Digital pins

The DHT22 (RHT03) is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires careful timing to grab data. The only real downside of this sensor is you can only get new data from it once every 2 seconds, so when using our library, sensor readings can be up to 2 seconds old. Simply connect the first pin on the left to 3-5V power, the second pin to your data input pin and the right most pin to ground. Although it uses a single-wire to send data it is not Dallas One Wire compatible! If you want multiple sensors, each one must have its own data pin! Features: Low cost 3 to 5V power and I/O 1-1.5mA measuring current uA standby current 2.5mA max current use during conversion (while requesting data) Good for % humidity readings with 2-5% accuracy Good for -40 to 80°C temperature readings ±0.5°C accuracy No more than 0.5 Hz sampling rate (once every 2 seconds) Body size 27mm x 59mm x 13.5mm (1.05″ x 2.32″ x pins, 0.1″ spacing   Feature & Application: High precision Capacitive type Full range temperature compensated Relative humidity and temperature measurement Calibrated digital signal Outstanding long-term stability Extra components not needed Long transmission distance, up to 100 meters Low power consumption 4 pins packaged and fully interchangeable Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Description 100% brand new and high quality On-board ADXL345 digital output(support the I2C/SPI), low-power, compact acceleration sensor. Support 5V/3.3V voltage input, on-board RT power chip, lower pressure drop faster than the , faster load speed of response very suitable for high-noise power supply environment Common pins are leaded out, pins standard 100mil (2.54mm), convenient for the dot matrix board. Features VCC voltage module operating voltage and good power filtering; Great influence on the antenna module reception, preferably connected to the 1/4 wavelength of the antenna, typically 50 ohm single conductor, the length of the antenna 433M of about 17cm; Antenna position has also affected the reception of the module, the installation, the antenna as possible straight away from the shield, high pressure, and interference source; frequency used to receive, decode and oscillation resistor should match with the transmitter. Specification PCB size::28 (mm) x14 (mm) Color:As shown SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you    

Description 100% brand new and high quality On-board ADXL345 digital output(support the I2C/SPI), low-power, compact acceleration sensor. Support 5V/3.3V voltage input, on-board RT power chip, lower pressure drop faster than the , faster load speed of response very suitable for high-noise power supply environment Common pins are leaded out, pins standard 100mil (2.54mm), convenient for the dot matrix board. Features VCC voltage module operating voltage and good power filtering; Great influence on the antenna module reception, preferably connected to the 1/4 wavelength of the antenna, typically 50 ohm single conductor, the length of the antenna 433M of about 17cm; Antenna position has also affected the reception of the module, the installation, the antenna as possible straight away from the shield, high pressure, and interference source; frequency used to receive, decode and oscillation resistor should match with the transmitter. Specification PCB size::28 (mm) x14 (mm) Color:As shown   Feedback: We provide good quality products & maintain high customer service standards.  We strive for 100% positive feedback for our service.  For assistance, please contact us on  Message  or  If you are satisfied with our service we request you to please leave us a positive feedback and 5 Star DSR ratings

Description 100% brand new and high quality single power supply PCF operating voltage range of 2.5V-6V low standby current PCF by 3 hardware address pins addressing PCF I2C bus speed sampling rate decision 4 analog inputs programmable as single-ended or differential input automatic incremental channel selection PCF analog voltage range from VSS to VDD PCF built-track and hold circuit 8-bit successive approximation A / D converter DAC gain realized by an analog output Module Interface Description This module left and right, respectively, two-way pin external expansion interfaces, respectively, as follows: DA output interface chip on the left AOUT AINO chip analog input interface 0 AIN1 chip analog input interface 1 AIN2 chip analog input interface 2 AIN3 chip analog input interface 3 The right of the SCL IIC clock interface connected microcontroller IO port SDA IIC digital interface connected to the microcontroller IO port GND module to an external ground VCC Power Interface External 3.3v-5v   Modules red jumper instructions Module A total of three red jumper, namely the role of the following: P4 P4 jumper connected, select thermistor access circuit P5 P5 jumper connected, select photoresistor access circuit P6 P6 jumper connected, select 0-5V adjustable voltage access circuit Specification: Color: As shown

Dear Our Buyers, We have Tie up Only with DTDC COURIER. IF you are from very remote place kindly check DTDC COURIER Service Locations using the URL: http://dtdc.com/sg_locationfind.asp and place the order.   HDMI TO MICRO HDMI CABLE     Brand new and high quality. · Perfect solution for you to share all of your photos and videos with your colleagues, family and friends. · The Micro HDMI high speed male to HDMI male cable lets you instantly plug your smartphone into any TV for instant broadcasting at family get-togethers, meetings, and even tailgate parties. · This cable lets you watch videos, stream media, or view documents from your phone on a TV. Composite outputs connects your phone to your TV or entertainment system. · This is the easy streaming solution that you have been waiting for. · A must have accessory for those who would like to watch videos and work on the big screen. · The cable gets the video signal out through HDMI standard output. · Gold plated pins and grounds connections. · Length: 2MT · Fit for HTC EVO 4G, XT800, F85EXR, SH-07B, etc. · Package Included: · 1 x Micro HDMI Type D to HDMI Cable -: About Us:-   We are major Wholesale Dealers for Cables with 7 years of offline selling experience. We are here first time to take part

Dear Our Buyers, We have Tie up Only with DTDC COURIER. IF you are from very remote place kindly check DTDC COURIER Service Locations using the URL: http://dtdc.com/sg_locationfind.asp and place the order.   HDMI TO MICRO HDMI CABLE     Brand new and high quality. · Perfect solution for you to share all of your photos and videos with your colleagues, family and friends. · The Micro HDMI high speed male to HDMI male cable lets you instantly plug your smartphone into any TV for instant broadcasting at family get-togethers, meetings, and even tailgate parties. · This cable lets you watch videos, stream media, or view documents from your phone on a TV. Composite outputs connects your phone to your TV or entertainment system. · This is the easy streaming solution that you have been waiting for. · A must have accessory for those who would like to watch videos and work on the big screen. · The cable gets the video signal out through HDMI standard output. · Gold plated pins and grounds connections. · Length: 1MT · Fit for HTC EVO 4G, XT800, F85EXR, SH-07B, etc. · Package Included: · 1 x Micro HDMI Type D to HDMI Cable -: About Us:-   We are major Wholesale Dealers for Cables with 7 years of offline selling experience. We are here first time to take part

Description         1, on-board chip TLC, TLC is a serial interface DAC, its output is voltage type, the maximum output voltage is twice the value of the reference voltage, with a power-on reset function, performance than earlier current-output DAC is better, only need three serial bus can be completed 10 serial data input, easy and industry standard microprocessor or microcontroller (MCU) Interface                       2, on-board voltage reference chip TL431 can also be an external reference voltage                       3, the chip has drawn all of the pins can be controlled by the microcontroller operation                       4, Working voltage: 5V                     5, board size: 37.2 (mm) x16.9 (mm) SHIPPING ·         Product will be shipped on same day if the order is before 2pm. ·         Tracking details will be updated to by End of the Day. ·      Orders on  Saturday  after 2pm will be shipped on Monday. PAYMENT We accept payments through PaisaPay The best and fast mode of payment. PaisaPay offers all options to pay and is completely secure - by Credit Card/Debit Card/Online Bank Transfer.   FEEDBACK Leaving Negative or Neutral Feedback will not solve a problem, so please contact us if you have any questions or any complaints before leaving a Feedback.  Your feedback is important for us to grow our business on , so once you receive your product please do leave feedback. CONTACT  US Mail –       or Use "Ask a question" option on listing page. You will get response within 24hrs.                                                                                           THANK you

The Xbee shield allows an Arduino board to communicate wirelessly using Zigbee. It is based on the  Xbee module from MaxStream. The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight). It can be used as a serial/usb replacement or you can put it into a command mode and configure it for a variety of broadcast and mesh networking options. The shields breaks out each of the Xbee's pins to a through-hole solder pad. It also provides female pin headers for use of digital pins 2 to 7 and the analog inputs, which are covered by the shield (digital pins 8 to 13 are not obstructed by the shield, so you can use the headers on the board itself). The Xbee shield was created

Description The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.. The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming in Arduino ). An SD card library is not yet included in the standard Arduino distribution. Arduino communicates with both the W and SD card using the SPI bus (through the ICSP header). This is on digital pins , and 13 on the Duemilanove and pins , and 52 on the Mega. On both boards, pin 10 is used to select the W and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W or the SD card, but it must be kept as an output or the SPI interface won't work. Note that because the W and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W, set digital pin 10 as a high output. The shield provides a standard RJ45 ethernet jack. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

2.4" Inch TFT Touch LCD Display Module For Arduino Video http://youtu.be/mQ5uv9_J_0s Package 01X2.4" Inch TFT Touch LCD Display Module For Arduino UNO R3 Features Compatible with UNO, Duemilanove, Diecimila 2.4" Colour Display, Touch Screen. No soldering just plug and play Tested. Technical Details 2.4" diagonal LCD TFT display 240x320 resolution, 18-bit () color 8 bit digital interface, plus 4 control lines Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the microSD Works with Arduino UNO R3 (Leonardo not supported yet) 5V compatible! Use with 3.3V or 5V logic Onboard 3.3V @ 300mA LDO regulator 4 white LED backlight. On by default but you can connect the transistor to a digital pin for backlight control 4-wire resistive touchscreen Send an email to with Subject as TFT TOUCH DOC for the documents and links once you purchase the product we will share the related date. for related queries feel free to contact us on this number + Power Shipping Shipping Policy Providing A Valid And Working Mobile Number Is Mandatory For Us To Dispatch Your Order. In Case If We Find That The Number Provided By You During Order Placement To Be Incorrect We Reserve The Right To Cancel The Order And Your Amount Will Be Refunded To You Through Paisapay And Your Order Will Not Be Dispatched All orders will be dispatched within 3 working days or earlier. Order once placed cannot be cancelled or modified. Normal courier delivery times are 72 hrs for metro cities and upto 10 days for other areas. These times are only indicative and the actual delivery times may vary. Octroi, if any, will be additional and to be bourne by the buyer. Octroi is not included

Description 100% Brand New and High Build Quality 2.4" diagonal LCD TFT display Bright, 4 white-LED backlight, on by default but you can connect the transistor to a digital pin for backlight control Colorful, 18-bit different shades 4-wire resistive touchscreen 8 bit digital interface, plus 4 control lines Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD 5V compatible, use with 3.3V or 5V logic For Arduino UNO R3   Package Contents: 1x 2.4" TFT LCD Shield SD Socket Touch Panel Module Feedback: We provide good quality products & maintain high customer service standards.  We strive for 100% positive feedback for our service.  For assistance, please contact us on  Message  or  If you are satisfied with our service we request you to please leave us a positive feedback and 5 Star DSR ratings

DESCRIPTION 2.4 Inch Tft Touch Screen Lcd Module For Arduino. The Lcd Has Excellent Vivid Color Contrast. Spice Up Your Arduino Project With A Beautiful Large Touchscreen Display Shield With Built In Microsd Card Connection. This Tft Display Is Big (2.4 Diagonal) Bright (4 White-Led Backlight) And Colorful (18-Bit Different Shades)! Pixels With Individual Pixel Control. It Has Way More Resolution Than A Black And White Display. As A Bonus, This Display Has A Resistive Touchscreen Attached To It Already, So You Can Detect Finger Presses Anywhere On The Screen. 2.4 Diagonal Lcd Tft Display Resolution, 18-Bit () Color Spfd Controller With Built In Video Ram Buffer 8 Bit Digital Interface, Plus 4 Control Lines Uses Digital Pins 5-13 And Analog 0-3. That Means You Can Use Digital Pins 2, 3 And Analog 4 And 5. Pin 12 Is Available If Not Using The Microsd Works With Any Arduino '328 Or Mega (Leonardo Not Supported Yet) 5v Compatible! Use With 3.3v Or 5v Logic Onboard 3.3v 300ma Ldo Regulator 4 White Led Backlight. On By Default But You Can Connect The Transistor To A Digital Pin For Backlight Control 4-Wire Resistive Touchscreen We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description The Joystick Shield kit contains all the parts you need to enable your Arduino with a joystick. The shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick give your Arduino functionality on the level of old Nintendo controllers. Soldering is required, but it's relatively easy and requires minimal tools. We even have a step by step guide. All the signal pins are brought our via 2.54 pins, to make it easy to connect to any other MCU platform The momentary push buttons are connected to Arduino digital pins 2-6; when pressed they will pull the pin low (utilizing the internal pull-ups of the Arduino). Vertical movement of the joystick will produce a proportional analog voltage on analog pin 0, likewise, horizontal movement of the joystick can be tracked on analog pin 1. Technical parameters: Channels: 2 Analog X/Y Power: up to 5V   Package Includes: 1 Piece new  Game JoyStick Shield Module can be used with Arduino, Mbed, ARM or any other MCU Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91  9793202258 between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

4 channel USB Relay Board with 36 Digital/Analog I/Os USB Data Acquisition Board    Welcome to the world of Computer Automation. This USB Relay Board - U96 is a perfect companion for all your computer automation projects. It is USB based card having 4 onboard relays for switching external devices and up to 36 digital & analogue I/Os that will help you to monitor various real world scenarios using switches & different kind of sensors to monitor many parameters like Temperature, Pressure, Light, Touch, PH etc. This card is not only good for controlling Relays but a perfect example for Data Acquisition applications. It appears as a USB CDC (Communications Device Class) device when connected to USB port of a computer. This creates a Virtual Serial (Com) Port, which allows easy communication with the card. Any programming language that supports serial communications (C, C#, C++, VB, VB.NET, Perl, Java etc) can be used to communicate with U96 very easily. Easy to use commands are available to communicate with U96 which handle various tasks like Switching On/Off of Relays, Controlling Digital Inputs & Outputs, Getting analog data etc. The controller provides 4 relay outputs to control various electrical devices. Apart from this, the card has up to 36 digital input & output pins. It has also got 15 Analog input pins. All pins will be individually configured as Digital Input or Digital output or Analog input automatically as per input command. Each Digital pin can support a TTL or Schmitt Trigger Input or a 3.3V output. Each Analog pin will convert analog voltage (Between 0 to 3V) or Higher (through voltage divider) into 12 bit resolution value. The output can be raw data or converted into voltage. The raw data be converted into required form using conversion formulas. Any kind of sensor whether it is providing digital output or analogue output can be interfaced with U96 and monitored with the help of computer. For more information please download U96 User Manual from our download section at http://iknowvations.in/downloads/. If you have any questions, you can contact our support team at support@iknowvations.in

SAM3X8EA 32bit ARM Contex-M3 Due R3 Board Control  Arduino Due R3 AT91SAM3X8E   Description The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. Features: 1. Microcontroller ：AT91SAM3X8E   2. Operating Voltage：3.3V  3. Input Voltage (recommended)：7-12V  4. Input Voltage (limits)：6-16V  5. Digital I/O Pins ：54 (of which 12 provide PWM output)  6. Analog Input Pins：12 7. Analog Outputs Pins：2 (DAC) 8. Total DC Output Current on all I/O lines ：130 mA 9. DC Current for 3.3V Pin：800 mA   10. DC Current for 5V Pin：800 mA  11. Flash Memory：512 KB all available for the user applications  12. SRAM：96 KB (two banks: 64KB and 32KB)   13. Clock Speed：84 MHz            Driver installation and usage procedure: ·                      Install  Arduino IDE ß  (click here) no extra driver needed for this card. ·                      Connect the board to computer, OS will auto detect ARDUINO DUE ·                      If the board is not auto detected, go to hardware device manager and choose update driver than choose advanced option “install from specific location” and point to the directory where your Arduino IDE is installed e.g. ”C:/program files/arduino-1.0.2/drivers” ·                      Launch Arduino IDE, select board as “arduino DUE” ·                      Select the com port OS created for the card(control panel  à  device manager) ·                      Open basics  à  blink sketch and upload. Package: 1 MCU BOARD  + 1 USB cable

Introduction Joystick Module can measure position co-ordinates on X and Y axis by moving the thumbstick on top. It also contains a tactile switch that can be triggered by pressing the thumbstick down. There are many projects that need a joystick. You can use it to control the movement of a robot, positioning an electronically controlled object, etc. This can easily be connected to Arduino board, Draco board or any other microcontroller which supports reading analog and digital input. The module has 5 important connections. X,Y,Z, VCC and Ground. To make connections easier, each axis pin is extended with a separate Ground and power pins. This means, there are a total of 9 pins, each of Signal, Power and Ground. This is an analog joystick module where each movement can be calculated and action taken according to the number of steps (or angle) moved. This is better than those with only buttons that say either Up, Down, Left, Right, Center by a combination of different switches. A separate "press to select" switch can trigger any user customized action. The X and Y pins should be connect to analog read pins of the microcontroller and Z pin be connected to a digital pin. Z pin is floating and when pressed, will read a positive voltage. An additional pull-down resistor (4.7K-10K) can be added

PRODUCT DESCRIPTION The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU   It is the first Arduino board based on a 32-bit ARM core microcontroller.  It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.  On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started.  The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.  The Arduino Due can be powered via the USB connector or with an external power supply.  A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. Technical specs AVR Arduino microcontroller Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-16V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Length mm Width 53.3 mm Weight 36 g

         PRODUCT DESCRIPTION The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU   It is the first Arduino board based on a 32-bit ARM core microcontroller.  It has 54 digital input/output pins, 12 analog inputs, 4 UARTs, a 84 MHz clock, an USB OTG capable connection, 2 DAC, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.  On board CAN controller for realizing CAN Protocol. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started.  The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.  The Arduino Due can be powered via the USB connector or with an external power supply.  A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. Technical specs AVR Arduino microcontroller Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-16V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Length 101.52 mm Width 53.3 mm Weight 36 g

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328)

The Arduino Uno is a microcontroller board based on the  ATmega328  (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16  MHz  ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Summary Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16  MHz Length 68.6 mm Width 53.4 mm Weight 25 g

Package Contains 1XArduino Uno R3 1X Usb Cable for Arduino The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

Arduino UNO (Q021) The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g

Description: The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Summary Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

PRODUCT DETAILS: Arduino UNO R3 Compatible Board ATmega328P ATmega16U2 with USB cable DESCRIPTION This is a Compatible board for Arduino uno r3, not original This UNO is a 100% compatible derivative of current R3 Arduino UNO The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller;simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Features:- Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description: This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. The Uno R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The Uno R3 works with all existing shields but can adapt to new shields which use these additional pins. Special SMD Version:Because Atmel is moving more and more of their production capacity to surface mount ICs, the DIP packaged ATmega is becoming more and more difficult to get. To keep up with demand, we now offer the Arduino Uno R3 with an SMD ATmega. Features: ATmega328 microcontroller Input voltage - 7-12V 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs 32k Flash Memory 16Mhz Clock Speed We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

LilyPad 328 ATmega328P Main Board compatible with Arduino’s IDE Features: Brand new and high quality The LilyPad Iduino is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The LilyPad Iduino can be programmed with the software. The ATmega328V on the LilyPad comes preburned with a bootloader that allows you to upload new code to it with the software. You can also bypass the bootloader and program the ATmega through the ICSP (In-Circuit Serial Programming) header. The LilyPad should only be programmed with software versions 0010 or higher. You can program it with earlier versions, but all of the time related functions will be switched off (making them twice as slow as they should be). Warning: Do not power the LilyPad with more than 5.5 volts, or plug the power in backwards: you'll kill it. 328 Main board; The Digital I/O Digital input/output terminal, a total of 0 ~ 13; The Analog I/O Analog input/output terminal, a total of 0 ~ 5; Support the ISP download function; Support the TX/RX terminals; Support the AREF terminals; Support the six groups of PWM terminal (Pin11 Pin10, Pin9, Pin6 and Pin5, responsible); The input voltage: 3.3 V DC; Using Atmel Atmega328V - 20 pu microcontroller; Specifications: Microcontroller: ATmega328V Operating Voltage: 2.7-5.5 V Input Voltage: 2.7-5.5 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 6 DC Current per I/O Pin: 40 mA Flash Memory: 16 KB (of which 2 KB used by bootloader) SRAM: 1 KB EEPROM: 512 bytes Clock Speed: 8 MHz Package includes: 1* LilyPad atmega 328 Main board Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Product Description ARM Core benefits The Due has a 32-bit ARM core that can outperform typical 8-bit microcontroller boards. The most significant differences are: A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. (for more information look  int type  page). CPU Clock at 84Mhz. 96 KBytes of SRAM. 512 KBytes of Flash memory for code. a DMA controller, that can relieve the CPU from doing memory intensive tasks. Pin Mapping:  SAM3X Pin Mapping page Product includes 1x arduino board 1x USB cable Summary Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Outputs Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Powered by Turbo Lister

Product Description ARM Core benefits The Due has a 32-bit ARM core that can outperform typical 8-bit microcontroller boards. The most significant differences are: A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. (for more information look  int type  page). CPU Clock at 84Mhz. 96 KBytes of SRAM. 512 KBytes of Flash memory for code. a DMA controller, that can relieve the CPU from doing memory intensive tasks. Product includes 1x arduino board 1x USB cable Summary Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 54 (of which 12 provide PWM output) Analog Input Pins 12 Analog Outputs Pins 2 (DAC) Total DC Output Current on all I/O lines 130 mA DC Current for 3.3V Pin 800 mA DC Current for 5V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB (two banks: 64KB and 32KB) Clock Speed 84 MHz Powered by Turbo Lister

The product is a brand new Arduino UNO R3 Clone. It has guilded pins for your use. Works on 5v USB or 6-12v dc power supply. Check http://arduino.cc/en/main/arduinoBoardUno for more details. Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g