Pins board

SAM3X8EA 32bit ARM Contex-M3 Due R3 Board Control  Arduino Due R3 AT91SAM3X8E   Description The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. Features: 1. Microcontroller ：AT91SAM3X8E   2. Operating Voltage：3.3V  3. Input Voltage (recommended)：7-12V  4. Input Voltage (limits)：6-16V  5. Digital I/O Pins ：54 (of which 12 provide PWM output)  6. Analog Input Pins：12 7. Analog Outputs Pins：2 (DAC) 8. Total DC Output Current on all I/O lines ：130 mA 9. DC Current for 3.3V Pin：800 mA   10. DC Current for 5V Pin：800 mA  11. Flash Memory：512 KB all available for the user applications  12. SRAM：96 KB (two banks: 64KB and 32KB)   13. Clock Speed：84 MHz            Driver installation and usage procedure: ·                      Install  Arduino IDE ß  (click here) no extra driver needed for this card. ·                      Connect the board to computer, OS will auto detect ARDUINO DUE ·                      If the board is not auto detected, go to hardware device manager and choose update driver than choose advanced option “install from specific location” and point to the directory where your Arduino IDE is installed e.g. ”C:/program files/arduino-1.0.2/drivers” ·                      Launch Arduino IDE, select board as “arduino DUE” ·                      Select the com port OS created for the card(control panel  à  device manager) ·                      Open basics  à  blink sketch and upload. Package: 1 MCU BOARD  + 1 USB cable

Product Description: 100% New, RoHS Compliant. This is a Double-Side PCB Circuit Board, Each PCB board has 8 pins, It is compatible with 4 pins 6 pins and 8 pins chips. A side for pin pitch size 1.27mm, It can be used for most of the SO、SOP、SOIC to 2.54mm DIP. B side for pin pitch size 0.65mm, It can be used for most of the SSOP、TSSOP、MSOP to 2.54mm DIP. Package content: 5 -pcs SOP8 SO8 SOIC8 TSSOP8 MSOP8 to DIP8 Converter PCB Board

DESCRIPTION General Brand MatLogix Quantity 1 Color Green Material PCB Features -Zigbee USB Breakout - Easy to connect with PC and Laptops. -On board All Pin Expansion header. -On board LED for RX, TX and Power. Specification Power Supply Input USB Powerd. Interface USB to Serial -on board serial Usb to Serial converter IC Chipset CP Datasheet / Application Discription This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit. This board also breaks out each of the XBee s I/O pins to a pair of breadboard-compatible headers. So if you want to make use of the XBee s extended functionality, you can solder some header pins into those, or even just solder some wire. USB Driver - CP Dimensions & Weight Dimensions Weight 100 g Packing List 1 x Zigbee Explorer Board - USB. 1 x USB A type to B type Cable. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Arduino uno r3 development board with ATmega328p CH340G Arduino clone based on current open source hardware Arduino uno Atmega 328p smd ideal for prototyping Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.   Product Summary arduino uno: ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz         Features of arduino uno: ·         Replaced the expensive 16u2 with CH340G chip to avoid the driver compatibility problem which was found on some win7/win8 OSes. ·         Increased the extra pin holes to facilitate the use of DuPont line cables, with some extra useful pins. ·         Extra 3x4 pin holes, next to ICSP connector, which includes Tx, Rx, 5v, 3.3v, ground, SDA and SCL.    ·         All the rest features are kept the same as the official version   Driver installation and usage procedure: · Install   CH340G driver  . ·     Install   Arduino IDE   ß   (click here) ·     Connect the board to computer. ·     Launch Arduino IDE, select board as “arduino uno” ·     Select the com port OS created for the card(control panel   à   device manager) ·     Open basics   à   blink sketch and upload. ·     If you find any difficulty you can contact us, contact details are given below.   Factory Testing Procedure for arduino uno Atmega328p: We will make sure that we have tested the product with following procedure before shipment ·   We have uploaded blink program with 2 second blinking rate of LED ‘L’ instead of 1second default rate. ·   You can check it at the time of receipt of the product. Just connect it to the USB port of any device and the ‘L’ LED will blink at the rate of 2 second.   Package Include arduino uno: ·   1 x   arduino uno development board ·   1 x   USB cable ·   A plastic container box.   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·         In case you find any problem

Description: 100% brand new and high quality The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much. The Digispark is shipped fully assembled except for the two included and easy to solder headers. Here are the specs: Support for the Arduino IDE 1.0+ (OSX/Win/Linux) Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection)On-board 500ma 5V Regulator Built-in USB6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB) 8k Flash Memory (about 6k after bootloader) I2C and SPI (vis USI)PWM on 3 pins (more possible with Software PWM) ADC on 4 pins Power LED and Test/Status LED Size:2x1.7cm(approx) Package Included: 1 x Digispark Kickstarter Attiny85 USB Development Board for Arduino Full Wiki link:  digispark Wiki         Software: NOTE:  If you used a version of the ide where the digistump add-ons were installed separately you must delete the digistump folder at My Documents/Arduino/hardware (windows) or Documents/Arduino/hardware (OS  X) or /home/[username]/Sketchbook (Linux) or this new IDE install will not work properly and you will get library errors! The Digispark uses the Arduino IDE - Digistump Release 1.5.x which is the Arduino IDE with some custom additions and supports Digispark, Digispark Pro, and DigiX. These are presented as a fully integrated package with 1.5.x that can be downloaded as an installed or zip file. First download the appropriate package: Windows (now with fully signed drivers!) Installer (recommended): https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpArduinoInstall1.5.8C.exe Zip:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8C.zip Mac:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8COSX.zip Linux: 32-bit:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8C-linux32.tar.gz 64-bit:  https://github.com/digistump/DigistumpArduino/releases/download/v1.5.8C/DigistumpIDE1.5.8C-linux64.tar.gz Note: report any issues with the builds to the forum:  http://digistump.com/board Compiling from source:  https://github.com/digistump/DigistumpArduino Windows Install Complete these steps before plugging

PRODUCT DETAILS: Arduino UNO R3 Compatible Board ATmega328P ATmega16U2 with USB cable DESCRIPTION This is a Compatible board for Arduino uno r3, not original This UNO is a 100% compatible derivative of current R3 Arduino UNO The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller;simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Features:- Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

4 channel USB Relay Board with 36 Digital/Analog I/Os USB Data Acquisition Board    Welcome to the world of Computer Automation. This USB Relay Board - U96 is a perfect companion for all your computer automation projects. It is USB based card having 4 onboard relays for switching external devices and up to 36 digital & analogue I/Os that will help you to monitor various real world scenarios using switches & different kind of sensors to monitor many parameters like Temperature, Pressure, Light, Touch, PH etc. This card is not only good for controlling Relays but a perfect example for Data Acquisition applications. It appears as a USB CDC (Communications Device Class) device when connected to USB port of a computer. This creates a Virtual Serial (Com) Port, which allows easy communication with the card. Any programming language that supports serial communications (C, C#, C++, VB, VB.NET, Perl, Java etc) can be used to communicate with U96 very easily. Easy to use commands are available to communicate with U96 which handle various tasks like Switching On/Off of Relays, Controlling Digital Inputs & Outputs, Getting analog data etc. The controller provides 4 relay outputs to control various electrical devices. Apart from this, the card has up to 36 digital input & output pins. It has also got 15 Analog input pins. All pins will be individually configured as Digital Input or Digital output or Analog input automatically as per input command. Each Digital pin can support a TTL or Schmitt Trigger Input or a 3.3V output. Each Analog pin will convert analog voltage (Between 0 to 3V) or Higher (through voltage divider) into 12 bit resolution value. The output can be raw data or converted into voltage. The raw data be converted into required form using conversion formulas. Any kind of sensor whether it is providing digital output or analogue output can be interfaced with U96 and monitored with the help of computer. For more information please download U96 User Manual from our download section at http://iknowvations.in/downloads/. If you have any questions, you can contact our support team at support@iknowvations.in

From Printer Type(Type B) USB connector to micro USB connector Replace the expensive FTDI FT232RL IC to CH340 IC. Replace the main IC atmega 328 PTH to atmega SMD QFP with arduino uno bootloader. Reserved extra male pins holes, so both female and male pins available on board, with some extra useful pins. Reserved another 2×4 pin holes, next to ISCP, pins includes: TX, RX, VCC, GND, IIC-SCL, IIC-SDA, power pins All the rest features are kept the same as the official version.   First Download the CH340 Driver from http://wch.cn/downfile/195 or http://kiguino.moos.io/downloads/CH341SER_MAC.ZIP or https://www.dropbox.com/s/o2a5vntk7n5y7hi/CH341SER.zip?dl=0

ARDUINO UNO R3 DEVELOPMENT BOARD ATMEGA328P | CH340G | WITH USB CABLE   Package Include: ·         1X ATMEL ATmega328P  CH340G BOARD, USB Cable included   Product description:   Main changes from the older version:  CH340G replace ATmega16U2 AUTO POWER SELECTION FEATURE ENABLED Technical Details: Microcontroller: ATmega328P Operating voltage: 5V  Input Voltage (recommended): 7-12V (EXTERNAL), 5V(USB) Digital I/O Pins: 14 (of which 6 provide PWM output)  Analog Input Pins: 6  DC Current per I/O Pin: 40mA  DC Current for 3.3V pin: 50mA  Flash Memory: 32 KB (ATmega328P) of which 0.5KB used by bootloader  SRAM: 2 KB (ATmega328P)  EEPROM: 1 KB (ATmega328P)  Clock Speed: 16 MHZ  USB Chip CH340G Usage Instructions: Click here for the driver software Before connecting the Board to your USB port: 1.     Download the “ch341ser.exe” file and run it. 2.     The software asks whether it can install the CH341SER.INF driver for the CH340 chip. Click INSTALL 3.     A Windows message asks whether the driver has installed correctly. Click YES. 4.     Connect your Board. 5.     From Control Panel, open Device Manager and Ports. If installed correctly you should see an entry “USB-SERIAL CH340 (COMXX) Install Arduino IDE Download Here http://arduino.cc/en/Main/Software Connect Board to Computer and open Arduino IDE. Select board as "Uno"

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Features: l           Support for the IDE 1.0+ (OSX/Win/Linux) l           Power via USB or External Source l           On-board 500ma 5V Regulator l           Built-in USB(and serial debugging) l           6 I/O Pins (2 are used for USB only if your program actively communicates over USB otherwise you can use all 6 even if you are programming via USB) l           8k Flash Memory (about 6K after bootloader) l           I2C and SPI(vis USI) l           PWM on 3 pins (more possible with Software PWM l           ADC on 4 pins l           Power LED and Test/ Status LED (on Pin0) 　 Package includes: l        1x Digispark Miniature USB Development Board l        1x 3-Pin connector l        1x 6-Pin connector Note: As the package is very big and the shipping fee would be very high, we will ship the item out without its original box. Anyhow, the shipping is very safe. Also available                                 Digispark Kickstarter USB Development Board for Arduino Tiny 85 (USB Male A Interface) Important  Note:  Please check your shipping address during checkout. powership policies do not allow change of address after payment. You have order the item again to change the shipping address. Now Fast shipping with  powerShip  through  Blue Dart / DTDC / Aramex / FedEx. 

Features: l           Support for the IDE 1.0+ (OSX/Win/Linux) l           Power via USB or External Source l           On-board 500ma 5V Regulator l           Built-in USB(and serial debugging) l           6 I/O Pins (2 are used for USB only if your program actively communicates over USB otherwise you can use all 6 even if you are programming via USB) l           8k Flash Memory (about 6K after bootloader) l           I2C and SPI(vis USI) l           PWM on 3 pins (more possible with Software PWM l           ADC on 4 pins l           Power LED and Test/ Status LED (on Pin0) 　 Package includes: l        1x Digispark Miniature USB Development Board l        1x 3-Pin connector l        1x 6-Pin connector Note: As the package is very big and the shipping fee would be very high, we will ship the item out without its original box. Anyhow, the shipping is very safe. Also available                                 Digispark Kickstarter USB Development Board for Arduino Tiny 85 (micro-USB Female Interface) Important  Note:  Please check your shipping address during checkout. powership policies do not allow change of address after payment. You have order the item again to change the shipping address. Now Fast shipping with  powerShip  through  Blue Dart / DTDC / Aramex / FedEx. 

USB Micro B Connector Board Description Micro USB Interface Board Power Switch Interface provides the best and convenient way to add USB port to your project with hassle free mounting on and standard PCB board. The breakout board provides a Micro-B USB connector's VCC, GND, ID, D- and D+ pins on a 0.1" pitch header. Features Brand new, High quality and Fast Shipping Color: Blue Size: 150mm x 200mm Pins: VCC, GND, ID, D- and D+ Ideal for an un-regulated 5V supply up to 100mA for any project. Assembled and Tested Protected with ESD pouch Package Includes 1 x USB Micro B Female Breakout Board 1 x 5 pin 0.1 pitch mounting header Shipment All India Free Shipping. We use reliable shipping partners such as BlueDart, DHL, Professional Couriers, DTDC, Aramex etc. The product will be shipped on the same day if the payment has been cleared before 2:00 P.M on weekdays. Next day shipping on Weekends. On receipt of the product, kindly acknowledge the same immediately on Feedback We strive to win 5 star feedback from our esteemed customers. If you are un-satified with the product, please talk to us (contact.saidaikar@gmail.com) before leaving negative feedback. Your feedback is very very important for us to grow our business on , so please do leave feedback. Thank you for your buisness

Micro SD Storage Board adap Micro SD TF Card Memory Shield Module SPI Fr Arduino Description 1 Support Micro SD Card, Micro SDHC card (high-speed card)  2 The level conversion circuit board that can interface level is 5V or 3.3V  3 Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board  4 Communication interface is a standard SPI interface  5 4 M2 screw positioning holes for easy installation  6 Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin;  7 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply  8 Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal  9 Micro SD card connector: yes since the bomb deck for easy card insertion and removal  10 Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination  11 Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is SPI bus, CS is the chip select signal pin  V voltage regulator circuit: LDO regulator output is 3.3V level converter chip, Micro SD card supply  13 Level conversion circuit: Micro SD card into the direction of the signal is converted to 3.3V, MicroSD card interfaces to control the direction of the MISO signal is also converted into 3.3V, general AVR microcontroller system can read the signal;  14 Micro SD card connector: a self- bomb deck, easy card insertion.  15 Positioning holes: 4 M2 screws positioning hole diameter is 2.2mm, the positioning of the module is easy to install, to achieve inter- module combination; Package Info 1Pc X Micro SD Storage Board  Feedback Info We Provide Optimum Quality and Fast Shipping which is self explanatory by Review others have given us please have look if you have any question of doubt. Our Prices are the Cheapest on E-bay, If you find any of our item Selling at cheaper price then Message us the details and we would provide you at same price. For providing such services many individuals and department of ours are working very hard  24hr X 7 X 365 days, and we look for token of appreciation for all this by providing us with positive feedback. For Any Technical Assistance and Guidance Please Post on Our Forum www.sonishop.com/forum We would get back to you for same.

LilyPad 328 ATmega328P Main Board compatible with Arduino’s IDE Features: Brand new and high quality The LilyPad Iduino is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The LilyPad Iduino can be programmed with the software. The ATmega328V on the LilyPad comes preburned with a bootloader that allows you to upload new code to it with the software. You can also bypass the bootloader and program the ATmega through the ICSP (In-Circuit Serial Programming) header. The LilyPad should only be programmed with software versions 0010 or higher. You can program it with earlier versions, but all of the time related functions will be switched off (making them twice as slow as they should be). Warning: Do not power the LilyPad with more than 5.5 volts, or plug the power in backwards: you'll kill it. 328 Main board; The Digital I/O Digital input/output terminal, a total of 0 ~ 13; The Analog I/O Analog input/output terminal, a total of 0 ~ 5; Support the ISP download function; Support the TX/RX terminals; Support the AREF terminals; Support the six groups of PWM terminal (Pin11 Pin10, Pin9, Pin6 and Pin5, responsible); The input voltage: 3.3 V DC; Using Atmel Atmega328V - 20 pu microcontroller; Specifications: Microcontroller: ATmega328V Operating Voltage: 2.7-5.5 V Input Voltage: 2.7-5.5 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 6 DC Current per I/O Pin: 40 mA Flash Memory: 16 KB (of which 2 KB used by bootloader) SRAM: 1 KB EEPROM: 512 bytes Clock Speed: 8 MHz Package includes: 1* LilyPad atmega 328 Main board Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Arduino Mega R3 compatible board Arduino Clone based on current open source hardware Product Summary: ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz Features: v   Completely solved the traditional board that is not compatible with win7 and win8. v   Increased the pin socket, to facilitate the use of DuPont line cables. v   Replaced Atmega16u2 with CH340G which can easily communicate to Arduino IDE directly.                 Package Include: v   One piece of Arduino Mega board v   One USB cable v   A plastic container box. Shipping Details: Our preferred shipping partners are                             For remote locations we will prefer Indian speed post Feedback v     In case you find any problem

2 Pcs (One pair) ATMega R3 Compatiable Microcontroller Board with Free USB Cable of Arduino This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality.  100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

Mega R3 Compatiable Microcontroller Board ATmega USB Cable of Arduino This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality.  100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

Product Description ARM Core benefits The Due has a 32-bit ARM core that can outperform typical 8-bit microcontroller boards. The most significant differences are: A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. (for more information look  int type  page). CPU Clock at 84Mhz. 96 KBytes of SRAM. 512 KBytes of Flash memory for code. a DMA controller, that can relieve the CPU from doing memory intensive tasks. Product includes 1x arduino board 1x USB cable Summary Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Outputs Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Powered by Turbo Lister

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328)

Package Contains 1XArduino Uno R3 1X Usb Cable for Arduino The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

Description: The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Summary Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

This MEGA is a 100% compatible derivative of current R3 Arduino Mega Note: This is Clone Board Mega AU (16 Mhz) R3 Board Highest Quality. 100% Arduino-Compatible. Product Technical Specification Microcontroller ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz

Package Contents   1 x PIC development Board with Free USB cable and CD containing software examples.   External Power supply NOT Included.    Contact Details   Have any Queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"    The PIC development board is a microcontroller board based on the PIC16F877. It has 33 input/output pins and two PWM outputs, 8 (10 bit) analog inputs, a works upto 20 MHz speed. A USB connection is available for programming and UART (communication with the PC), an external power jack is provided for high current motor applications etc. A Reset button is present. A 4 x 4 key matrix is provided for keyscan applications. A 16 x 2 LCD with programmable backlight is provided. A Piezo Buzzer is present. A 4 digit 7 segment common cathode display is populated for display multiplexing example. A onboard potentiometer is provided on one analog channel. A coin cell battery backed DS (RTC) is present on one of the I2C channel. An optional SPI external EEPROM (not provided with the board) can be mounted by the user for SPI memory. A ULN based stepper motor interface is present.   The Board contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. FEATURES AND USAGE The maximum length and width of the Board is approx 7 inch by 5.5 inches. Four PCB studs allow the board to be attached to a surface or act like a support stand. All the ports of the microcontroller are available as edge connectors on the right side of the board on a standard 100 mil spacing. The board can also take most of the 40 Pin DIP PIC18 series microcontrollers. An External programmer may be needed

Description Single Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has ONE relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a Single channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description Four Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has FOUR relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a 4 channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

AROBOTSHOP  ARDUINO UNO R3 Original Development Board with USB Cable Features:- Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Contact us: Arobot www.arobot.in Phone: Mobile: Email to us: 

The Arduino Uno is a micro controller board based on the ATmega328. Summary Micro controller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

Arduino Mega R3 compatible board BEST QUALITY AMONGST ALL OTHER ARDUINO CLONES AVAILABLE Arduino Clone based on current open source hardware   Product Description: ATmega Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 15 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16  MHz