Pin board

Set of 4 Pcs AVR40 Base Board  Kit.  For Electronic project.  Atmel AVR - 40 Pin Base Boar d (For ATmega16, AT mega 32,Microcontroller) 1 Pcs 6 Digital Sensors Board for Line Follower    1 Pc 16X2 LCD Board for Display 1 Pc L298N Dual H-Bridge Motor Driver Board. **FREE**4 Pcs FRC Cable. ** Does not Include Any Microcontroller ** Atmel AVR - 40 Pin Base Board AVR-40Pin Development Board -For 40 pin AVR like ATMEGA16, ATMEGA32 etc it Comes without   micocontroller 1 Pc L298N Dual H-Bridge Motor Driver Board. 6 Digital IR - Photodiode Sensors Array for LFR Robot 6 IR-Photodiode Sensors Array- for Line following robot (LFR) and micro-mouse robot  (Digital out, Independent Manual Adjustable) Ideal for LFR (line-follower Robot) obstacles avoiding robots obstacles chasing robot side wall sensor maze solving robots 16x2 LCD Display Board Box Header Connection > LCD Connection (4Bit Mode) Pin#1   > RS(4) Pin#2   > EN(6) Pin#3   > D4(11) Pin#4   > D5(12) Pin#5   > D6(13) Pin#6   > D7(14) Pin#7   > No Connection Pin#8   > No Connection Pin#9   > Gnd () Pin#10 > +5V (2) Note Pin#5 of LCD (RW) is forcefully connected to Ground L298N Dual H-Bridge Motor Driver Board New Improved L298 Dual H-Bridge Board - Ideal for robot motor control, smart  full feature,compact, Compatible with AVR - 40 Board 10 Pin Box Header Connection Description Pin1= ENABLE B Pin2= ENABLE A Pin3= INPUT-3 Pin4= INPUT-1 Pin5= INPUT-4 Pin6= INPUT-2 Pin7= NOT CONNECTED Pin8= NOT CONNECTED Pin9= Ground Pin10=Vcc +5Volt    Fore More Details please refer Datasheet of L298N. ****FREE**** 4 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm. ,with female connectors on both ends. Please Clear Any Doubts "BEFORE" Buying any products form us. Fast Shipping via*      * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post. Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                                                        For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline: Powered by Turbo Lister

Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board. Shipping: by speed post plz make sure speed post service is available at your city, generally takes 3-7 days to deliver after getting cleared payment Feedback: plz give 5 star ratings and positive feedback its very important for us

use coupon  COUPONDUN8 to get 7.5 % off Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board. Shipping: always free by speed post please make sure speed post service is available at your city, generally takes 3-7 days to deliver after getting cleared payment Feedback: please  give 5 star ratings and positive feedback it's very important for us

Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board. Shipping: always free by speed post please make sure speed post service is available at your city, generally takes 3-5 days to deliver after getting cleared payment Feedback: please  give 5 star ratings and positive feedback it's very important for us

100 % GENUINE!!!  IMPORTED!!!  QUALITY CHECKED!!! LIMITED STOCK LOWEST PRICE CHALLENGE!!! Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1 pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board.  SHIPPING: all over india By speed post  (plz make sure speed post service is available at your city), generally takes 3-7 days to deliver FEEDBACK: PLZ GIVE 5 STAR RATINGS AND  POSITIVE  FEEDBACK  IT'S VERY IMPORTANT FOR US 100% positive feedback and satisfaction of buyers are our moto

SOIC8 SOP8 Chip IC test clip adapter board cable BIOS EEPROM spare parts SOP8 SOIC8 test clips. Perfect for read write sop8 ICs   Product Description: ·         SOP8/SOIC8 clip provides a convenient way to read or write SOP8/SOIC8 chips. ·         By this IC clip, it is not necessary to desolder the chip from the board to reprogram it or to read it.  ·         It is also not necessary when you are programming new chips (for example BIOS chips) to solder these chips on a SOP8 / SOIC8 adapter board.  ·         This IC clip is a perfect addition to a programmer   Technical specifications:   ·         High Quality IC Clip for SOP8 and SOIC8 chip packages   ·         Adapter board for SOP8 und SOIC8 chip packages ·         cable length: 28cm   Usage Instruction:   1.      The first pin of chip corresponds to red marked wire and first pin of PCB pin header identify correspond to the first pin of Programming device. 2.      Press the clip tail with your finger first, you can see the metal shrapnel when the clip is open and stretch it to the appropriate width for catching the chip. 3.      The top will stick to the PCB and the metal shrapnel should align with the PIN of IC before clamping, then relax your fingers slowly 4.      Metal shrapnel will be pushed into the plastic as the clip is closing and the clips will be clenched with plastic sheet by IC. 5.      You have to adjust the clip when it is not

Arduino uno r3 development board with ATmega328p CH340G Arduino clone based on current open source hardware Arduino uno Atmega 328p smd ideal for prototyping Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.   Product Summary arduino uno: ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz         Features of arduino uno: ·         Replaced the expensive 16u2 with CH340G chip to avoid the driver compatibility problem which was found on some win7/win8 OSes. ·         Increased the extra pin holes to facilitate the use of DuPont line cables, with some extra useful pins. ·         Extra 3x4 pin holes, next to ICSP connector, which includes Tx, Rx, 5v, 3.3v, ground, SDA and SCL.    ·         All the rest features are kept the same as the official version   Driver installation and usage procedure: · Install   CH340G driver  . ·     Install   Arduino IDE   ß   (click here) ·     Connect the board to computer. ·     Launch Arduino IDE, select board as “arduino uno” ·     Select the com port OS created for the card(control panel   à   device manager) ·     Open basics   à   blink sketch and upload. ·     If you find any difficulty you can contact us, contact details are given below.   Factory Testing Procedure for arduino uno Atmega328p: We will make sure that we have tested the product with following procedure before shipment ·   We have uploaded blink program with 2 second blinking rate of LED ‘L’ instead of 1second default rate. ·   You can check it at the time of receipt of the product. Just connect it to the USB port of any device and the ‘L’ LED will blink at the rate of 2 second.   Package Include arduino uno: ·   1 x   arduino uno development board ·   1 x   USB cable ·   A plastic container box.   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·         In case you find any problem

New Double-Side SMD SOT23-3 to DIP SIP3 Adapter PCB Board DIY Converter Description: The PCB board has two sides. A side and B side it can be used to convert SOT23 (Pin pitch 0.95mm) to SIPmm pin pitch). The PCB board mounting 2.54mm pitch Pin Header, It can be plugged directly into 2.54mm PCB board or breadboard. Package content: 5-pcs DIP Converter PCB Board

New Double-Side SMD SOT23-3 to DIP SIP3 Adapter PCB Board DIY Converter Description: The PCB board has two sides. A side and B side it can be used to convert SOT23 (Pin pitch 0.95mm) to SIPmm pin pitch). The PCB board mounting 2.54mm pitch Pin Header, It can be plugged directly into 2.54mm PCB board or breadboard. Package content: 4-pcs DIP Converter PCB Board

With this board you can develop and prototype with ATMEGA16/ATMEGA pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters.   FEATURES AVR Development Board for Atmel ATMEGA ISP Socket for Flashing On board Regulated Power Supply 5v,12v supplys Easy to test with Burg Connecters wires An RS232 Serial Port 7Seg Mulitplexed Display DC Power Supply Connector(12v Ac or Dc) READY INTERFACE For LCD display 2linex16Character 24Cxx (I2C) (EEPROM) RTC (DS LED array Matrix Key Pad 4 Interrupt Switches +12v Relay (one) Package Content   AVR Development Board (WITH CHIP MAX232) Burg Connecters 20 Nos Female to Female.

SAM3X8EA 32bit ARM Contex-M3 Due R3 Board Control  Arduino Due R3 AT91SAM3X8E   Description The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. Features: 1. Microcontroller ：AT91SAM3X8E   2. Operating Voltage：3.3V  3. Input Voltage (recommended)：7-12V  4. Input Voltage (limits)：6-16V  5. Digital I/O Pins ：54 (of which 12 provide PWM output)  6. Analog Input Pins：12 7. Analog Outputs Pins：2 (DAC) 8. Total DC Output Current on all I/O lines ：130 mA 9. DC Current for 3.3V Pin：800 mA   10. DC Current for 5V Pin：800 mA  11. Flash Memory：512 KB all available for the user applications  12. SRAM：96 KB (two banks: 64KB and 32KB)   13. Clock Speed：84 MHz            Driver installation and usage procedure: ·                      Install  Arduino IDE ß  (click here) no extra driver needed for this card. ·                      Connect the board to computer, OS will auto detect ARDUINO DUE ·                      If the board is not auto detected, go to hardware device manager and choose update driver than choose advanced option “install from specific location” and point to the directory where your Arduino IDE is installed e.g. ”C:/program files/arduino-1.0.2/drivers” ·                      Launch Arduino IDE, select board as “arduino DUE” ·                      Select the com port OS created for the card(control panel  à  device manager) ·                      Open basics  à  blink sketch and upload. Package: 1 MCU BOARD  + 1 USB cable

Arduino Mega R3 compatible board Arduino Clone based on current open source hardware Product Summary: ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz Features: v   Completely solved the traditional board that is not compatible with win7 and win8. v   Increased the pin socket, to facilitate the use of DuPont line cables. v   Replaced Atmega16u2 with CH340G which can easily communicate to Arduino IDE directly.                 Package Include: v   One piece of Arduino Mega board v   One USB cable v   A plastic container box. Shipping Details: Our preferred shipping partners are                             For remote locations we will prefer Indian speed post Feedback v     In case you find any problem

ARDUINO UNO R3 DEVELOPMENT BOARD ATMEGA328P | CH340G | WITH USB CABLE   Package Include: ·         1X ATMEL ATmega328P  CH340G BOARD, USB Cable included   Product description:   Main changes from the older version:  CH340G replace ATmega16U2 AUTO POWER SELECTION FEATURE ENABLED Technical Details: Microcontroller: ATmega328P Operating voltage: 5V  Input Voltage (recommended): 7-12V (EXTERNAL), 5V(USB) Digital I/O Pins: 14 (of which 6 provide PWM output)  Analog Input Pins: 6  DC Current per I/O Pin: 40mA  DC Current for 3.3V pin: 50mA  Flash Memory: 32 KB (ATmega328P) of which 0.5KB used by bootloader  SRAM: 2 KB (ATmega328P)  EEPROM: 1 KB (ATmega328P)  Clock Speed: 16 MHZ  USB Chip CH340G Usage Instructions: Click here for the driver software Before connecting the Board to your USB port: 1.     Download the “ch341ser.exe” file and run it. 2.     The software asks whether it can install the CH341SER.INF driver for the CH340 chip. Click INSTALL 3.     A Windows message asks whether the driver has installed correctly. Click YES. 4.     Connect your Board. 5.     From Control Panel, open Device Manager and Ports. If installed correctly you should see an entry “USB-SERIAL CH340 (COMXX) Install Arduino IDE Download Here http://arduino.cc/en/Main/Software Connect Board to Computer and open Arduino IDE. Select board as "Uno"

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

    Other Items Feedbacks About Us Contact Us Add To Favorites   Set of 5 Pcs AVR28 Base Board  Kit.  For Electronic project.   CNB009 - Development Board For ATmega8,168,328,5 Pc Kit Electronics DIY Projects Atmel AVR - 28 Pin Base Boar d  -  1 Pcs (For ATmega8 ,ATmega 168,ATmega 328 Microcontroller)  **FREE**    10 Wire FRC Cable -  3 Pcs **FREE**    12V 1Amp SMPS -  1 Pc ** Does not Include Any Microcontroller ** ****FREE**** 3 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm.   ,with female connectors on both ends. Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

Micro SD Storage Board adap Micro SD TF Card Memory Shield Module SPI Fr Arduino Description 1 Support Micro SD Card, Micro SDHC card (high-speed card)  2 The level conversion circuit board that can interface level is 5V or 3.3V  3 Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board  4 Communication interface is a standard SPI interface  5 4 M2 screw positioning holes for easy installation  6 Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin;  7 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply  8 Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal  9 Micro SD card connector: yes since the bomb deck for easy card insertion and removal  10 Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination  11 Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is SPI bus, CS is the chip select signal pin  V voltage regulator circuit: LDO regulator output is 3.3V level converter chip, Micro SD card supply  13 Level conversion circuit: Micro SD card into the direction of the signal is converted to 3.3V, MicroSD card interfaces to control the direction of the MISO signal is also converted into 3.3V, general AVR microcontroller system can read the signal;  14 Micro SD card connector: a self- bomb deck, easy card insertion.  15 Positioning holes: 4 M2 screws positioning hole diameter is 2.2mm, the positioning of the module is easy to install, to achieve inter- module combination; Package Info 1Pc X Micro SD Storage Board  Feedback Info We Provide Optimum Quality and Fast Shipping which is self explanatory by Review others have given us please have look if you have any question of doubt. Our Prices are the Cheapest on E-bay, If you find any of our item Selling at cheaper price then Message us the details and we would provide you at same price. For providing such services many individuals and department of ours are working very hard  24hr X 7 X 365 days, and we look for token of appreciation for all this by providing us with positive feedback. For Any Technical Assistance and Guidance Please Post on Our Forum www.sonishop.com/forum We would get back to you for same.

igloon 2 USB 3.0 A Type Female to Female 20 Pin Box Header Slot Adapter Mother Board 20 pin Female to USB 3.0 Female Cable Adapter. igloon 2 USB 3.0 A Type Female to Female 20 Pin Box Header Slot Adapter Mother Board 20 pin Female to USB 3.0 Female Cable Adapter

igloon Blue 2 Port USB 3.0 Type A Male to 20 Pin Header Male Adapter Cable Cord Mother Board 20 pin Male to USB 3.0 Cable Adapter. igloon Blue 2 Port USB 3.0 Type A Male to 20 Pin Header Male Adapter Cable Cord Mother Board 20 pin Male to USB 3.0 Cable Adapter

UNO R3 Development Board ATmega328P ATmega16U2 with USB cable 100% compatible UNO R3 Development Board ATmega328P ATmega16U2 with USB cable 100% compatible 100% compatible Arduino UNO Board The new Uno is the latest version after the Duemilanove, with an improved USB interface chip. Like the Duemilanove, it not only has an expanded shield header with a 3.3V reference and a RESET pin (which solves the problem of how to get to the RESET pin

Product Description: 100% New, RoHS Compliant. This is a Double-Side PCB Circuit Board, Each PCB board has 8 pins, It is compatible with 4 pins 6 pins and 8 pins chips. A side for pin pitch size 1.27mm, It can be used for most of the SO、SOP、SOIC to 2.54mm DIP. B side for pin pitch size 0.65mm, It can be used for most of the SSOP、TSSOP、MSOP to 2.54mm DIP. Package content: 5 -pcs SOP8 SO8 SOIC8 TSSOP8 MSOP8 to DIP8 Converter PCB Board

2 Pcs (One pair) ATMega R3 Compatiable Microcontroller Board with Free USB Cable of Arduino This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality.  100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

Mega R3 Compatiable Microcontroller Board ATmega USB Cable of Arduino This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality.  100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

PRODUCT DETAILS: Arduino UNO R3 Compatible Board ATmega328P ATmega16U2 with USB cable DESCRIPTION This is a Compatible board for Arduino uno r3, not original This UNO is a 100% compatible derivative of current R3 Arduino UNO The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller;simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Features:- Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

4 channel USB Relay Board with 36 Digital/Analog I/Os USB Data Acquisition Board    Welcome to the world of Computer Automation. This USB Relay Board - U96 is a perfect companion for all your computer automation projects. It is USB based card having 4 onboard relays for switching external devices and up to 36 digital & analogue I/Os that will help you to monitor various real world scenarios using switches & different kind of sensors to monitor many parameters like Temperature, Pressure, Light, Touch, PH etc. This card is not only good for controlling Relays but a perfect example for Data Acquisition applications. It appears as a USB CDC (Communications Device Class) device when connected to USB port of a computer. This creates a Virtual Serial (Com) Port, which allows easy communication with the card. Any programming language that supports serial communications (C, C#, C++, VB, VB.NET, Perl, Java etc) can be used to communicate with U96 very easily. Easy to use commands are available to communicate with U96 which handle various tasks like Switching On/Off of Relays, Controlling Digital Inputs & Outputs, Getting analog data etc. The controller provides 4 relay outputs to control various electrical devices. Apart from this, the card has up to 36 digital input & output pins. It has also got 15 Analog input pins. All pins will be individually configured as Digital Input or Digital output or Analog input automatically as per input command. Each Digital pin can support a TTL or Schmitt Trigger Input or a 3.3V output. Each Analog pin will convert analog voltage (Between 0 to 3V) or Higher (through voltage divider) into 12 bit resolution value. The output can be raw data or converted into voltage. The raw data be converted into required form using conversion formulas. Any kind of sensor whether it is providing digital output or analogue output can be interfaced with U96 and monitored with the help of computer. For more information please download U96 User Manual from our download section at http://iknowvations.in/downloads/. If you have any questions, you can contact our support team at support@iknowvations.in

LMTF AMP board KIT+Rectifier filter power KIT + Tone control Kit Introduction:   LM is a single channel high-performance Stereo power amplifier IC produced by National Semiconductor Corporation(NS).The maximum continuous output power is up to 60W.From the Introduction till now,it's widely loved by vast audio fans     This power amplifier adopts power board & amplifier board Independent design,for the amplifier part,each channel shares one circuit board,every set includes one power board & 2 single channel power amplifier boards.  All the components on the board are carefully selected,uF/63V capacitors as filter capacitors,35A large current rectifieer bridge,can ensure the powerboard long-term full load working.Other capacitors choose Epcos, Keltron, etc. famous brand capacitors.1% copper pin film resistors. The PCB board adopts single side circuit board, Black boars,reasonable layout design,looks beautiful & generous. In Package  2 X LM mono boards 1 X Hi Fi Tone control board 1 X uf 63v power supply board 1 X 15v regulated power supply board 

Package Contents   1 x PIC development Board with Free USB cable and CD containing software examples.   External Power supply NOT Included.    Contact Details   Have any Queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"    The PIC development board is a microcontroller board based on the PIC16F877. It has 33 input/output pins and two PWM outputs, 8 (10 bit) analog inputs, a works upto 20 MHz speed. A USB connection is available for programming and UART (communication with the PC), an external power jack is provided for high current motor applications etc. A Reset button is present. A 4 x 4 key matrix is provided for keyscan applications. A 16 x 2 LCD with programmable backlight is provided. A Piezo Buzzer is present. A 4 digit 7 segment common cathode display is populated for display multiplexing example. A onboard potentiometer is provided on one analog channel. A coin cell battery backed DS (RTC) is present on one of the I2C channel. An optional SPI external EEPROM (not provided with the board) can be mounted by the user for SPI memory. A ULN based stepper motor interface is present.   The Board contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. FEATURES AND USAGE The maximum length and width of the Board is approx 7 inch by 5.5 inches. Four PCB studs allow the board to be attached to a surface or act like a support stand. All the ports of the microcontroller are available as edge connectors on the right side of the board on a standard 100 mil spacing. The board can also take most of the 40 Pin DIP PIC18 series microcontrollers. An External programmer may be needed

10 Pcs 2x40 Pin 2.54mm Pitch Double Row PCB Pin Headers. 10 Pcs 2x40 Pin 2.54mm Pitch Double Row PCB Pin Headers Product Name: Pin Header Position: 40 Row: 2 Mounting Angle: Straight Pin Pitch: 2.54mm 0.1 Total Size: 101 x 11 x 5mm 4 x 0.4 x 0.2 (L W H) Material: Plastic Metal Color: Black Gold Tone Net Weight: 44g Package Content: 10 x Pin Headers Features double row straight mounting angle male pin header electronic component. This pin header is an ideal connector for the PCB board and intergrated circuit used widely

This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality. 100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

Multi Interface Board, 10 pin box header to 10pin single line header converter 10 pin single line header to 10pin box header

LMTF AMP board KIT+Rectifier filter power DIY KIT Introduction:   LM is a single channel high-performance Stereo power amplifier IC produced by National Semiconductor Corporation(NS).The maximum continuous output power is up to 60W.From the Introduction till now,it's widely loved by vast audio fans     This power amplifier adopts power board & amplifier board Independent design,for the amplifier part,each channel shares one circuit board,every set includes one power board & 2 single channel power amplifier boards.  All the components on the board are carefully selected,uF/63V capacitors as filter capacitors,35A large current rectifieer bridge,can ensure the powerboard long-term full load working.Other capacitors choose Epcos, Keltron, etc. famous brand capacitors.1% copper pin film resistors. The PCB board adopts single side circuit board, Black boars,reasonable layout design,looks beautiful & generous.