Serial ttl

See our ratings Add this shop to my favorites Serial TTL Controlled 4 Channel Relay Module: Control by ASR-M08-A Voice Board Module or Bluetooth ₹ Availability:

Kootek PL USB to Serial TTL UART Module Converter Adapter. A handy USB to TTL converter based on the PLHX.3 LEDs are on-board to indicate power data reception and data transmission. A 5V and 3.3V output is available--you can power your project directly from the USB port so it functions as a USB power supply too. The 5-pin I O is clearly labelled on the board.Excellent driver support--drivers are available for Windows 98 to Windows 7 (32 bit and 64 bit) Mac OS 8 to OS X (32 bit and 64 bit) and Linux. Even Android is supported!

NooElec PL USB to Serial (TTL) Module/Adapter with Female and Male Wiring Harnesses & Test Jumper. Compatible with Windows 98 through Windows 7; Mac OS 8 through OS X Linux and Android!. A handy USB to TTL converter based on the PL LEDs are on-board to indicate power data reception and data transmission. A 5V and 3.3V output is available--you can power your project directly from the USB port so it functions as a USB power supply too. The 5-pin I O is clearly labelled on the board.Both a 5-pin female to male and a 5-pin female to female multicolor jumper cable set are included! This will allow connection to Arduino breadboards and nearly any other board with standard male or female headers.A shunt is also included

      The USB to RS232 converter board is most essential bridge needed to connect serial device to log the data to pc or laptop. If you have a development board like 8051, AVR, PIC or any other with serial UART or RS232 connector. Then use the USB to RS232 converter to connect these devices for programming or communication with the PC or Laptop.              Now a days most of the laptops does not have COM ports to connect directly with RS232 cable. So use i-labz USB to RS232 converter for interfacing. If you are planning to buy 8051, AVR, PIC or any other boards like GSM modem, GPS, Bluetooth, Finger print scanner or Ultrasonic distance finder then you must use USB to RS232 connector for connecting or troubleshooting with laptop. CP210x Driver Installation Guide - USB Driver Installation Instructions Download Terminal tool for Troubleshooting(winXP/7/8)               To test the USB to RS232 converter use windows hiighper terminal (using winXP as OS) or terminal tool. The procedure to test to setup the highper terminal is explained

Description The TTL HC-05 Bluetooth Module Serial port Bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc. Security:  Authentication and encryption Profiles:  Bluetooth serial port Speed: Asynchronous:  2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps In this now, we provide HC-05 and HC-06. HC-05 could be setting to Master or Slave by user. HC-06 has be designed Master or Slave when the factory, user couldn't change the role. Technical parameters: Bluetooth protocal:  Bluetooth Specification v2.0+EDR Frequency:  2.4GHz ISM band Modulation: GFSK(Gaussian Frequency Shift Keying) Emission power:  =4dBm, Class 2   Package Includes: 1 Piece new  TTL O/P HC06 Bluetooth Module (Slave) Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91    between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description The TTL HC-05 Bluetooth Module Serial port Bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc. Security:  Authentication and encryption Profiles:  Bluetooth serial port Speed: Asynchronous:  2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps In this now, we provide HC-05 and HC-06. HC-05 could be setting to Master or Slave by user. HC-06 has be designed Master or Slave when the factory, user couldn't change the role. Technical parameters: Bluetooth protocal:  Bluetooth Specification v2.0+EDR Frequency:  2.4GHz ISM band Modulation: GFSK(Gaussian Frequency Shift Keying) Emission power:  =4dBm, Class 2   Package Includes: 1 Piece new  TTL O/P Bluetooth Module (Master + Slave) KG037 Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description The TTL HC-05 Bluetooth Module Serial port Bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc. Security:  Authentication and encryption Profiles:  Bluetooth serial port Speed: Asynchronous:  2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps In this now, we provide HC-05 and HC-06. HC-05 could be setting to Master or Slave by user. HC-06 has be designed Master or Slave when the factory, user couldn't change the role. Technical parameters: Bluetooth protocal:  Bluetooth Specification v2.0+EDR Frequency:  2.4GHz ISM band Modulation: GFSK(Gaussian Frequency Shift Keying) Emission power:  =4dBm, Class 2   Package Includes: 1 Piece new  TTL O/P Bluetooth Module (Master + Slave) KG037 Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

Description The TTL HC-05 Bluetooth Module Serial port Bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc. Security:  Authentication and encryption Profiles:  Bluetooth serial port Speed: Asynchronous:  2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps In this now, we provide HC-05 and HC-06. HC-05 could be setting to Master or Slave by user. HC-06 has be designed Master or Slave when the factory, user couldn't change the role. Technical parameters: Bluetooth protocal:  Bluetooth Specification v2.0+EDR Frequency:  2.4GHz ISM band Modulation: GFSK(Gaussian Frequency Shift Keying) Emission power:  =4dBm, Class 2   Package Includes: 1 Piece new  TTL O/P HC06 Bluetooth Module (Slave) Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91  9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

HLK-RM04 Serial Uart to Ethernet Switch WIFI Module with antenna and HLK-RM04 UART to WIFI  Module Test Base Board   Description Product features. 
 1). UART to WIFI Wireless Module ， UART to Ethernet Module ， Ethernet to WIFI Module ， UART server module ， Make your Serial Device connected to the Internet easily. Double Data Rate All transparently. Guarantee the highest limit of Usability and Compatibility. 
 2). The module integrated m adaptive Ethernet interface.The highest baud rate up to Kbps of the serial communication.and the highest rate of TTL serial port is 500KBPS. 
 3). Each module

Prolific USB-to-Serial TTL Module Prolific 3v PL-HXD Module. SALIENT FEATURES   USB to serial port   3.3V/5V external power supply   PL, mini USB, UART interface   Compatible with development board interface of ViewTool   Fully open source application

Product Description This is a wifi solution based on IC ESP from Espressif, very price competitive wifi module, and also great function. Bring your project to the internet of things easily! Features: Very competitive price AP, STA, AP+STA modes available. Very simple AT commands, easy to use. internal LWIP interface. Only four pins interface, VCC-3V3, GND, TXD and RXD. Current firmware V091 for all stock, new reserved reset and CH_PD (for updating) pins available, you can refresh the firmware now. All using new ESPex new chip, old chip is not available anymore. Pin description Pin High Status Low Status Note VCC, GND Use standalone power source, or large capacitor, all power of this module from external TXD, RXD The serial port RST - restart CH_PD Flash boot and Update Mode - chip enable, so always connect to high status with VCC GPIO0 - Update mode GPIO2 - - GPIO 15 (when avaialble) NC Flash boot Mode Only for a few version, Wi07-3 GPIO 12 GPIO 13 GPIO 14 GPIO 16 Hardware RST No need any pull-up   AT Commands Format Baud rate at (new line) use option "send new line" or 'carriage return' for each command x is the commands Set Inquiry Test Execute AT+ = AT+ ? AT+ =? AT+ AT+CWMODE= AT+CWMODE? AT+CWMODE=? - Set the network mode Check current mode Return which modes supported - Commands carefully there are must be no any spaces between the " and IP address or port Commands Description Type Set/Execute Inquiry test Parameters and Examples AT general test basic - - - - AT+RST restart the module basic - - - - AT+GMR check firmware version basic - - - - AT+CWMODE wifi mode wifi AT+CWMODE= AT+CWMODE? AT+CWMODE=? 1= Sta, 2= AP, 3=both, Sta is the default mode of router, AP is a normal mode for devices AT+CWJAP join the AP wifi AT+ CWJAP =, AT+ CWJAP? - ssid = ssid, pwd = wifi password AT+CWLAP list the AP wifi AT+CWLAP AT+CWQAP quit the AP wifi AT+CWQAP - AT+CWQAP=? AT+ CWSAP set the parameters of AP wifi AT+ CWSAP=,,, AT+ CWSAP? ssid, pwd, chl = channel, ecn = encryption; eg. Connect to your router: AT+CWJAP="www.shanrittech.com","helloworld"; and check if connected: AT+CWJAP? AT+CWLIF check join devices' IP wifi AT+CWLIF - - AT+ CIPSTATUS get the connection status TCP/IP AT+ CIPSTATUS,,,, = client or server mode AT+CIPSTART set up TCP or UDP connection TCP/IP 1)single connection (+CIPMUX=0) AT+CIPSTART=,,; 2) multiple connection (+CIPMUX=1) AT+CIPSTART=,, - AT+CIPSTART=? id = 0-4, type = TCP/UDP, addr = IP address, port= port; eg. Connect to another TCP server, set multiple connection first: AT+CIPMUX=1; connect: AT+CIPSTART=4,"TCP","X1.X2.X3.X AT+CIPMODE set data transmission mode TCP/IP AT+CIPMODE= AT+CIPSEND? 0 not data mode, 1 data mode; return "Link is builded" AT+CIPSEND send data TCP/IP 1)single connection(+CIPMUX=0) AT+CIPSEND=; 2) multiple connection (+CIPMUX=1) AT+CIPSEND=, AT+CIPSEND=? eg. send data: AT+CIPSEND=4,15 and then enter the data. AT+CIPCLOSE close TCP or UDP connection TCP/IP AT+CIPCLOSE= or AT+CIPCLOSE AT+CIPCLOSE=? AT+CIFSR Get IP address TCP/IP AT+CIFSR AT+ CIFSR=? AT+ CIPMUX set mutiple connection TCP/IP AT+ CIPMUX= AT+ CIPMUX? 0 for single connection 1 for multiple connection AT+ CIPSERVER set as server TCP/IP AT+ CIPSERVER= [,] mode 0 to close server mode, mode 1 to open; port = port; eg. turn on as a TCP server: AT+CIPSERVER=, check the self server IP address: AT+CIFSR=? AT+ CIPSTO Set the server timeout AT+CIPSTO= AT+CIPSTO?

Product Description This is a wifi solution based on IC ESP from Espressif, very price competitive wifi module, and also great function. Bring your project to the internet of things easily! Features: Very competitive price AP, STA, AP+STA modes available. Very simple AT commands, easy to use. internal LWIP interface. Only four pins interface, VCC-3V3, GND, TXD and RXD. Current firmware V091 for all stock, new reserved reset and CH_PD (for updating) pins available, you can refresh the firmware now. All using new ESPex new chip, old chip is not available anymore. Pin description Pin High Status Low Status Note VCC, GND Use standalone power source, or large capacitor, all power of this module from external TXD, RXD The serial port RST - restart CH_PD Flash boot and Update Mode - chip enable, so always connect to high status with VCC GPIO0 - Update mode GPIO2 - - GPIO 15 (when avaialble) NC Flash boot Mode Only for a few version, Wi07-3 GPIO 12 GPIO 13 GPIO 14 GPIO 16 Hardware RST No need any pull-up AT commands §   Baud rate: (from v0.90, v0.80 and older: ) §   The AT part of the command can be written large or small, however, the following command must always be written large §   Make sure that before, after and within the command no spaces (space) occur General AT commands AT command Description Parameter Example AT Test command, are always "OK" back AT AT + RST Reset of the module, the module's boot messages followed by  ready  back AT + RST AT + GMR Querying the Firmware Version AT + GMR WiFi AT commands AT command Description Parameter Example AT + CWMODE =  Setting the WiFi mode  1) Station 1 =  2 = Access Point  3 = Both AT + CWMODE = 1 AT + CWMODE? Query WiFi mode AT + CWMODE? AT + CWMODE =? Query of possible settings for WiFi mode AT + CWMODE =? AT + CIPMUX = Using multiple connections 0 = single compound  1 = Multiple connections AT + CIPMUX = 1 AT + CIPMODE = Setting the data mode 0 = transparent  1 = Data AT + CIPMODE = 1 AT + CIPMODE? Output of the data set mode AT + CIPMODE? WiFi commands (Station / client) AT command Description Parameter Example AT + CWJAP =, Connecting to WiFi network ssid "SSID"  pass "password" AT + CWJAP = "makerday", "M4k3rd4y" AT + CWJAP? Output of the currently connected WiFi network AT + CWJAP? AT + CWLAP Output of available APs  2) AT + CWLAP AT + CWQAP Closes the connection to an access point AT + CWQAP AT + CIFSR Issue its own IP address AT + CIFSR WiFi commands (Access Point) AT command Description Parameter Example AT + CWSAP =, [,,] Set the access point parameters  3) ssid "SSID"  pass "password"  chan "channel"  enc "Encryption"  (0 = Open  1 = WEP  WPA_PSK 2 =  3 = WPA2_PSK  4 = WPA_WPA2_PSK) AT + CWSAP = "makerday", "M4k3rd4y" 5.3 AT + CWSAP? Output the current settings for the AP AT + CWSAP? AT + CWLIF Lists stations connected IPs 4) AT + CWLIF WiFi commands (IP Client) AT command Description Parameter Example AT + CIPSTATUS Output status of the IP connection (s) AT + CIPSTATUS AT + CIPSTART =,, Creating an IP connection with AT + CIPMUX = 0 type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND = Sending data over a single compound  5) len: Data length AT + CIPSEND = AT + CIPCLOSE Close a single TCP or UDP connection AT + CIPCLOSE AT + CIPSTART =,,, Creating an IP connection with AT + CIPMUX = 1 id: 0-4  type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND =, Send data via merhere compounds 6) id: 0-4  len: Data length AT + CIPSEND = AT + CIPCLOSE = Close one of several TCP or UDP connection id: 0-4 AT + CIPCLOSE = 1 WiFi commands (IP server) AT command Description Parameter Example AT + CIPSERVER = 1 [,] Starts the TCP server port: TCP port AT + CIPSERVER = AT + CIPSERVER = 0 Terminates the TCP server AT + CIPSERVER = 0 AT + CIPSTO = Sets timeout for TCP server timeout = s AT + CIPSTO = 180 AT + CIPSTO? Specifies timeout of TCP server AT + CIPSTO? If a TCP server is started, it can handle up to 5 simultaneous connections. Other compounds can be created, but only served when others are closed or terminated by timeout. The module incoming data directly with the prefix  + IPD  issued: + IPD,   OK   + IPD, 0.6: ON   OK The output is divided as follows: + IPD,,, It is  id  the ID of the compound (0-5),  len  the length of the resulting data packet and  data  contains the data received from the client. In the above example as first sends compound 1 the value   and then connect the string 0  ON     Powered by Turbo Lister

  This is a plug and play GSM Modem with a simple to implement RS232, TTL serial and USB interface. It works on frequencies 900/ 1800 MHz. Use it to send SMS, make and receive calls, and do other GSM operations by simple AT commands through a serial interface from microcontrollers and computers. It uses the popular SIM900A module for all its GSM operations. It comes with a standard RS232 interface which can be used to easily interface the modem to microcontrollers and computers. Through USB, the modem can be operated from a computer to send/receive calls, messages, etc    The modem consists of all the external circuit required to start experimenting with the SIM900A module like the power regulation, external antenna, SIM Holder, etc. Features Uses the extremely popular SIM900A GSM module USB communication allows direct communication with computers Provides the industry standard serial RS232 interface for easy connection to computers and other devices Provides serial TTL interface for easy and direct interface to microcontrollers Power, Status and Network LEDs for easy debugging Onboard MIC and Speaker circuits and 3.5mm audio connectors for direct connection to mics and speakers Can be used for GSM based Voice communications, Data/Fax, SMS,GPRS and TCP/IP stack Can be controlled through standard AT commands Module’s operation mode can be controlled through the PWR Key connected to the PWRKEY pin (refer the SIM900A datasheet for more information) Comes with an onboard wire antenna for better reception. Board provides an option for adding an external antenna through an SMA connector The SIM900A allows an adjustable serial baudrate from 1200 to 115200 bps Modem has low power consumption of 0.25 A during normal operations and around 1 A during transmission Operating Voltage: 7 – 15V AC or DC (board has onboard rectifier) Related Documents Stater Guide AT Commands Set   Download Terminal tool for Troubleshooting(winXP/7/8)

The ESP modules offer a very affordable way to expand microcontroller projects with an Internet connection. The good range, ease of configuration and especially the low price, these modules are very attractive for IoT projects of all kinds. Data sheet and related link will be provided once you buy the product and email with subject as esp to Plz watch video for more details https://www.youtube.com/watch?v=7zD92FXQc8Q&feature=youtu.be Note: All inputs are not 5V tolerant of ESP and may be used only with 3.3V. For the sample arduino code you need to send a mail to with subject as "esp code"  after buying All Shipping through powership Label Signal VCC 3.3V (3.6V max) Supply Voltage GND Ground TXD Transmit Data (3.3V level) RXD Receive Data (3.3V level!) CH_PD Chip Power down: (LOW = Power down active) GPIO0 General Purpose I / O 0 GPIO2 General Purpose I / O 2 RST Reset (LOW = Reset active)

Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. INTRODUCTION   Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. with your microcontroller. This module can easily be used with Positron Development Boards.  SALIENT FEATURES This module has 4 pins viz. Receiver, Transmitter, Vcc and Ground These four pins can easily be connected to any of the Transmitter, Receiver, Vcc and Ground of a micro controller development board The module uses MAX232 IC and can be easily connected to your laptop using Positron’s DB9 cables

1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU. Order more than one piece to save shipping cost. You can contact us at + for any question or concern. Device Details This is a USB to Serial Converter Module based on PL-HX IC Device Specifications Based on PL-HX IC 5 Pins - 3.3V, 5.0V, TXD, RXD, GND Can be used to program Arduino Pro Mini. Package Include 1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU 5 x Femalre to Femalre Jumper Wires (Note: Wire Colour May Vary) About Us We are a small company based

1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU. Order more than one piece to save shipping cost. You can contact us at +91 94625 64100 for any question or concern. Device Details This is a USB to Serial Converter Module based on PL-2303HX IC Device Specifications Based on PL-2303HX IC 5 Pins - 3.3V, 5.0V, TXD, RXD, GND Can be used to program Arduino Pro Mini. Package Include 1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU 5 x Femalre to Femalre Jumper Wires (Note: Wire Colour May Vary) About Us We are a small company based

Product Description 1x FT232RL USB TO TTL 5V 3.3V Download Cable To Serial Adapter Module For Arduino Shipped via powership. Fast ship - Bluedart/Fedex/DHL/Aramex FT232RL USB TO TTL 5V 3.3V Download Cable To Serial Adapter Module For Arduino Features: 100% Brand new and high quality Material: PCB + Electronic Component Support 3.3V, 5V Main Color: Red Chipset: FT232RL USB power has over current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator Pin definition: DTR,RXD,TX,VCC,CTS,GND Pitch:2.54mm Module Size: About 36mm(length)*17.5mm(width) Interface: Mini USB Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Description Serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc. This is HC-05 module, you can configure it to use it as master or slave mode by AT-commands. Level logic: TTL level: normal data represented using binary fixed +5 V equivalent to logic "1", 0V is equivalent to logic "0", referred to as a TTL signal system is the positive logic Package Content: 1 x HC-05, master-slave Bluetooth Module (Arduino compatible) 1 x AT commands Manual (by email) Voltage Requirement: Maximum Voltage 5V, can be used directly with any 5V microcontrollers.

Description Mini RS232 To TTL MAX Converter Adaptor Module Serial Port Board Brand new and high quality. A converter board for electrical levels The highest baud rate: not recommended More than 120 KBPS Technical parameters: Voltage range: 3 v to 5 v Size: 9.4 mm*15.9 mm   Package Contents: 1 x Mini RS232 To TTL MAX Converter Adaptor Module Serial Port Board Feedback: We provide good quality products & maintain high customer service standards.  We strive for 100% positive feedback for our service.  For assistance, please contact us on  Message  or  If you are satisfied with our service we request you to please leave us a positive feedback and 5 Star DSR ratings

CP Serial Converter USB 2.0 To TTL UART 5PIN Module +  Free Dupont line 5 pc female to female! Description:     Name: CP, USB to TTL Module     Baud Rate Range: Mbps     Control chip: CP     Working voltage: 4V-5.25V     Support: Windows 98SE, , XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40     Output voltage: Dual voltage output (3.3V and 5V)     Output indicator: Power indicator, TXD indicator     Output current: 100mA (with current limiting protection)     5 pins for 3.3V, TXD, RXD, GND & 5V   Packaging List:     1 x USB to TTL Module     5 x Dupont Wire

Other Items Feedbacks About Us Contact Us Add To Favorites CNB816-USB to Serial UART / TTL (3.3V/5V) Converter for Android Driver Solution PLHXD Android Driver Solution    Prolific provides Android USB Host API driver solution (NO root permission needed) for connecting PL USB-to-Serial devices to Android-powered devices with USB Host API mode support. The PL Android JAVA driver library allows customers and developers to write Android applications to interface their PL RS-232/UART devices with millions of Android USB host devices like Smartphones, Tablets, and Smart TVs.     Download: PL Android USB Host API SDK (vb) Requirements: --------------------- - USB Device with PLHXD, PLEA, or PLRA controller chip    NOTE: PLHXA and PLXA are not supported (Discontinued Products) - Android-Powered Device (Tablet/Phones) with USB Host Mode API Support - Android 3.2 and above OS versions Product Applications: Single-chip upgrade solution for Legacy RS232 devices to USB interface USB to RS232 converters/cables/dongles Healthcare/Medical USB Interface Data Transfer Cable Personal Infotainment/Media Player Docking USB Interface Cellular/PDA USB Interface Data Transfer Cable Serial-over-IP Wireless Solution USB Barcode/Smart Card Readers GPS/Navigation USB Interface Point-of-Sale (POS) Terminals/Printers PC Docking Station/Port Replicators Industrial/Instrumentation/Automation Control USB Interface USB Modem/Wireless/Zigbee USB Interface Description: This is a newly designed product, using the Taiwan prolific production company PLHXD chips, PLHXD perfectly compatible with win XP/VISTA//Android OTG. The PL-HXD is a low cost and high performance USB-to-Serial Bridge Controller. The PL-HXD provides a convenient solution for connecting an RS-232 full-duplex asynchronous serial device to any Universal Serial Bus (USB) capable host. The PL-HXD highly compatible drivers could simulate the traditional COM port on most operating systems allowing the existing applications based on COM port to easily migrate and be made USB ready. Full compliance with the USB Specification v1.1 Supports RS-232 serial interface with Programmable baud rate from 75 bps to 12 Mbps. Supports RS422/RS485 interface. Extensive flow control mechanism like adjustable high/low watermark level, automatic hardware or software flow control, and inbound data buffer overflow detection. Our Other Products Images Gallery   Note "Anything not listed is excluded" Payment is accepted by Paisa Pay only. Paisa Pay is the Safest mode of Payment. Shipping will be done within 1 -3 working days (Else you will be intimated) under Powership hence your parcel will be booked under Fedex/ Bluedart,if your location is not covered under powership we will send by Speedpost/Indiapost.Kindly check your pin code before placing the order. Please enter correct / complete serviceable address while placing your order, As we will not be able to change an address after order confirmation with Powership.   Buyer has to pay the OCTROI charges where ever it's applicable. Courier may also levy service charge on Octroi Payment. After you receive the item, DO NOT FORGET to CONFIRM THE ITEM RECEIPT. Check your pin code for Fedex: Click Here Check your pin code for Bluedart: Click Here      For any type of support Please feel free to contact: AM-6:30PM, Monday-Saturday) email: .in Toll free Helpline: FREE ITEM  MUST BE RETUNED WITHIN:    7 DAYS REFUND WILL BE GIVEN AS:  Merchandise Credit Return Policy details:  If the items are not as described, we will offer a Merchandise Credit. In most cases this will be minus shipping and fees, although if it was a blatant mistake by us we'll pick up everything. Bottom line, we want you happy! We try to be fair and accurate with all my auctions and descriptions. Please read each auction and bid carefully. We give you the information that is supplied by our vendors. If this information is incorrect, please email me before leaving negative feedback. This is not a retail store. All sales are final. We do not offer refunds on any item unless is grossly misrepresented. If a refund is given it will only be for the cost of the item. Shipping and Handling is non refundable. Restocking and other fees may be charged. If there is a problem, we can work together to resolve the problem. I have always been extremely fair and always try to work with my reasonable customers. Negative feedback doesn't go away and should only be left as a last resort! I strive for positive feedback, harmonious relations and even some friendships. We will make every attempt possible to resolve the issue if we made a mistake.(It happens). Please do not assume a mistake is intentional. Let us know if our service could be better!! Electronic components /spare parts doesnot cover any sort of warrenty (either operational or manufacturer) unless stated otherwise To avail the Manufacturer Warranty, the buyer needs to contact the respective service centre of the company. To avail the Seller Warranty, the buyer needs to send the product to the seller, with Proper packing & Shipping Cost. Most Important Please Leave Positive 5 star detailed feedback, its very Important for us.

Description Package Includes: 1 Piece new  MAX RS232 Serial Port To TTL Converter Module DB9 Connector 5V, RS232 to TTL It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91   between AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

  Description Package Includes: 1 Piece new  MAX3232 RS232 Serial Port To TTL Converter Module DB9 Connector 5V, RS232 to TTL It can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9793202258   between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

PLHK USB to TTL Rs232 Description • Built-in TTL COM PC-PLHX Chip  • Standard USB type A male and TTL 4 pin connector  • Cable length: mm ( in)  • Simple and Easy way to give USB support to your designs  • Available for Linux, Mac, WinCE and Windows (XP, ), Vista, Win 7，  • NOT WINDOWS 8 compatible  • Black cable-----GND  • Green cable----TXD  • White cable----RXD  • Red cable ---- VCC (5V)  PL Windows Driver Download Driver PLUSBtoTTL Serial Debugger Module Use 1, install the driver, 2, restart the computer, 3, the module is plugged into the computer's USB port, the system will automatically install the driver 4, the TXD and RXD connected (that is, one with a Dupont line inserted

Connect the USB A to B Cable to USB B socket of the module and USB port of the computer, install drivers and you will be assigned a COM port through which you can communicate as you do through a SERIAL port. You can easily communicate with microcontrollers / microprocessors from your computer through the module. If you need TTL pins for communication, you can find  TX,  RX  and  GND  points on board, solder 3 berg sticks and connect it to TTL pins of microcontrollers for direct communication without DB9 connector (No need to use MAX232 / MAX for RS232 to TTL conversion

Description MAX RS232 Serial Port To TTL Converter Module DB9 Connector With Cable Brand new and high quality. It is widely used

Wireless Bluetooth RF Transceiver Module RS232 TTL (HC-06) bluetooth module better then HC-05 Allows your device to both send or receive the TTL data via Bluetooth technology wirelessly without connecting a serial cable to your computer. Works with any USB Bluetooth adapters. Default Baud Rate: ,n. Built

Product Description This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector. The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target. This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working. This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector. One of the nice features of this board is a jumper on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level). This board ship default to 5V, but you can cut the default trace and add a solder jumper if you need to switch to 3.3V. Powered by Turbo Lister

Allows your device to both send or receive the TTL data via Bluetooth technology without connecting a serial cable to your computer.     Works with any USB Bluetooth adapters. Default Baud Rate: 9600,8,1,n. Built