Microchip pic development board

Package Contents   1 x PIC development Board with Free USB cable and CD containing software examples.   External Power supply NOT Included.    Contact Details   Have any Queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"    The PIC development board is a microcontroller board based on the PIC16F877. It has 33 input/output pins and two PWM outputs, 8 (10 bit) analog inputs, a works upto 20 MHz speed. A USB connection is available for programming and UART (communication with the PC), an external power jack is provided for high current motor applications etc. A Reset button is present. A 4 x 4 key matrix is provided for keyscan applications. A 16 x 2 LCD with programmable backlight is provided. A Piezo Buzzer is present. A 4 digit 7 segment common cathode display is populated for display multiplexing example. A onboard potentiometer is provided on one analog channel. A coin cell battery backed DS (RTC) is present on one of the I2C channel. An optional SPI external EEPROM (not provided with the board) can be mounted by the user for SPI memory. A ULN based stepper motor interface is present.   The Board contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. FEATURES AND USAGE The maximum length and width of the Board is approx 7 inch by 5.5 inches. Four PCB studs allow the board to be attached to a surface or act like a support stand. All the ports of the microcontroller are available as edge connectors on the right side of the board on a standard 100 mil spacing. The board can also take most of the 40 Pin DIP PIC18 series microcontrollers. An External programmer may be needed

The PIC DEVELOPMENT board demonstrates the capabilities of Microchip’s 8-bit microcontrollers, specifically, 18-, 28- and 40-pin PIC16FXXX, PIC16F1XXX, and PIC18 devices.  It can be used as a standalone demonstration board with a programmed part. Alternatively, it can be used with an in-circuit emulator (for example, MPLAB® Real ICETM) or with an in-circuit programmer/debugger (such as MPLAB® ICD 3 or PICkitTM 3). Microchip offers a bundle of the PICDEM 2 PLUS and the MPLAB® ICD 3, called the MPLAB® ICD 3 Evaluation Kit (with PICDEM 2 Plus), product number DV164036. Sample programs are provided to demonstrate the unique features of the supported devices.       Key Components  LCD display Interface 40 pin socket 4x LEDs four 7 segment display  RS232 interface to PC 12 V adapter connector GPIO Pin connector 4 * 4 switch matrix On-board external oscillators Four push button switches for external stimulus and reset Variable voltage input for ADC simulation Connectivity options Programmer/debugger connectivity using MPLAB ICD 3, MPLAB Real ICE and PICkit 3 PICkitTM Serial Connector for analysis of serial communications peripherals such as SPI or I2C Active RS 232 port Expansion

Universal Development Board for Arduino, , PIC, AVR and ARM7, Raspburry Pi   (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL       Product Overview   1.     About Digital and Analog IO Interfacing Board                                                                    If you are learning any microcontroller than input and output circuit is always important to experiment with any microcontroller. Digital and Analog IO Board is suitable for quick experiment with any microcontroller.   2.     Features Digital and Analog IO Interfacing Board having a following features:                                                               ·          Eight LEDs ·          Four Switches ·          One LDR (Light Dependent Resistor) (Light Sensor) ·          One Temperature Sensor (LM35) (Sensor) ·          One Variable Resistor (Preset/POT) (Sensor) ·          One Infrared receiver (TSOP) (Remote Control Sensor) ·          One Buzzer ·          One Relay Categories into Inputs/Outputs 1.        Digital Inputs ·          Switches ·          Infrared receiver (TSOP.        Analog Inputs ·          Variable Resistor ·          LDR ·          Temperature Sensor 3.       Digital and Analog Outputs ·          LEDs ·          Buzzer ·          Relay Dimensions (LxWxH) - Cms: 6.5 CM X 6.5CM Datasheet:  http://www.mediafire.com/view/6c3dmdhpw3rlwdh/Digital_and_Analog_IO_Board.pdf

See our ratings Add this shop to my favorites PIC12F675 PIC Microcontroller Development Board with 2 Relays and 3 Analog Inputs ₹ Availability:

Description: Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two Two on-board relay which can switch up to 7Amps. Relays terminals (COM, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free-wheeling diode which will further protect your microcontroller from relay kick back. This is a 5V 2-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.    Features: 1.     Equipped with high-current relay 7A@250VAC / 10A@24VDC.  2.     It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. 3.     High quality screw terminals (Terminal Block) provided (COM, NC, NO) for quick and easy connection. 4.     Free wheeling diode to protect your microcontroller. 5.     Input Signal Pin connected to Burg stick for easy accessibility. 6.     LED Status indicators to indicate the relay ON/OFF status. 7.     Mounting holes provided. Package Contains: 1.      1 x Two channel 5V relay Module.    

See our ratings Add this shop to my favorites PIC16F877A PIC Microcontroller Mini Breakout Development Board ₹ Availability:

Package Contents 1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has one (1) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free wheeling diode which will further protect your microcontroller from relay kick back. This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Free wheeling diode to protect your microcontroller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four (4) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has 2 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two (2) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and Transistor will further protect your micro-controller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - BC 547 Transistor used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

The low-cost PICKIT 2 Programmer/Debugger can program Microchip Flash PIC MCU's including PIC10F, PIC12F, PIC16F, PIC18F, PIC24F, dsPIC30 and dsPIC33 families. Supports read and write operation for serial EEPROM's e.g. 11LCXX, 24LCXX, 25LCXX, 93LCXX, KEELOQ HCS and MCP250xx CAN Devices. USB port powered & no external power supply is required. Adjustable Voltage source (2.5V to 5.0V) with auto-detection and auto-selection. In-Circuit-Debugging & Programming of supported Device Families with MPLAB IDE: PIC10F, PIC12F, PIC16F, PIC18F, PIC24, dsPIC30, dsPIC Breakpoints, depending on MCU * Run, Halt, Step In, Step Over Supports Programmer-To-Go (Standalone Programmer) feature when memory chips are installed Also includes USB-UART (Serial) Tool, Logic I/O Tool & Logic Analyzer microcontroller development utilities. PICkit 2 UART Tool can be used to -  Display debug text output from the target MCU  Log microcontroller data to a text file  Developing and debugging a microcontroller UART interface  Interfacing with and sending commands to the microcontroller during development All PIC32MX & PIC32MZ family chips can be programmed by using PIC32Prog software. Can also program ATmega chips by using a special software.

      The USB to RS232 converter board is most essential bridge needed to connect serial device to log the data to pc or laptop. If you have a development board like 8051, AVR, PIC or any other with serial UART or RS232 connector. Then use the USB to RS232 converter to connect these devices for programming or communication with the PC or Laptop.              Now a days most of the laptops does not have COM ports to connect directly with RS232 cable. So use i-labz USB to RS232 converter for interfacing. If you are planning to buy 8051, AVR, PIC or any other boards like GSM modem, GPS, Bluetooth, Finger print scanner or Ultrasonic distance finder then you must use USB to RS232 connector for connecting or troubleshooting with laptop. CP210x Driver Installation Guide - USB Driver Installation Instructions Download Terminal tool for Troubleshooting(winXP/7/8)               To test the USB to RS232 converter use windows hiighper terminal (using winXP as OS) or terminal tool. The procedure to test to setup the highper terminal is explained

About: Have a Micro-controller and a development board(Arduino, Freeduino, , AVR or PIC), But having a hard time with no components OR finding components? Right here! is the solution.  This "Micro-controller components kit" includes all the components needed to learn all the basics about the micro-controller you have. NOTE:  This kit does NOT include any Development Board, Instead it has components needed to learn about micro-controllers.  Package includes: Product Quantity 01.  Battery snap .  DC jack(9V) .  B read-board(Medium sized with 640 tie-in Points) .  Motor w/ Fan 01 each 05.  Potentiometer(pot - 22kOhm) .  Capacitors(100uF, 22uF, 10uF and 1uF) 05 each 07.  LED's(White, Red, Green and Blue) 05 each 08.  IR pai r(IR-Emitter and IR-Sensor) 02 each 09.  7-segment display .  Push buttons    .  Transistors(BC547 and BC each 12.  LDR(Light Dependent Resistor - also called Photo-resistor) .  Regulator( and LM each 14.  Resistance box(all standard values - Upto 20 different values)     01 box 15.  LCD display(16x.  F-F wires(4 different colors) 05 each 17.  Single strand wires(5 different colors) 03 each