5v relay module optocoupler

1 Channel Isolated 5V Relay Module Coupling For Arduino PIC AVR DSP ARM   the module is compliant with international safety standards, control and load areas isolation trenches; a single relay a genuine; power supply and relay instructions, lit, disconnect is off; input signal, signal, common Terminal and start conducting; can be used as a single chip modules can be used for appliance control; DC or AC signal, control, you can control the 220V AC load; there is a normally open and one normally closed contact; Specification: One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for avoidance of malfunction Power supply indicator lamp Control indicator lamp Channel: 1 channel Relay Voltage: 5V Note  on the high level and low level triggered mode, friends who do not understand, have a look: High level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way; Low level trigger refers to the signal voltage between input terminal and Earth OV trigger, can be understood as signal input terminal and the GND negative electrode short circuit triggered a way  1-channel relay module connection Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

1 Channel Isolated 5V Relay Module Coupling For Arduino PIC AVR DSP ARM   the module is compliant with international safety standards, control and load areas isolation trenches; a single relay a genuine; power supply and relay instructions, lit, disconnect is off; input signal, signal, common Terminal and start conducting; can be used as a single chip modules can be used for appliance control; DC or AC signal, control, you can control the 220V AC load; there is a normally open and one normally closed contact; Specification: One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for avoidance of malfunction Power supply indicator lamp Control indicator lamp Channel: 1 channel Relay Voltage: 5V Note  on the high level and low level triggered mode,  High level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way; Low level trigger refers to the signal voltage between input terminal and Earth OV trigger, can be understood as signal input terminal and the GND negative electrode short circuit triggered a way  1-channel relay module connection SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you

5V 2 Channel Relay with Optocoupler Description This is a 2-Channel Relay interface board, which can control various appliances, and other equipments. It can be controlled directly by Microcontroller.   Rated voltage: DC12   Rated current: 10A   Coil power: 0.36W  Contact switch voltage: 220VAC  Protective characteristics: Sealed   Contact load: Medium-power  Application: Electromagnetism  Contact Form: Conversion type With 4 mounting holes, diameter of each hole is 3.1mm, easy to install  Apply superior SONGLE relay, SPDT(single-pole double-throw), one common port, one NO and one NC  Opto-isolator, excellent anti-interference performance Low level actuation(indicator ON), high level release(indicator OFF) Maximum output of relay: DC 30 Package Info 1Pc X 5V 2 Channel Relay with Optocoupler Feedback Info We Provide Optimum Quality and Fast Shipping which is self explanatory by Review please have a look. Our Prices are the Cheapest on E-bay, If you find any of our item Selling at cheaper price then Message us the details and we would provide you at same price. For providing such services many individuals and department of ours are working very hard 24hr X 7 X 365 days, and we look for token of appreciation for all this by providing us with positive feedback. = MM_contentVersion; } else if (navigator.userAgent && navigator.userAgent.indexOf("MSIE")>=0 && (navigator.appVersion.indexOf("Win") != -1)) { document.write(' /n'); document.write('on error resume next/n'); document.write('MM_FlashCanPlay = (IsObject(CreateObject("ShockwaveFlash.ShockwaveFlash." & MM_contentVersion)))/n /n'); } if (MM_FlashCanPlay) { document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); } else { document.write(' '); document.write(' '); document.write(' The Buyer Appreciation banner is best viewed with Macromedia Flash Player 6 or higher. '); document.write(' Click here to get the latest Macromedia Flash Player. '); document.write(' '); document.write('

5V 4--Channel Relay Module for Arduino PIC ARM DSP AVR Electronic NEW Product Description 1. module with pine le relay control, ac voltage maximum 250 V, ac current maximum 10 A, dc voltage maximum 30 V, dc current maximum 10 A;  2. the transistor drive, drive ability;  3. working voltage 5 V  4. has the fixed bolt hole and easy installation  5. small board PCB size: 7.2 cm * 4.8 cm  6. weight ：60 g Package included: 1 PCS Rs. 410 Shipping is all over India. Please Provide Complete Address and phone number. See Shipping description for details Shipment will be sent between 3.00 pm to 4.00 pm except Sundays/Public Holidays.  Tracking details will be provided within 12hours after shipment is booked. Most shipments will be sent through Speed Post/Registered Post

Description Package Includes: 1 Piece new  5V 2 Two Channel Relay Module With optocoupler for Arduino PIC ARM DSP AVR It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc....   ***(Work with All Analog/Digital circuits with signal from 3V to 15V) *** Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 3.3v and 5v micro controller  (Check Other Listings  for  1.8V-5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 3V to 16V(1.5V to 16V for 1.8V logic) with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 3.3V and 5V micro controllers/Digital (1.8V Version also available Please Check My other Listings).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

Description: Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two Two on-board relay which can switch up to 7Amps. Relays terminals (COM, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free-wheeling diode which will further protect your microcontroller from relay kick back. This is a 5V 2-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.    Features: 1.     Equipped with high-current relay 7A@250VAC / 10A@24VDC.  2.     It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. 3.     High quality screw terminals (Terminal Block) provided (COM, NC, NO) for quick and easy connection. 4.     Free wheeling diode to protect your microcontroller. 5.     Input Signal Pin connected to Burg stick for easy accessibility. 6.     LED Status indicators to indicate the relay ON/OFF status. 7.     Mounting holes provided. Package Contains: 1.      1 x Two channel 5V relay Module.    

4-channel relay control board module with optocoupler, 4 way relay module for arduino 4-channel relay output modules, relay output contacts 250A 10A. Input IN1, IN2, IN3, IN4, the signal line LOW effective. VCC, GND power input, can relay a separate power supply relay power input of JD-VCC. Uses: support all MCU control. the industrial sector PLC control smart home control Module parameters: Size: 75mm (length) x 55mm (W) x 19.3mm (height); Weight: 58g; PCB Color: Blue; board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed; Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal; optocoupler isolation, good anti-jamming; Low pull, high release. Energisation status indicator light, release status LED is off; VCC for the system power, JD_VCC for the relay power. Default hair 5V relay, plug the jumper cap to; Relay Maximum output: DC 30V/10A, AC 250V/10A Wiring: VCC: positive power supply system GND: System power supply negative IN1 – IN4: relay control ports Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

12V 30A C Type EL817 Optocoupler isolated relay module Description: 1    EL817 optocouplers 2、12V,30A/250VAC,30A/30VDC relay 3、can be directly connected with I/0 with MCU 4、diode freewheeling protection 5、(NO)，(NC) 6、PCB size：34(mm)x39(mm). Package Content: 1pc 12V 30A C Type EL817 Optocoupler isolated relay module SHIPPING ·         Product will be shipped on same day if the order is before 1pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 1pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you    

Description Package Includes: 1 Piece new 12V  Two Channel Relay Module With optocoupler for Arduino PIC ARM DSP AVR It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

  Description Package Includes: 1 Piece new 12V  Two Channel Relay Module With optocoupler for Arduino PIC ARM DSP AVR It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description Package Includes: 1 Piece new  8 Road/Channel Relay Module (with light coupling) 5V 12V 24V It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

  Description Package Includes: 1 Piece new  8 Road/Channel Relay Module (with light coupling) 5V 12V 24V It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

  Description Package Includes: 1 Piece new  8 Road/Channel Relay Module (with light coupling) 5V  It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Features: Brand new and high quality. This module can be used with Special Sensor Shield V4.0. You can do some simple design about it. This is 2-Channel 5V Relay Module for PIC ARM AVR DSP. It can be able to control various appliances, and other equipments with large current. Easy to be controlled by a lots of Microcontrollers. Just use 5v input signal to control. Equiped with high-current relay, AC250V 10A, AC150V 10A; DC30V 10A, DC28V 10A. size:3.9cm x 5.1cm (1.54inch x 2.01inch).   Package contents: 1 x   5V 10A   2-Ch  Relay Board Module FEED BACK We request buyers to leave all star feedback if satisfied and if not satisfied they can communicate and contact us so we can take appropriate action.     Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback      Your feedback is important for us to grow our business on , so please do leave feedback