Relay module pic

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc....   ***(Work with All Analog/Digital circuits with signal from 3V to 15V) *** Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 3.3v and 5v micro controller  (Check Other Listings  for  1.8V-5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 3V to 16V(1.5V to 16V for 1.8V logic) with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 3.3V and 5V micro controllers/Digital (1.8V Version also available Please Check My other Listings).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

1 Channel Isolated 5V Relay Module Coupling For Arduino PIC AVR DSP ARM   the module is compliant with international safety standards, control and load areas isolation trenches; a single relay a genuine; power supply and relay instructions, lit, disconnect is off; input signal, signal, common Terminal and start conducting; can be used as a single chip modules can be used for appliance control; DC or AC signal, control, you can control the 220V AC load; there is a normally open and one normally closed contact; Specification: One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for avoidance of malfunction Power supply indicator lamp Control indicator lamp Channel: 1 channel Relay Voltage: 5V Note  on the high level and low level triggered mode, friends who do not understand, have a look: High level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way; Low level trigger refers to the signal voltage between input terminal and Earth OV trigger, can be understood as signal input terminal and the GND negative electrode short circuit triggered a way  1-channel relay module connection Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

1 Channel Isolated 5V Relay Module Coupling For Arduino PIC AVR DSP ARM   the module is compliant with international safety standards, control and load areas isolation trenches; a single relay a genuine; power supply and relay instructions, lit, disconnect is off; input signal, signal, common Terminal and start conducting; can be used as a single chip modules can be used for appliance control; DC or AC signal, control, you can control the 220V AC load; there is a normally open and one normally closed contact; Specification: One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for avoidance of malfunction Power supply indicator lamp Control indicator lamp Channel: 1 channel Relay Voltage: 5V Note  on the high level and low level triggered mode,  High level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way; Low level trigger refers to the signal voltage between input terminal and Earth OV trigger, can be understood as signal input terminal and the GND negative electrode short circuit triggered a way  1-channel relay module connection SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you

5V 4--Channel Relay Module for Arduino PIC ARM DSP AVR Electronic NEW Product Description 1. module with pine le relay control, ac voltage maximum 250 V, ac current maximum 10 A, dc voltage maximum 30 V, dc current maximum 10 A;  2. the transistor drive, drive ability;  3. working voltage 5 V  4. has the fixed bolt hole and easy installation  5. small board PCB size: 7.2 cm * 4.8 cm  6. weight ：60 g Package included: 1 PCS Rs. 410 Shipping is all over India. Please Provide Complete Address and phone number. See Shipping description for details Shipment will be sent between 3.00 pm to 4.00 pm except Sundays/Public Holidays.  Tracking details will be provided within 12hours after shipment is booked. Most shipments will be sent through Speed Post/Registered Post

Description Package Includes: 1 Piece new  5V 2 Two Channel Relay Module With optocoupler for Arduino PIC ARM DSP AVR It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description Package Includes: 1 Piece new 12V  Two Channel Relay Module With optocoupler for Arduino PIC ARM DSP AVR It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

  Description Package Includes: 1 Piece new 12V  Two Channel Relay Module With optocoupler for Arduino PIC ARM DSP AVR It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Product Description: ·          5V 4-Channel Relay interface board ·          IC based  switching ·           Supply 12V DC and 5 V DC for control. ·           High power relays for each channel: 250V 10A AC ·           Indication LED for each output  Standard interface that can be controlled directly by micro controller (Arduino, , AVR, PIC, DSP, ARM)   Application: Application for automation  purpose Package contain: 1 X 4-Channel Relay interface   = MM_contentVersion; } else if (navigator.userAgent && navigator.userAgent.indexOf("MSIE")>=0 && (navigator.appVersion.indexOf("Win") != -1)) { document.write(' /n'); document.write('on error resume next/n'); document.write('MM_FlashCanPlay = (IsObject(CreateObject("ShockwaveFlash.ShockwaveFlash." & MM_contentVersion)))/n /n'); } if (MM_FlashCanPlay) { document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); } else { document.write(' '); document.write(' '); document.write(' The Buyer Appreciation banner is best viewed with Macromedia Flash Player 6 or higher. '); document.write(' Click here to get the latest Macromedia Flash Player. '); document.write(' '); document.write('

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers,  such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc.... ***(Work with All Analog/Digital circuits with signal from 1.5V to 15V) ***   Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 1.8V,3.3v and 5v micro controller  (Check Other Listings  for  3.3V,5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 1.5V to 16V with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 1.8V, 3.3V and 5V micro controllers/Digital).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

Description: Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two Two on-board relay which can switch up to 7Amps. Relays terminals (COM, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free-wheeling diode which will further protect your microcontroller from relay kick back. This is a 5V 2-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.    Features: 1.     Equipped with high-current relay 7A@250VAC / 10A@24VDC.  2.     It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. 3.     High quality screw terminals (Terminal Block) provided (COM, NC, NO) for quick and easy connection. 4.     Free wheeling diode to protect your microcontroller. 5.     Input Signal Pin connected to Burg stick for easy accessibility. 6.     LED Status indicators to indicate the relay ON/OFF status. 7.     Mounting holes provided. Package Contains: 1.      1 x Two channel 5V relay Module.    

Features: Brand new and high quality. This module can be used with Special Sensor Shield V4.0. You can do some simple design about it. This is 2-Channel 5V Relay Module for PIC ARM AVR DSP. It can be able to control various appliances, and other equipments with large current. Easy to be controlled by a lots of Microcontrollers. Just use 5v input signal to control. Equiped with high-current relay, AC250V 10A, AC150V 10A; DC30V 10A, DC28V 10A. size:3.9cm x 5.1cm (1.54inch x 2.01inch).   Package contents: 1 x   5V 10A   2-Ch  Relay Board Module FEED BACK We request buyers to leave all star feedback if satisfied and if not satisfied they can communicate and contact us so we can take appropriate action.     Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback      Your feedback is important for us to grow our business on , so please do leave feedback

Isolated Optocoupler Driver Power Relay Module 8CH 5V for AVR 51 PIC SCM  FREE SHIPPING Product Name Optocoupler Driver Relay Module Relay Type SRD-05VDC-SL-C Coil Voltage DC 5V Pole Number 8 Channel Load 10A, AC 250V/125V, DC 30V/28V Overall Size 13.8 x 5.5 x 1.8cm/5.4" x 2.2" x 0.7"(L*W*H) Materials Metal, Plastic, Electric Parts Main Color Blue

1 Channel Relay Board Module For PIC AVR DSP ARM Arduino AVRDuino This is a  1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino, AVRDuino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).   Features: 1 -Channel Relay interface board Equiped with high-current relay, Rating are as follows: 1) 7A-250 V AC 2) 10A-125V AC 3) 12A 120V DC 4) 10A 28V DC Standard interface that can be controlled directly by microcontroller (Arduino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)   Has the fixed bolt hole and easy installation Small board PCB size R elay status indicator LED (red) Weight ： 10 0 g   Module interface specifications (3 wire)   1. External 12V 2. GND external GND 3. 1N interchange relay control interface (Control by 3.3V or 5V Logic)   Package included:   1 Channel Relay Board Module Note: Relay and Component Colors varies as per availability.

This is a  4-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino, AVRDuino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features: 4-Channel Relay interface board Equiped with high-current relay, Rating are as follows: 1) 7A-250v AC 2) 10A-125V AC 3) 12A 120V DC 4) 10A 28V DC Standard interface that can be controlled directly by microcontroller (Arduino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)   Has the fixed bolt hole and easy installation Small board PCB size four ways of relay status indicator LED (red) Weight ： 15 0 g Module interface specifications (6 wire) 1. External 12V 2. GND external GND Package included: 10 x  4 Channel Relay Board Module Note: Relay and Component Colors varies as per availability.

This is a  4-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino, AVRDuino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features: 4-Channel Relay interface board Equiped with high-current relay, Rating are as follows: 1) 7A-250v AC 2) 10A-125V AC 3) 12A 120V DC 4) 10A 28V DC Standard interface that can be controlled directly by microcontroller (Arduino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)   Has the fixed bolt hole and easy installation Small board PCB size four ways of relay status indicator LED (red) Weight ： 15 0 g Module interface specifications (6 wire) 1. External 12V 2. GND external GND Package included: 1 x  4 Channel Relay Board Module Note: Relay and Component Colors varies as per availability.

Package Contents 1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has one (1) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free wheeling diode which will further protect your microcontroller from relay kick back. This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Free wheeling diode to protect your microcontroller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four (4) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has 2 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two (2) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and Transistor will further protect your micro-controller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - BC 547 Transistor used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided