Mma accelerometer module

ADXL345 Triple-Axis Digital Accelerometer   Module ADXL345 can be used with AVR, ARM, PIC via SPI   Description:   The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.   Features: Digital Output: SPI / I2C Ultralow power: as low as 23 μA

Description This is a breakout board for Freescale’s MMAL three-axis analog MEMS accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices. Two selectable measuring ranges (±1.5g, ±6g) Breadboard friendly - 0.1" pitch header Low current consumption: 400 µA Sleep mode: 3 µA This breadboard friendly board breaks out every pin of the MMAL to a 9-pin, 0.1" pitch header. The sensor works on power between 2.2 and 3.6VDC (3.3V optimal), and typically consumes just 400µA of current. All three axes have their own analog output. Technical parameters: Voltage Range- DV Static Current- Output Level- High 3.3 V /Low 0V Working Temperature- -  deg   Package Includes: 1 Piece new  MMA  Accellerometer Module 3 Axis  Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

WELCOME TO ROBOCENTRAL***    ***IMPORTED  GY-521 MPU- Module 3 Axis Gyroscope + Accelerometer for Arduino   ***             ! !   YOU WILL GET SAME PRODUCT AS SHOWN IN THE PICTURE! ! !!!Description!!! MPU- module (Three Axis Gyro + Three Axis Acceleration) Chip used: MPU-  Power supply: 3-5 v (internal low voltage difference voltage stabilizing)  Communication: standard IIC communication agreement  Chip In-built 16 bit AD converter, 16 bits of data output  The gyroscope range: + degree /sec  Acceleration range: ± 2g ± 4g ± 8g ± 16 g  Net weight:3 g  Package weight:13 g  The MPU- is a high precision piece of motion processing tech. By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an on board Digital Motion Processor™ (DMP™) capable of processing complex 9-axis Motion Fusion algorithms MPU- does away with the cross-axis alignment problems that can creep up on discrete parts. Auxiliary master I2C bus which allows the MPU- to access external magnetometers and other sensors. Note: V oltage rating should not exceed V. Package Contains                                                                               1 X   MPU- Module                                                            2 x sets of header pins        we value your needs           So usually ship within same business day except Sunday or public holiday's          WE AIM AT PROVIDING BEST QUALITY PRODUCT S                    ***AT LOWEST POSSIBLE RATES ***                      * **WE  USE QUALITY SHIPPING ONLY***           (TO ENSURE THAT THE PRODUCT REACHES YOU AT THE EARLIEST)         YOUR FEEDBACK IS HIGHLY VALUABLE FOR OUR BUSINESS TO GROW   **PLEASE LEAVE US THE BEST 5(STAR) RATINGS**      *********ONCE YOUR ARE SATISFIED*********   In case of any claim or complaints please contact us before leaving any neutral or negative feedback    ****And we will try our best to resolve your issue****    For Any Queries Please Call us on: / .   OR    You can email us at:            "DON'T WORRY BUY WITH CONFIDENCE"        !!!THANK'S FOR  GIVING US YOUR VALUABLE TIME!!!            **PLEASE VISIT AGAIN**

Description This is a breakout board for Freescale’s MMA7361L three-axis analog MEMS accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices. Two selectable measuring ranges (±1.5g, ±6g) Breadboard friendly - 0.1" pitch header Low current consumption: 400 µA Sleep mode: 3 µA This breadboard friendly board breaks out every pin of the MMA7361L to a 9-pin, 0.1" pitch header. The sensor works on power between 2.2 and 3.6VDC (3.3V optimal), and typically consumes just 400µA of current. All three axes have their own analog output. Technical parameters: Voltage Range- 4.5-20DV Static Current- Output Level- High 3.3 V /Low 0V Working Temperature- -15-+70  deg   Package Includes: 1 Piece new  MMA7361  Accellerometer Module 3 Axis  Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

6DOF MPU- Module 3 Axis Gyroscope+Accelerometer Module for Arduino MPU DOF MPU- Module 3 Axis Gyroscope+Accelerometer Module for Arduino MPU The MPU- is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU- does away with the cross-axis alignment problems that can creep up on discrete parts. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel. Therefor it captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with the Arduino. The MPU- is not expensive, especially given the fact that it combines both an accelerometer and a gyro. Specifications Chip: MPU- Power supply: 3V-5V power(internal low dropout regulator) Gyroscope range: + ° / s Acceleration range: ± g Communication Mode: standard IIC communication protocol Chip built-in 16 bit AD converter, 16 bits data output Pin pitch 2.54 mm Size: 20.3mm x 15.6mm For more information on its use with arduino you can visit arduino website  Click Here Click Here  to view our other products Contact Us Shipping Payments Feedback We ship our products through reputed shipping services like Fedex, Bluedart, Aramex, DTDC etc. as per availability of the service at customers place. We accept payments only through Paisa Pay. Paisa Pay:The Easiest Way to pay for most of the items is on . We only ship the goods on the address registered with Paisa Pay. If you have any query, please feel free to contact us through "Ask a Question" link under seller information. OR Email Us at: OR Call at: +91- Your feedback is important for us to grow our business on , so please do leave a feedback. If after purchase you have any issues with the product kindly contact us and let us know, leaving a negative feedback will not solve the problem. Like Us on  Facebook 

Description This module using microarray of MPU-. The Communication with all registers of the device is performed using either I2C at 400kHz or SPI at 1MHz (MPU- only). For applications requiring faster communications, the sensor and interrupt registers may be read using SPI at 20MHz (MPU- only). Additional features include an embedded temperature sensor and an on-chip oscillator with ±1% variation over the operating temperature range. Very Simple More reliable Easy to use The part features a robust g shock tolerance, and has programmable low-pass filters for the gyroscopes, accelerometers, and the on-chip temperature sensor. Technical parameters: Power supply: 3-5v (stable internal low voltage) Acceleration range: + g The spacing of the pins: 2.54mm X, Y, Z output   Package Includes: 1 Piece new  MPU- Module 3 Axis Gyroscope + Accelerometer GY521 Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description This module using microarray of MPU-6050. The Communication with all registers of the device is performed using either I2C at 400kHz or SPI at 1MHz (MPU-6000 only). For applications requiring faster communications, the sensor and interrupt registers may be read using SPI at 20MHz (MPU-6000 only). Additional features include an embedded temperature sensor and an on-chip oscillator with ±1% variation over the operating temperature range. Very Simple More reliable Easy to use The part features a robust 10,000g shock tolerance, and has programmable low-pass filters for the gyroscopes, accelerometers, and the on-chip temperature sensor. Technical parameters: Power supply: 3-5v (stable internal low voltage) Acceleration range: + 2 + 4 + 8 + 16g The spacing of the pins: 2.54mm X, Y, Z output   Package Includes: 1 Piece new  MPU-6050 Module 3 Axis Gyroscope + Accelerometer GY521 Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description: The MPU- is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU- does away with the cross-axis alignment problems that can creep up on discrete parts. Our breakout board for the MPU- makes this tiny QFN package easy to work into your project. Every pin you need to get up and running is broken out to 0.1" headers, including the auxiliary master I2C bus which allows the MPU- to access external magnetometers and other sensors. Features: I2C Digital-output of 6 or 9-axis MotionFusion data

Technical Specifications The ADXL335 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned voltage outputs.  The product measures acceleration with a minimum full-scale range of ±3 g.  It can measure the static acceleration of gravity

ADXL-345 Triple Axis Acceleration Module for Arduino and other MCU ADXL-345 Triple Axis Acceleration Module for Arduino and other MCU The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is acces-sible through either a SPI (3- or 4-wire) or I2C digital interface.  The ADXL345 is well suited for mobile device applications. It measures the static acceleration of gravity

10DOF HMCL MPU GYROSCOPE ACCELERATION COMPASS MWC FLIGHT CONTROL SENSOR MODULE Works with ARDUINO   Product Description 3 Sensors

Company Name: Naksh Researcher & Designer Centre Company Type: Hardware & Software Design in Electronics & Electrical Company Service Area: Microcontroller Based Electronics Projects, Readymade Electronics & Electrical Projects, Electronics IEEE Projects, Electronics Project list, , AVR, PIC Microcontroller, GSM, RFID, DTMF, Robotics, Touch Screen Based Projects, Real Time Electronics Projects, Final Year Electronics Projects, Major & Minor Electronics Projects Electronics & Communication Engineering Projects, Electronics & Electrical Engineering Projects, Electronics Hardware & Software Projects Final Year Major & Minor Projects Field 1. RFID Based Projects 2. DTMF Based Projects 3. GSM Based Projects 4. GPS Based Projects 5. Display Based Projects 6. Robotics Based Projects 7. Remote Control Based Projects 8. Wireless Control Projects 9. Zigbee/Bluetooth Projects 10. Automation Projects 11. Security & Surveillance Projects 12. SCADA Based Projects Keywords Microcontroller , AVR, PIC, LCD, Sensors, Relay, LED, Rectifier, Potentiometer, Resistance, capacitor, Memory, RAM, ROM, UART, RS232, SPI, ADC, Temperature, Accelerometer, RS485, CAN, LIN, I2C, Robotics, GSM 900A, SIM300, GPS, DTMF, Antenna, Wireless, RF Module, Bluetooth, DC motor, stepper Motor, Power supply, regulators etc If you have any idea for any project please feel free to contact us. Contact No: (Mobile), (Land Line)

Broadcom WICED™ Sense Bluetooth Smart Sensor Development Kit Broadcom's WICED™ Sense Bluetooth Smart Sensor Development Kit is a kit for the WICED SMART product family based on BCMS SIP module featuring Bluetooth Smart technology. The kit has an associated Smartphone app and reduces the design time for Bluetooth app development or demo from months to minutes. With six MEMs sensors on board, customers can quickly ramp a demo/prototype specific to their needs. The over-the-air download feature provides the ability to update the tag's firmware from a central device like a smartphone, tablet or PC. Features BCMS SIP with Bluetooth Smart technology Six MEMS Sensors Gyroscope Accelerometer eCompass Pressure sensor Humidity & temperature Associated smartphone app interfaces with the Development kit to allow for reduced development time Applications Internet-of-Things development MEMs Sensor development Kit Includes One WICED Sense Tag One USB to MicroUSB cable Quick Start Guide Links to download sample applications and Smart Software Development Kit 2.x             Kit Components

Description The ArduPilot Mega 2.6 allows the user to turn any fixed, rotary wing or multirotor vehicle (especially multicopters and rovers) into a fully autonomous vehicle;capable of performing programmed GPS missions with waypoints1. 3.3V or 5.0V DC power supply 1. Arduino and ArduPilot Mega 2.5 Compatible! 2. Includes both right angle and straight pins for I/O, allowing user to customize as needed. 3, Onboard 4 MP Dataflash chip for automatic datalogging 4. Invensense/'s 6 DoF Accelerometer/Gyro MPU-6000. 5. Atmel/'s ATMEGA2560-16AU and ATMEGA32U-2 chips for processing and usb functions respectively. 6. Barometric pressure sensor upgraded to MS5611-01BA03, from measurement specialties Note1: The Power Module is only designed to power APM, a RC receiver and APM accessories (GPS, Telemetry radio). It is not designed to power servos. Use your aircraft/'s own ESC/BEC for that. Note2: the use of electric power transfer: the need to JP1 jumper plug, power supply voltage does not exceed 5.6V, not less than five using UEBC: The UEBC power output cable plugged into the receiver INPUTS port, power supply is not higher than 5.2 is not lower than 4.8V Technical parameters:   Material: Plastic, Copper Main Color: Black Size: 70*44*13 mm Net weight: 38g Color: As shown