 2A (MAX single bridge) Storage temperature: -20 to +135 Max power: 25W Weight: 30g Size: 43 x 43 x 27mm

This is L293D based H-Bridge motor driver board for driving DC motors and is ideal for robotics applications. PTR CONNECTORS FOR EASY CONNECTIONS USER ACCESSIBLE MOTOR ENABLE PINS FACILITY ON BOARD V POWER REGULATOR, NO NEED TO GIVE EXTERNAL 5v POWER SUPPLY ON BOARD POWER LED AND POWER ON OFF SWITCH WIRE CONNECTOR FOR INPUT SIGNAL

DESCRIPTION L293D Arduino Official Motor Drive ShieldHere is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects. 2 connections for 5V hobby servos connected to the Arduino s high-resolution dedicated timer no jitter! 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 36VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. Pull down resistors keep motors disabled during power-up Big terminal block connectors to easily hook up wires (AWG) and power Arduino reset button brought up top 2-pin terminal block and jumper to connect external power, for seperate logic/motor supplies Tested compatible with Arduino Mega, Diecimila & Duemilanove Download the easy-to-use Arduino software library, check out the examples and you re ready to go! The motor drive, can also drive 4 dc motor can be 600MA through each motor, motor can be run in to the 36V voltage between 4.5 V.Can also drive two stepper motor and two steering gear. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

L293D Arduino multi-motor control shield for arduino UNO Compatible with UNO, Mega, Diecimila & Duemilanove Product Summary:   ·         The shield contains two L293D motor drivers and one 74HC595 shift register. ·         The shift register expands 3 pins of the Arduino to 8 pins to control the direction for the motor drivers. ·         The output enable of the L293D is directly connected to PWM outputs of the Arduino. ·         The Motor Shield is able to drive 2 servo motors, and has 8 half-bridge outputs for 2 stepper motors or 4 full H-bridge motor outputs or 8 half-bridge drivers, or a combination.   Description: ·         2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter!  ·         Up to 4 bi-directional DC motors with individual 8-bit speed selection (about 0.5% resolution)  ·         Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.  ·         4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, 4.5V to12V  ·         Pull down resistors keep motors disabled during power-up  ·         Big terminal block connectors to easily hook up wires (AWG) and power  ·         Arduino reset button brought up top ·         2-pin terminal block to connect external power, for seperate logic/motor supplies  ·         compatible with UNO,Mega, Diecimila, & Duemilanove ·         Dimensions: 69mm x 53mm x 14.3mm (2.7in x 2.1in x 0.6in)   Package Include: ·         1pc. L293D Arduino multi-motor control shield Shipping Details: Our preferred shipping partners are for remote locations we prefer Indian speed post   Feedback: ·         In case you find any problem

Special Scheme BUY 4 GET 1 FREE The All new Motor Driver Shield for your Arduino. It can run 2 servo or 2 stepper or 4 DC motor with the help of external power supply and controlling via arduino. Versatile product comes from adafruit. --  2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution      dedicated timer - no jitter! --  Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%      resolution) --  Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or      micro-stepping. --  4 H-Bridges: L293D chip set provides 0.6A per bridge (1.2A peak) with thermal shutdown      protection, 4.5V to 25V --  Pull down resistors keep motors disabled during power-up --  Big terminal block connectors to easily hook up wires (AWG) and power --  Arduino reset button brought up top --  2-pin terminal block to connect external power, for separate logic/motor supplies --  Tested compatible with Mega, Diecimila, & Duemilanove now, first time Made

WELCOME TO ROBOCENTRAL***    ***IMPORTED DC- DC Buck Converter ***             ! !   YOU WILL GET SAME PRODUCT AS SHOWN IN THE PICTURE! ! ****DESCRIPTION**** Arduino is a great starting point for electronics, and with a motor shield it can also be a nice tidy platform for robotics and mechatronics. Here is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects. !!!SPECIFICATION!!! 2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter!  Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)  Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.  4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, 4.5V to12V  Pull down resistors keep motors disabled during power-up  Big terminal block connectors to easily hook up wires (AWG) and power  Arduino reset button brought up top 2-pin terminal block to connect external power, for seperate logic/motor supplies  Tested compatible with UNO,Mega, Diecimila, & Duemilanove Dimensions(assembled): 69mm x 53mm x 14.3mm (2.7in x 2.1in x 0.6in) Package Contains  1 X L293D Motor Control Shield      we value your needs           So usually ship within same business day except Sunday or public holiday's          WE AIM AT PROVIDING BEST QUALITY PRODUCT S                    ***AT LOWEST POSSIBLE RATES ***                      * **WE  USE QUALITY SHIPPING ONLY***           (TO ENSURE THAT THE PRODUCT REACHES YOU AT THE EARLIEST)         YOUR FEEDBACK IS HIGHLY VALUABLE FOR OUR BUSINESS TO GROW   **PLEASE LEAVE US THE BEST 5(STAR) RATINGS**      *********ONCE YOUR ARE SATISFIED*********   In case of any claim or complaints please contact us before leaving any neutral or negative feedback    ****And we will try our best to resolve your issue****    For Any Queries Please Call us on: / .   OR    You can email us at:            "DON'T WORRY BUY WITH CONFIDENCE"        !!!THANK'S FOR  GIVING US YOUR VALUABLE TIME!!!            **PLEASE VISIT AGAIN**

Package Contains The All new Motor Driver Shield for your Arduino. It can run 2 servo or 2 stepper or 4 DC motor with the help of external power supply and controlling via arduino. --  2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution      dedicated timer - no jitter! --  Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%      resolution) --  Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or      micro-stepping. --  4 H-Bridges: L293D chip set provides 0.6A per bridge (1.2A peak) with thermal shutdown      protection, 4.5V to 25V --  Pull down resistors keep motors disabled during power-up --  Big terminal block connectors to easily hook up wires (AWG) and power --  Arduino reset button brought up top --  2-pin terminal block to connect external power, for separate logic/motor supplies --  Tested compatible with Mega, Diecimila, & Duemilanove you can learn more at http://learn.adafruit.com/adafruit-motor-shield. There you can find FAQ, Library and many more things.... Shipping Policy Providing A Valid And Working Mobile Number Is Mandatory For Us To Dispatch Your Order. In Case If We Find That The Number Provided By You During Order Placement To Be Incorrect We Reserve The Right To Cancel The Order And Your Amount Will Be Refunded To You Through Paisapay And Your Order Will Not Be Dispatched All orders will be dispatched within 3 working days or earlier. Order once placed cannot be cancelled or modified. Normal courier delivery times are 72 hrs for metro cities and upto 10 days for other areas. These times are only indicative and the actual delivery times may vary. Octroi, if any, will be additional and to be bourne by the buyer. Octroi is not included

DESCRIPTION MatLogix Arduino Uno Board with Universal Shield The ARDUINO Board (ATMEGA 8-L) is a microcontroller board based on the ATmega 8-L. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8 up to programmed as a USB-to-serial converter. Universal Shield: Features: A monolithic integrated, high voltage, high current, 4-channel driver Using this chip you can use DC motors and power supplies of up to 36 V, so that some pretty big motors and the chip can supply a maximum current of 600mA per channel Also known as a type of H-Bridge, which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping LDR (light Sensor) for detecting the intensity of light. On board Regulated Power Supply 5v,12v supplys A Serial Port DC Power Supply Connector(12v Dc) LCD display 2x16Character Extra Vcc and Gnd Pins from which you can connect different devices. Potentiometer to set the light intensity of LCD Screen. Reset Switch to reset the arduino board. Slot for TSOP sensor. Kit Content: 1 x Arduino Uno Board 1 x 16x2 LCD (Female) 1 x L293D IC 1 x LDR 1 x USB Cable We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/