Esp serial port wifi

ESP ESP-12 Remote Serial Port WIFI Transceiver Wireless Module for arduino Description: It run LWIP bgn WIFI Direct (P2P),SOFT-AP Built-in TCP/IP The AT command is perfect,efficient,concise Support three modes: AP, STA and AP+STA coexistence mode Package Includes: 1 x ESP-12 Remote Serial Port WIFI Transceiver Wireless Module Shipping:Power Ship/Dtdc/Speed Post

ESP remote serial Port WIFI wireless module : ESP (ESP12) Module Board Its Another Arduino with free WIFI Client & Access Point FULL GPIO's Out Test Board with RGB leds, Leds to all GPIO's  Header For Sensors & Output. Jumper For Flashing Mode LDR TO Analog Input Test With Mobile / Lua Loader With PC INSTALL LUA FIRMWARE / INSTALL ARDUINO CODE ON IT / USE IT FOR WiFI ENABLE YOUR HOUSE (MAIL ME FOR HELP) How to use: 1 install IOT. APK

Description: It run LWIP bgn WIFI Direct (P2P),SOFT-AP Built-in TCP/IP The AT command is perfect,efficient,concise Support three modes: AP, STA and AP+STA coexistence mode Package included: 1 x ESP-12 Remote Serial Port WIFI Transceiver Wireless Module Powered by Turbo Lister

ESP Wifi Module Serial Wireless Send Receive Transceiver ESP-12 Description: Chip: ESP Type: ESP-12 Package Included: 1 X ESP-12

ESP Wifi Module Serial Wireless Send Receive Transceiver ESP-12 Description: Chip: ESP Type: ESP-12 Package Included: 1 X ESP-12 Shipping:: We normally ship within 2-3 business days through Bluedart, Aramex, DTDC or Speed post (for remote locations).

ESP is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functi ons from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. Corresponding Interface: SDIO 2.0, SPI, UART 32-pin QFN package Integrated RF switch, balun, 24dBm PA, DCXO, and PMU Integrated RISC processor, on-chip memory and external memory interfaces Integrated MAC/baseband processors Quality of Service management I2S interface for high fidelity audio applications On-chip low-dropout linear regulators for all internal supplies Proprietary spurious-free clock generation architecture Integrated WEP, TKIP, AES, and WAPI engines Specification: b/g/n Wi-Fi Direct (P2P), soft-AP Integrated TCP/IP protocol stack Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLLs, regulators, DCXO and power management units +19.5dBm output power

ESP serial WIFI module adapter plate with ESP-12 ESP serial WIFI module adapter plate with ESP-12 This is ESP-12 with adapter plate. You can also add 3.3v regulator to this board. Click Here  to view our other products Contact Us Shipping Payments Feedback We ship our products through reputed shipping services like Fedex, Bluedart, Aramex, DTDC etc. as per availability of the service at customers place. We accept payments only through Paisa Pay. Paisa Pay:The Easiest Way to pay for most of the items is on . We only ship the goods on the address registered with Paisa Pay. If you have any query, please feel free to contact us through "Ask a Question" link under seller information. OR Email Us at: OR Call at: +91- Your feedback is important for us to grow our business on , so please do leave a feedback. If after purchase you have any issues with the product kindly contact us and let us know, leaving a negative feedback will not solve the problem. Like Us on  Facebook 

Product Description This is a wifi solution based on IC ESP from Espressif, very price competitive wifi module, and also great function. Bring your project to the internet of things easily! Features: Very competitive price AP, STA, AP+STA modes available. Very simple AT commands, easy to use. internal LWIP interface. Only four pins interface, VCC-3V3, GND, TXD and RXD. Current firmware V091 for all stock, new reserved reset and CH_PD (for updating) pins available, you can refresh the firmware now. All using new ESPex new chip, old chip is not available anymore. Pin description Pin High Status Low Status Note VCC, GND Use standalone power source, or large capacitor, all power of this module from external TXD, RXD The serial port RST - restart CH_PD Flash boot and Update Mode - chip enable, so always connect to high status with VCC GPIO0 - Update mode GPIO2 - - GPIO 15 (when avaialble) NC Flash boot Mode Only for a few version, Wi07-3 GPIO 12 GPIO 13 GPIO 14 GPIO 16 Hardware RST No need any pull-up AT commands §   Baud rate: (from v0.90, v0.80 and older: ) §   The AT part of the command can be written large or small, however, the following command must always be written large §   Make sure that before, after and within the command no spaces (space) occur General AT commands AT command Description Parameter Example AT Test command, are always "OK" back AT AT + RST Reset of the module, the module's boot messages followed by  ready  back AT + RST AT + GMR Querying the Firmware Version AT + GMR WiFi AT commands AT command Description Parameter Example AT + CWMODE =  Setting the WiFi mode  1) Station 1 =  2 = Access Point  3 = Both AT + CWMODE = 1 AT + CWMODE? Query WiFi mode AT + CWMODE? AT + CWMODE =? Query of possible settings for WiFi mode AT + CWMODE =? AT + CIPMUX = Using multiple connections 0 = single compound  1 = Multiple connections AT + CIPMUX = 1 AT + CIPMODE = Setting the data mode 0 = transparent  1 = Data AT + CIPMODE = 1 AT + CIPMODE? Output of the data set mode AT + CIPMODE? WiFi commands (Station / client) AT command Description Parameter Example AT + CWJAP =, Connecting to WiFi network ssid "SSID"  pass "password" AT + CWJAP = "makerday", "M4k3rd4y" AT + CWJAP? Output of the currently connected WiFi network AT + CWJAP? AT + CWLAP Output of available APs  2) AT + CWLAP AT + CWQAP Closes the connection to an access point AT + CWQAP AT + CIFSR Issue its own IP address AT + CIFSR WiFi commands (Access Point) AT command Description Parameter Example AT + CWSAP =, [,,] Set the access point parameters  3) ssid "SSID"  pass "password"  chan "channel"  enc "Encryption"  (0 = Open  1 = WEP  WPA_PSK 2 =  3 = WPA2_PSK  4 = WPA_WPA2_PSK) AT + CWSAP = "makerday", "M4k3rd4y" 5.3 AT + CWSAP? Output the current settings for the AP AT + CWSAP? AT + CWLIF Lists stations connected IPs 4) AT + CWLIF WiFi commands (IP Client) AT command Description Parameter Example AT + CIPSTATUS Output status of the IP connection (s) AT + CIPSTATUS AT + CIPSTART =,, Creating an IP connection with AT + CIPMUX = 0 type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND = Sending data over a single compound  5) len: Data length AT + CIPSEND = AT + CIPCLOSE Close a single TCP or UDP connection AT + CIPCLOSE AT + CIPSTART =,,, Creating an IP connection with AT + CIPMUX = 1 id: 0-4  type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND =, Send data via merhere compounds 6) id: 0-4  len: Data length AT + CIPSEND = AT + CIPCLOSE = Close one of several TCP or UDP connection id: 0-4 AT + CIPCLOSE = 1 WiFi commands (IP server) AT command Description Parameter Example AT + CIPSERVER = 1 [,] Starts the TCP server port: TCP port AT + CIPSERVER = AT + CIPSERVER = 0 Terminates the TCP server AT + CIPSERVER = 0 AT + CIPSTO = Sets timeout for TCP server timeout = s AT + CIPSTO = 180 AT + CIPSTO? Specifies timeout of TCP server AT + CIPSTO? If a TCP server is started, it can handle up to 5 simultaneous connections. Other compounds can be created, but only served when others are closed or terminated by timeout. The module incoming data directly with the prefix  + IPD  issued: + IPD,   OK   + IPD, 0.6: ON   OK The output is divided as follows: + IPD,,, It is  id  the ID of the compound (0-5),  len  the length of the resulting data packet and  data  contains the data received from the client. In the above example as first sends compound 1 the value   and then connect the string 0  ON     Powered by Turbo Lister

Product Description This is a wifi solution based on IC ESP from Espressif, very price competitive wifi module, and also great function. Bring your project to the internet of things easily! Features: Very competitive price AP, STA, AP+STA modes available. Very simple AT commands, easy to use. internal LWIP interface. Only four pins interface, VCC-3V3, GND, TXD and RXD. Current firmware V091 for all stock, new reserved reset and CH_PD (for updating) pins available, you can refresh the firmware now. All using new ESPex new chip, old chip is not available anymore. Pin description Pin High Status Low Status Note VCC, GND Use standalone power source, or large capacitor, all power of this module from external TXD, RXD The serial port RST - restart CH_PD Flash boot and Update Mode - chip enable, so always connect to high status with VCC GPIO0 - Update mode GPIO2 - - GPIO 15 (when avaialble) NC Flash boot Mode Only for a few version, Wi07-3 GPIO 12 GPIO 13 GPIO 14 GPIO 16 Hardware RST No need any pull-up   AT Commands Format Baud rate at (new line) use option "send new line" or 'carriage return' for each command x is the commands Set Inquiry Test Execute AT+ = AT+ ? AT+ =? AT+ AT+CWMODE= AT+CWMODE? AT+CWMODE=? - Set the network mode Check current mode Return which modes supported - Commands carefully there are must be no any spaces between the " and IP address or port Commands Description Type Set/Execute Inquiry test Parameters and Examples AT general test basic - - - - AT+RST restart the module basic - - - - AT+GMR check firmware version basic - - - - AT+CWMODE wifi mode wifi AT+CWMODE= AT+CWMODE? AT+CWMODE=? 1= Sta, 2= AP, 3=both, Sta is the default mode of router, AP is a normal mode for devices AT+CWJAP join the AP wifi AT+ CWJAP =, AT+ CWJAP? - ssid = ssid, pwd = wifi password AT+CWLAP list the AP wifi AT+CWLAP AT+CWQAP quit the AP wifi AT+CWQAP - AT+CWQAP=? AT+ CWSAP set the parameters of AP wifi AT+ CWSAP=,,, AT+ CWSAP? ssid, pwd, chl = channel, ecn = encryption; eg. Connect to your router: AT+CWJAP="www.shanrittech.com","helloworld"; and check if connected: AT+CWJAP? AT+CWLIF check join devices' IP wifi AT+CWLIF - - AT+ CIPSTATUS get the connection status TCP/IP AT+ CIPSTATUS,,,, = client or server mode AT+CIPSTART set up TCP or UDP connection TCP/IP 1)single connection (+CIPMUX=0) AT+CIPSTART=,,; 2) multiple connection (+CIPMUX=1) AT+CIPSTART=,, - AT+CIPSTART=? id = 0-4, type = TCP/UDP, addr = IP address, port= port; eg. Connect to another TCP server, set multiple connection first: AT+CIPMUX=1; connect: AT+CIPSTART=4,"TCP","X1.X2.X3.X AT+CIPMODE set data transmission mode TCP/IP AT+CIPMODE= AT+CIPSEND? 0 not data mode, 1 data mode; return "Link is builded" AT+CIPSEND send data TCP/IP 1)single connection(+CIPMUX=0) AT+CIPSEND=; 2) multiple connection (+CIPMUX=1) AT+CIPSEND=, AT+CIPSEND=? eg. send data: AT+CIPSEND=4,15 and then enter the data. AT+CIPCLOSE close TCP or UDP connection TCP/IP AT+CIPCLOSE= or AT+CIPCLOSE AT+CIPCLOSE=? AT+CIFSR Get IP address TCP/IP AT+CIFSR AT+ CIFSR=? AT+ CIPMUX set mutiple connection TCP/IP AT+ CIPMUX= AT+ CIPMUX? 0 for single connection 1 for multiple connection AT+ CIPSERVER set as server TCP/IP AT+ CIPSERVER= [,] mode 0 to close server mode, mode 1 to open; port = port; eg. turn on as a TCP server: AT+CIPSERVER=, check the self server IP address: AT+CIFSR=? AT+ CIPSTO Set the server timeout AT+CIPSTO= AT+CIPSTO?

Description Package Includes: 1 Piece new  ESP Serial WIFI Wireless Transceiver Module Send Receive AP+STA for Arduino It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description Package Includes: "", INDEX('Name Master'!C[0]:C[0], MATCH(R[0]C[-1],'Name Master'!C[-1]:C[-1],0)),"")">1pcs  "", INDEX('Name Master'!C[0]:C[0], MATCH(R[0]C[-1],'Name Master'!C[-1]:C[-1],0)),"")">ESP serial WIFI module Original test plate + WIF sending and receiving wireless module Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  by PhraseFinder" style="border: none !important; display: inline-block !important; text-indent: 0px !important; float: none !important; font-weight: bold !important; height: auto !important; margin: 0px !important; min-height: 0px !important; min-width: 0px !important; padding: 0px !important; text-transform: uppercase !important; text-decoration: underline !important; vertical-align: baseline !important; width: auto !important; background: transparent !important;"> Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

ESP   ESP is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.     Features:   - SDIO 2.0, SPI, UART -  32-pin QFN package -  Integrated RF switch, balun, 24dBm PA, DCXO, and PMU -  Integrated RISC processor, on-chip memory and external memory interfaces -  Integrated MAC/baseband processors -  Quality of Service management -  I2S interface for high fidelity audio applications -  On-chip low-dropout linear regulators for all internal supplies -  Proprietary spurious-free clock generation architecture -  Integrated WEP, TKIP, AES, and WAPI engines     Solutions -  Supports APSD for optimal VoIP applications -  Patented spurious noise cancellation algorithm for integration

Product Description Smallest do about mm, the size of a fingernail. Easily embedded into any product   Powerful internal protocol run LWIP   Supports three modes: AP, STA, AP + STA coexistence mode   AT commands perfect simple and efficient, allowing you to develop easier.

Product Description Smallest do about mm, the size of a fingernail. Easily embedded into any product   Powerful internal protocol run LWIP   Supports three modes: AP, STA, AP + STA coexistence mode   AT commands perfect simple and efficient, allowing you to develop easier. This Item is Sealed Item so I cannot give guarantee/warranty for this product.  I can give guarantee if i am selling

ESP ESP-201 Remote Serial Port WIFI Transceiver Wireless Module Description: Can be use as full IO module Package included: 1 x ESP-201 Remote Serial Port WIFI Transceiver Wireless Module

This is WiFi serial transceiver module, based on ESP SoC.   The SOC has Integrated TCP/IP protocol stack   We have a set of documents

Description ESP   ESP is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.     Features:   - SDIO 2.0, SPI, UART -  32-pin QFN package -  Integrated RF switch, balun, 24dBm PA, DCXO, and PMU -  Integrated RISC processor, on-chip memory and external memory interfaces -  Integrated MAC/baseband processors -  Quality of Service management -  I2S interface for high fidelity audio applications -  On-chip low-dropout linear regulators for all internal supplies -  Proprietary spurious-free clock generation architecture -  Integrated WEP, TKIP, AES, and WAPI engines     Solutions -  Supports APSD for optimal VoIP applications -  Patented spurious noise cancellation algorithm for integration

Description Features: ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime b/ g/ n Technical parameters: Support 3 Modes: AP, STA, AP+STA Power down leakage current of Wake up and transmit packets

ESP ESP-12E Serial WiFi Wireless Transceiver SMD Module with ADC, SPI and Extra Pinouts ESPE is an enhanced version ESP, improve peripheral circuitry increases impedance matching, the signal output is better, whether it is stable or anti-jamming capability, have been greatly improved! For users before selecting the ESP-12, it does not matter even if the product has been made, enhanced version is fully compatible with previous firmware, the pin has added six IO ports on the basis of the ESP-12, SPI leads. ESP is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. Features: SDIO 2.0, SPI, UART 32-pin QFN package Integrated RF switch, balun, 24dBm PA, DCXO, and PMU Integrated RISC processor, on-chip memory and external memory interfaces Integrated MAC/baseband processors Quality of Service management I2S interface for high fidelity audio applications On-chip low-dropout linear regulators for all internal supplies Proprietary spurious-free clock generation architecture Integrated WEP, TKIP, AES, and WAPI engines Solutions: Supports APSD for optimal VoIP applications Patented spurious noise cancellation algorithm for integration

ESPE is an enhanced version ESP, improve peripheral circuitry increases impedance matching, the signal output is better, whether it is stable or anti-jamming capability, have been greatly improved! For users before selecting the ESP-12, it does not matter even if the product has been made, enhanced version is fully compatible with previous firmware, the pin has added six IO ports on the basis of the ESP-12, SPI leads. ESP is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. Features: SDIO 2.0, SPI, UART 32-pin QFN package Integrated RF switch, balun, 24dBm PA, DCXO, and PMU Integrated RISC processor, on-chip memory and external memory interfaces Integrated MAC/baseband processors Quality of Service management I2S interface for high fidelity audio applications On-chip low-dropout linear regulators for all internal supplies Proprietary spurious-free clock generation architecture Integrated WEP, TKIP, AES, and WAPI engines Solutions: Supports APSD for optimal VoIP applications Patented spurious noise cancellation algorithm for integration