Atmel pin

Atmel ATMEGA328P Microcontroller with Arduino UNO Bootloader You Will Get:ATMEGA328P with Arduino UNO Boot-loader = 1 Features: • High-performance, Low-power Atmel®AVR® 8-bit Microcontroller • Advanced RISC Architecture – 130 Powerful Instructions – Most Single-clock Cycle Execution – 32 × 8 General Purpose Working Registers – Fully Static Operation – Up to 16MIPS Throughput at 16MHz – On-chip 2-cycle Multiplier • High Endurance Non-volatile Memory segments – 32Kbytes of In-System Self-programmable Flash program memory – 512Bytes EEPROM – 1Kbyte Internal SRAM – Write/Erase Cycles: Flash/ EEPROM – Data retention: 20 years at 85°C/100 years at 25°C(1) – Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation – Programming Lock for Software Security • Peripheral Features – Two 8-bit Timer/Counters with Separate Prescaler, one Compare Mode – One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode – Real Time Counter with Separate Oscillator – Three PWM Channels – 8-channel ADC

Atmel ATMEGA8L - IC - 8PU 28-Pin 8MHz 8kb 8-bit Micro controller With 28 Pin Base 28-pin AVR Microcontroller Flash Program Memory: 8 kbytes EEPROM Data Memory: 512 bytes SRAM Data Memory: 1 kbytes I/O Pins: 23 Timers: Two 8-bit / One 16-bit A/D Converter: 10-bit Six Channel PWM: Three Channels RTC: Yes with Separate Oscillator MSSP: SPI and I²C Master and Slave Support USART: Yes External Oscillator: up to 8MHz About us Elemesh Tech Solutions Pvt. Ltd. is an Indian leading electronics, electrical, semiconductors & industrial supplier, currently having Sales & Service branches

    Other Items Feedbacks About Us Contact Us Add To Favorites   Set of 5 Pcs AVR28 Base Board  Kit.  For Electronic project.   CNB009 - Development Board For ATmega8,168,328,5 Pc Kit Electronics DIY Projects Atmel AVR - 28 Pin Base Boar d  -  1 Pcs (For ATmega8 ,ATmega 168,ATmega 328 Microcontroller)  **FREE**    10 Wire FRC Cable -  3 Pcs **FREE**    12V 1Amp SMPS -  1 Pc ** Does not Include Any Microcontroller ** ****FREE**** 3 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm.   ,with female connectors on both ends. Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: 0755-2420735, +91-9039873050 (10:30AM-6:30PM, Monday-Saturday) email: chipsnboards@gmail.com .in Toll free Helpline: 1800 209 3229 FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

The Atmel  8-bit   AVR   RISC -based microcontroller combines 32 KB  ISP   flash  memory with read-while-write capabilities, 1 KB  EEPROM, 2 KB  SRAM, 23 general purpose I/O lines, 32 general purpose working  registers, three flexible timer/ counters  with compare modes, internal and external  interrupts, serial programmable  USART, a byte-oriented 2-wire serial interface,  SPI  serial port, 6-channel 10-bit  A/D converter  (8-channels in  TQFP  and  QFN / MLF  packages), programmable  watchdog timer  with internal  oscillator, and five software selectable power saving modes. The device operates between volts. The device achieves throughputs approaching 1  MIPS  per MHz. Key parameters [edit] PARAMETERS VALUE Flash 32 Kbytes RAM 2 Kbytes Pin Count 28 Max. Operating Frequency 20 MHz CPU 8-bit AVR # of Touch Channels 16 Hardware QTouch Acquisition No Max I/O Pins 26 Ext Interrupts 24 USB Interface No USB Speed No

Hurry Up!!!!  W eekend offer only for 2 days Description: Latest UNO Bootloader. 16 Mhz operation. Package contain: 1 X ATmega328-PU with Arduino UNO bootloader

Order more than one piece to save shipping cost. You can contact us at +91 for any question or concern. Kit Details Package Include 1 Piece

Atmel Atmega328-PU with Arduino UNO bootloader PDIP pin out. Latest UNO Bootloader. 16 Mhz operation Can be used to replace Atmega328 on UNO board Please Note:- Single Atmega328 Chip with UNO bootloader. You can repair faulty UNO board replace with this chip. Please contact us for any doubt.Please give us positive feed back.Your feed back is very important for us. Happy to help you.We shipped our material within 2 working days after getting confirmation of payment. contact us- Mob:-     (From 10 AM to 9 PM)   

100 % GENUINE!!!  IMPORTED!!!  QUALITY CHECKED!!! LIMITED STOCK LOWEST PRICE CHALLENGE!!! Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1 pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board.  SHIPPING: all over india By speed post  (plz make sure speed post service is available at your city), generally takes 3-7 days to deliver FEEDBACK: PLZ GIVE 5 STAR RATINGS AND  POSITIVE  FEEDBACK  IT'S VERY IMPORTANT FOR US 100% positive feedback and satisfaction of buyers are our moto

Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board. Shipping: by speed post plz make sure speed post service is available at your city, generally takes 3-7 days to deliver after getting cleared payment Feedback: plz give 5 star ratings and positive feedback its very important for us

use coupon  COUPONDUN8 to get 7.5 % off Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board. Shipping: always free by speed post please make sure speed post service is available at your city, generally takes 3-7 days to deliver after getting cleared payment Feedback: please  give 5 star ratings and positive feedback it's very important for us

Product Description 1. ATMEL ISP standard 10PIN convert to standard 6PIN interface 2. 10PIN to 6PIN ISP Adapter board  Package Included: 1pcs 10 Pin to Standard 6 Pin Adapter Board for ATMEL AVRISP USBASP STK Pin To 6 Pin Programming Adaptor Quick Overview Perfect For Programming Any 6 Pin Programmable Boards Such As Arduino Boards.  Details In The Avr Isp (In System Programming). 6 Pin Or 10 Pin Frc Connectors Are Used. If Your Avr Isp Programmer Have 10 Pin Frc Connector And The Target Microcontroller Has 6 Pin Frc Connector For Isp Or Vice Versa Then 6 To 10 Pin Avr Isp Converter Is Very Handy For Insuring Compatibility Between Any Type Of Frc Connectors Between Programmer And The Target Board. Shipping: always free by speed post please make sure speed post service is available at your city, generally takes 3-5 days to deliver after getting cleared payment Feedback: please  give 5 star ratings and positive feedback it's very important for us

AVR USB Programmer with case USBasp USBISP for ATMEL ATmega ATtiny microcontrollers. Painless AVR controller programming   Product Description: Main Features: ·         Brand new and high quality ·         Support for Linux, Mac OS X and Windows ·         5 KB/sec maximum write speed. ·         10 pin ISP interface. ·         Can be used with Khazama, AVRDUDE, PonyProg and other ·          Support for AVRDUDE from version 5.2 onwards   Supported devices: Mega Series: ATmega8 – ATmega48 – ATmega88 – ATmega168 – ATmega328 – ATmega103 – ATmega128 – ATmega – ATmega – ATmega16 – ATmega161 – ATmega162 – ATmega163 – ATmega164 – ATmega169 – ATmega – ATmega – ATmega32 – ATmega324 – ATmega329 – ATmega – ATmega64 – ATmega640 – ATmega644 – ATmega649 – ATmega – ATmega – ATmega Tiny Series ATtiny12 – ATtiny13 – ATtiny15 – ATtiny25 – ATtiny26 ATtiny45 – ATtiny85 – ATtiny   Classic Series AT90S – AT90S – AT90S – AT90S – AT90S AT90S – AT90S – AT90S AT90S  CAN Series AT90CAN128 PWM Series AT90PWM2 – AT90PWM3 Package includes: ·         1 x USB AVR Programmer with case ·         1 x 10-pin programming cable ·         A plastic container box.   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·        In case you find any problem

With this board you can develop and prototype with ATMEGA16/ATMEGA pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters.   FEATURES AVR Development Board for Atmel ATMEGA ISP Socket for Flashing On board Regulated Power Supply 5v,12v supplys Easy to test with Burg Connecters wires An RS232 Serial Port 7Seg Mulitplexed Display DC Power Supply Connector(12v Ac or Dc) READY INTERFACE For LCD display 2linex16Character 24Cxx (I2C) (EEPROM) RTC (DS LED array Matrix Key Pad 4 Interrupt Switches +12v Relay (one) Package Content   AVR Development Board (WITH CHIP MAX232) Burg Connecters 20 Nos Female to Female.

ATmega16is an 8-bit high performance microcontroller of Atmel’s Mega AVRfamily with low power consumption. Atmega16 is based on enhanced RISC (Reduced Instruction Set Computing, Know more about RISC and CISC Architecture) architecture with 131 powerful instructions. Most of the instructions execute

1.      About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

Set of 4 Pcs AVR40 Base Board  Kit.  For Electronic project.  Atmel AVR - 40 Pin Base Boar d (For ATmega16, AT mega 32,Microcontroller) 1 Pcs 6 Digital Sensors Board for Line Follower    1 Pc 16X2 LCD Board for Display 1 Pc L298N Dual H-Bridge Motor Driver Board. **FREE**4 Pcs FRC Cable. ** Does not Include Any Microcontroller ** Atmel AVR - 40 Pin Base Board AVR-40Pin Development Board -For 40 pin AVR like ATMEGA16, ATMEGA32 etc it Comes without   micocontroller 1 Pc L298N Dual H-Bridge Motor Driver Board. 6 Digital IR - Photodiode Sensors Array for LFR Robot 6 IR-Photodiode Sensors Array- for Line following robot (LFR) and micro-mouse robot  (Digital out, Independent Manual Adjustable) Ideal for LFR (line-follower Robot) obstacles avoiding robots obstacles chasing robot side wall sensor maze solving robots 16x2 LCD Display Board Box Header Connection > LCD Connection (4Bit Mode) Pin#1   > RS(4) Pin#2   > EN(6) Pin#3   > D4(11) Pin#4   > D5(12) Pin#5   > D6(13) Pin#6   > D7(14) Pin#7   > No Connection Pin#8   > No Connection Pin#9   > Gnd () Pin#10 > +5V (2) Note Pin#5 of LCD (RW) is forcefully connected to Ground L298N Dual H-Bridge Motor Driver Board New Improved L298 Dual H-Bridge Board - Ideal for robot motor control, smart  full feature,compact, Compatible with AVR - 40 Board 10 Pin Box Header Connection Description Pin1= ENABLE B Pin2= ENABLE A Pin3= INPUT-3 Pin4= INPUT-1 Pin5= INPUT-4 Pin6= INPUT-2 Pin7= NOT CONNECTED Pin8= NOT CONNECTED Pin9= Ground Pin10=Vcc +5Volt    Fore More Details please refer Datasheet of L298N. ****FREE**** 4 Pcs of 10 Wire FRC (Flat Ribbon Cable) Cable - 15 cm. ,with female connectors on both ends. Please Clear Any Doubts "BEFORE" Buying any products form us. Fast Shipping via*      * Under 's Power-Ship program Please Check your (destination) pin-code serviceable at respective courier company or not other vise we will different courier company /Indian Speed post. Please Clear Any Doubts "BEFORE" Buying any products form us.     Please Visit our Shop: Chips-N-Boards   http://stores..in/Chips-N-Boards For Microcontroller Programmers, Robotics Stuff,Embedded Products and other Electronics Components.                                                                                                        For more assistance call: +91-, "DISCLAIMER: The Seller DSR rating shown above is for representation purpose only, Please check our feedback profile to know my current DSR ratings "   Any Octroi or other local taxes if applicable will be paid by buyer only. .in Toll free Helpline: Powered by Turbo Lister

ARDUINO UNO R3 DEVELOPMENT BOARD ATMEGA328P | CH340G | WITH USB CABLE   Package Include: ·         1X ATMEL ATmega328P  CH340G BOARD, USB Cable included   Product description:   Main changes from the older version:  CH340G replace ATmega16U2 AUTO POWER SELECTION FEATURE ENABLED Technical Details: Microcontroller: ATmega328P Operating voltage: 5V  Input Voltage (recommended): 7-12V (EXTERNAL), 5V(USB) Digital I/O Pins: 14 (of which 6 provide PWM output)  Analog Input Pins: 6  DC Current per I/O Pin: 40mA  DC Current for 3.3V pin: 50mA  Flash Memory: 32 KB (ATmega328P) of which 0.5KB used by bootloader  SRAM: 2 KB (ATmega328P)  EEPROM: 1 KB (ATmega328P)  Clock Speed: 16 MHZ  USB Chip CH340G Usage Instructions: Click here for the driver software Before connecting the Board to your USB port: 1.     Download the “ch341ser.exe” file and run it. 2.     The software asks whether it can install the CH341SER.INF driver for the CH340 chip. Click INSTALL 3.     A Windows message asks whether the driver has installed correctly. Click YES. 4.     Connect your Board. 5.     From Control Panel, open Device Manager and Ports. If installed correctly you should see an entry “USB-SERIAL CH340 (COMXX) Install Arduino IDE Download Here http://arduino.cc/en/Main/Software Connect Board to Computer and open Arduino IDE. Select board as "Uno"

PRODUCT DESCRIPTION The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU   It is the first Arduino board based on a 32-bit ARM core microcontroller.  It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.  On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started.  The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.  The Arduino Due can be powered via the USB connector or with an external power supply.  A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. Technical specs AVR Arduino microcontroller Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-16V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Length mm Width 53.3 mm Weight 36 g

SAM3X8EA 32bit ARM Contex-M3 Due R3 Board Control  Arduino Due R3 AT91SAM3X8E   Description The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. Features: 1. Microcontroller ：AT91SAM3X8E   2. Operating Voltage：3.3V  3. Input Voltage (recommended)：7-12V  4. Input Voltage (limits)：6-16V  5. Digital I/O Pins ：54 (of which 12 provide PWM output)  6. Analog Input Pins：12 7. Analog Outputs Pins：2 (DAC) 8. Total DC Output Current on all I/O lines ：130 mA 9. DC Current for 3.3V Pin：800 mA   10. DC Current for 5V Pin：800 mA  11. Flash Memory：512 KB all available for the user applications  12. SRAM：96 KB (two banks: 64KB and 32KB)   13. Clock Speed：84 MHz            Driver installation and usage procedure: ·                      Install  Arduino IDE ß  (click here) no extra driver needed for this card. ·                      Connect the board to computer, OS will auto detect ARDUINO DUE ·                      If the board is not auto detected, go to hardware device manager and choose update driver than choose advanced option “install from specific location” and point to the directory where your Arduino IDE is installed e.g. ”C:/program files/arduino-1.0.2/drivers” ·                      Launch Arduino IDE, select board as “arduino DUE” ·                      Select the com port OS created for the card(control panel  à  device manager) ·                      Open basics  à  blink sketch and upload. Package: 1 MCU BOARD  + 1 USB cable

         PRODUCT DESCRIPTION The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU   It is the first Arduino board based on a 32-bit ARM core microcontroller.  It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.  On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started.  The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.  The Arduino Due can be powered via the USB connector or with an external power supply.  A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. Technical specs AVR Arduino microcontroller Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-16V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Length 101.52 mm Width 53.3 mm Weight 36 g

The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout. The Arduino Due can be powered via the USB connector or with an external power supply. The power source is selected automatically. External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Leads from a battery can be inserted in the Gnd and Vin pin headers of the POWER connector. The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is 7 to 12 volts.

Pro Mini electronic building blocks Interactive Media ATMEGA328P 5V/16M for arduino Compatible Nano Mini Pro is a microcontroller board. It has 14 digital input / output pins (of which 6 can be used as PWM outputs), Eight analog inputs, a 16MHz resonator, a reset button, mounting hole pin head. Technical parameters: 14 Digital input / output port: RX, TX, D2 – D13 8 analog inputs: A0 – A7 1 pairs of ports TTL level serial transceiver: RX / TX 6 PWM ports: D3, D5, D6, D9, D10, D11 Using Atmel AtMega328P-AU MCU Support serial download Support for external 3.3V – 12V DC power supply Support 9V battery supply Clock frequency: 16MHz Size: 33.3 x 18.0 mm   Note: If uploading sketches using the Arduino IDE and selecting the corresponding Pro Mini board fails, follow these steps to update the bootloader: Prepare an Arduino Uno, Mega or similar to act as ISP as described at http://arduino.cc/en/Tutorial/ArduinoISP Wire it up as shown

Mini Pro is a microcontroller board. It has 14 digital input / output pins (of which 6 can be used as PWM outputs), Eight analog inputs, a 16MHz resonator, a reset button, mounting hole pin head. Technical parameters: 14 Digital input / output port: RX, TX, D2 – D13 8 analog inputs: A0 – A7 1 pairs of ports TTL level serial transceiver: RX / TX 6 PWM ports: D3, D5, D6, D9, D10, D11 Using Atmel AtMega328P-AU MCU Support serial download Support for external 3.3V – 12V DC power supply Support 9V battery supply Clock frequency: 16MHz Size: 33.3 x 18.0 mm   Note: If uploading sketches using the Arduino IDE and selecting the corresponding Pro Mini board fails, follow these steps to update the bootloader: Prepare an Arduino Uno, Mega or similar to act as ISP as described at http://arduino.cc/en/Tutorial/ArduinoISP Wire it up as shown

Micro SD Storage Board Mciro SD TF Card Memory Shield Module SPI For Arduino     Product information Features:   Support Micro SD Card, Micro SDHC card (high-speed card) The level conversion circuit board that can interface level is 5V or 3.3V Communication interface is a standard SPI interface Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground,  VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply; Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal; Micro SD card connector: yes since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, easy to install positioning, to achieve inter-module combination; Specifications: Power supply:4.5V - 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size:45 x 28mm Net weight:6g Package weight:16g Shipping content: 1x Micor SD TF Card Shield Expansion Board for Arduino/PIC/ATMEL

This is programmer for  89  series microcontrollers like  89C51,C52,S51,S52,C,C  and such series from Atmel. Board also supports various 8 pin serial EEPROM ICs. ZIF socket enables easy insertion and removal of devices for programming. Programming is very fast and reliable since it is USB based. No external power required since it is powered from USB port itself. Features •     Supports  89C51,C52,S51,S52,C,C  series & serial EEPROM devices. •     Powered from USB port(No external power required). •     High speed writing (8kb flash file

Description: This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. The Uno R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The Uno R3 works with all existing shields but can adapt to new shields which use these additional pins. Special SMD Version:Because Atmel is moving more and more of their production capacity to surface mount ICs, the DIP packaged ATmega is becoming more and more difficult to get. To keep up with demand, we now offer the Arduino Uno R3 with an SMD ATmega. Features: ATmega328 microcontroller Input voltage - 7-12V 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs 32k Flash Memory 16Mhz Clock Speed We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

LilyPad 328 ATmega328P Main Board compatible with Arduino’s IDE Features: Brand new and high quality The LilyPad Iduino is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The LilyPad Iduino can be programmed with the software. The ATmega328V on the LilyPad comes preburned with a bootloader that allows you to upload new code to it with the software. You can also bypass the bootloader and program the ATmega through the ICSP (In-Circuit Serial Programming) header. The LilyPad should only be programmed with software versions 0010 or higher. You can program it with earlier versions, but all of the time related functions will be switched off (making them twice as slow as they should be). Warning: Do not power the LilyPad with more than 5.5 volts, or plug the power in backwards: you'll kill it. 328 Main board; The Digital I/O Digital input/output terminal, a total of 0 ~ 13; The Analog I/O Analog input/output terminal, a total of 0 ~ 5; Support the ISP download function; Support the TX/RX terminals; Support the AREF terminals; Support the six groups of PWM terminal (Pin11 Pin10, Pin9, Pin6 and Pin5, responsible); The input voltage: 3.3 V DC; Using Atmel Atmega328V - 20 pu microcontroller; Specifications: Microcontroller: ATmega328V Operating Voltage: 2.7-5.5 V Input Voltage: 2.7-5.5 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 6 DC Current per I/O Pin: 40 mA Flash Memory: 16 KB (of which 2 KB used by bootloader) SRAM: 1 KB EEPROM: 512 bytes Clock Speed: 8 MHz Package includes: 1* LilyPad atmega 328 Main board Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.