Low development board ic

Universal Development Board for Arduino, , PIC, AVR and ARM7, Raspburry Pi   (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL       Product Overview   1.     About Digital and Analog IO Interfacing Board                                                                    If you are learning any microcontroller than input and output circuit is always important to experiment with any microcontroller. Digital and Analog IO Board is suitable for quick experiment with any microcontroller.   2.     Features Digital and Analog IO Interfacing Board having a following features:                                                               ·          Eight LEDs ·          Four Switches ·          One LDR (Light Dependent Resistor) (Light Sensor) ·          One Temperature Sensor (LM35) (Sensor) ·          One Variable Resistor (Preset/POT) (Sensor) ·          One Infrared receiver (TSOP) (Remote Control Sensor) ·          One Buzzer ·          One Relay Categories into Inputs/Outputs 1.        Digital Inputs ·          Switches ·          Infrared receiver (TSOP.        Analog Inputs ·          Variable Resistor ·          LDR ·          Temperature Sensor 3.       Digital and Analog Outputs ·          LEDs ·          Buzzer ·          Relay Dimensions (LxWxH) - Cms: 6.5 CM X 6.5CM Datasheet:  http://www.mediafire.com/view/6c3dmdhpw3rlwdh/Digital_and_Analog_IO_Board.pdf

The Freeduino is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Before connecting the Freeduino, CP Driver installation would be required.   Got to link below http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx Or google CP driver download. ------------àSelect as per your Operating system and download the driver------------àUnzip the file on desktop ------------àConnect the UNO with USB Cable given to your computer------------àDevice Manager will display Unknown device for the UNO (CP IC). Right click on the same and click on update driver. Give path as desktop. Wait till driver is installed. ------------àYour CP Driver is installed and Uno is ready for use.

Product Description:   The Freeduino is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Before connecting the Freeduino, CP2102 Driver installation would be required. Got to link below http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx Or google CP2102 driver download. ------------>Select as per your Operating system and download the driver------------>Unzip the file on desktop ------------>Connect the UNO with USB Cable given to your computer------------>Device Manager will display Unknown device for the UNO (CP2102 IC). Right click on the same and click on update driver. Give path as desktop. Wait till driver is installed.------------>Your CP2102 Driver is installed and Uno is ready for use.   Contact: Contact us on Messaging for any Queries. We offer discounts for bulk orders on   Feedback: We provide good quality products & all products are QC checked before dispatch. We strive for 100% positive feedback for our orders. Providing Negative feedback will not solve anything feel free to write to us on messaging service. Feel Free to contact us on +91 7738961235   Shipping: Shipping is done only through Powership. Logistics partners include – Bluedart DHL, Dotzot, Aramex, Fedex.  

Features Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled Arduino-like hardware IO Advanced API for hardware IO, which can dramatically reduce the redundant work for configuring and manipulating hardware. Code like arduino, but interactively

Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. INTRODUCTION   Serial to RS232 module by Positron allows you to convert TTL logic from your microcontroller to 232 logic levels. Using this module you can easily interface TTL logic GSMs, GPS and finger print sensor modules etc. with your microcontroller. This module can easily be used with Positron Development Boards.  SALIENT FEATURES This module has 4 pins viz. Receiver, Transmitter, Vcc and Ground These four pins can easily be connected to any of the Transmitter, Receiver, Vcc and Ground of a micro controller development board The module uses MAX232 IC and can be easily connected to your laptop using Positron’s DB9 cables

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

We offer a large selection of single channel to multi channel Relay Drivers for applications ranging from low power signal switching to high voltage, high current applications.  Quad channel relay controller we have a configuration to fit every need.  Quad channel relay can be controlled by feeding 2 to 5 V TTL from Micro-controller Development Boards, Remote Receivers, or any other circuit which required isolated high current and high voltage switching by applying TTL voltage.  LED indication for Relay On/Off, Relay Output normally open and normally close via screw terminal for easy connection.  Clamp diodes for current limiting for self protections.  Input via berg connector.  Board can control AC or DC load. Input supply 12 VDC @ 170 mA Output  four SPDT relay Relay specification 5 A @ 230 VAC Trigger level 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED on each channel indicates relay status Screw terminal connector for easy relay output and aux power connection Four mounting holes of 3.2 mm each PCB dimensions 88 mm x 68 mm DO IT YOUR SELF KIT (DIY) Kit contains components, PCB and Circuit Diagram

We offer a large selection of single channel to multi channel Relay Drivers for applications ranging from low power signal switching to high voltage, high current applications.  Dual channel relay controller we have a configuration to fit every need.  Dual channel relay can be controlled by feeding 2 to 5 V TTL from Micro-controller Development Boards, Remote Receivers, or any other circuit which required isolated high current and high voltage switching by applying TTL voltage.  LED indication for relay On/Off, Relay Output normally open and normally close is via screw terminal for easy connection.  Clamp diodes for current limiting for self protections.  Input via berg connector.  Board can control AC or DC load. Input supply 12 VDC @ 84 mA Output two SPDT relay Relay specification 5 A @ 230 VAC Trigger level 2 ~ 5 VDC Berg pins for connecting power and trigger voltage LED on each channel indicates relay status Screw terminal connector for easy relay output connection Four mounting holes of 3.2 mm each PCB dimensions 49 mm x 68 mm DO IT YOUR SELF KIT (DIY) Kit contains components, PCB and Circuit Diagram

Ad ID CityCoimbatore LocationSiddhapudur Category Elec tronics & Appliances >> Computer Peripherals Created On:Jul- Last Posted On:Jul- Ad Type:I Am Offering Peripheral Type:Other Ad Posted By:Individual Condition:New Price:Rs. Reserved TitleDE SKTOP AND LAPTOP SALES AND SERVICE DescriptionDesktop&Laptop (Sales & Service) Mother Board Chip Level Service On Calls & Amc Network Congification Data Backup & RECOVERY SOFTWARE DEVELOPMENT

1.      About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

9% Discount 31st March coupon code:  COUPONDUN9 1.     About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

FREE USB CABLE + & AVR USB ISP Programmer (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL     Product Overview   1.     About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

Meet the Espressif ESP32, a much-awaited sequel of the very popular ESP8266 SoC. This time around Espressif has given it a ton of integrated feature-rich peripherals. The CPU(s) is also upgraded with two individual cores from  Tensilica, each running at up to 240 MHz. Two because one takes care of the Wi-Fi and Bluetooth stacks' computational requirements and the other one dedicated for the application. This is just a lot of power waiting to be unleashed and still works on very low power for IoT applications. We are very excited with the capability of this chip and waiting to find more applications for it. At the time of writing this document, the support for ESP32 in Arduino is still kind of patchy, however Espressif has an excellent development toolchain based on the Xtensa toolchain for Tensilica controllers. We love using  Epressif's ESP-IDF toolchain and framework, it includes a great set of libraries. It works on Windows, MACOS and Linux. We use it on Ubuntu and it works like a charm. Note:  This product is still undergoing complete software testing for the various capabilities. Watch this page for more updates as we keep adding features in software for this. Note:  The Arduino core for ESP32 is still under development, so with the current state of the software, this board may not be a drop-in replacement for an Arduino. This feature should be available soon though. Features: On-board ESP32 System-On-Chip (SoC) featuring: Two   Tensilica  LX6 microcontroller cores running at 240 MHz, with 520 KB RAM !! Integrated Wi-Fi controller (802.11 b/g/n/i) up to 150 Mbps Integrated Dual-mode Bluetooth 4.2 controller ("classic" and Bluetooth low energy (BLE) support) 12-bit SAR 12-channel ADC 8-bit, 2-channel DAC Capacitive touch sensor interface LED PWM controller CAN 2.0 controller Integrated temperature sensor Integrated Hall-effect sensor  Operating temperature range: -40 C to +125 C 4 MB on-board FLASH memory On-board 2.4 GHz PCB trace antenna for Wi-Fi/Bluetooth On-board FTDI FT231X USB-UART converter Operation from single Li-Poly battery with on-board charger and regulator 2x capacitive touch switches 3x WS2812B addressable RGB LEDs Arduino Uno compatible form-factor for addition of shields Includes: 1x Kalam32-DEV board 1x 1500 mAH/3.7V Li-Ion battery 1x microUSB cable Documentation: Schematic (PDF) Schematics and code (Github) Tons of ESP32 related information at ESP32.com ESP32 IC Datasheet (PDF) Espressif ESP-IDF framework  (Recommended) Complete user guide (coming soon)

Product Description This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector. The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target. This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working. This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector. One of the nice features of this board is a jumper on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level). This board ship default to 5V, but you can cut the default trace and add a solder jumper if you need to switch to 3.3V. Powered by Turbo Lister

DESCRIPTION RC522 is the high integrated RFID card reader which works on non-contact MHz communication, is designed by NXP as a low power consumption, low cost and compact size read and write chip, is the best choice in the development of smart meters and portable hand-held devices. MF RC522 use the advanced modulation system, fully integrated at MHz with all kinds of postive non-contact communication protocols. Support A compatible answer signal. DSP deal with ISOA frames and error correction. Futhermore, it also supports rapid CRYPTO1 encryption to validate Mifare series products. MFRC522 support Mifare series higher speed non-contact communication, duplex communication speed up to 424 kb/s. As a new family member in MHz RFID family, MF RC522 has many similarities to MF RC and MF RC530, and also has more new features. This module can fit directly in hand held devices for mass production. Module use 3.3V power supply, and can communicate directly with any CPU board by connecting through SPI protocol, which ensure reliable work, high reading distance. Specification: Working current mA / DC 3.3V Standby current mA / DC 3.3V Sleep current Peak current Working frequency MHz Card reading distance 0 30mm Mifare1 card Protocol SPI Data communication speed 10Mbit/s Max. Dimension 40mm 60mm Working temperature - degree Storage temperature - degree Humidity relevant humidity 5% 95% We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

We offer a large selection of single channel to multi-channel Relay Drivers for applications ranging from low power signal switching to high voltage, high current applications.  Quad channel relay controller we have a configuration to fit every need.  Quad channel relay can be controlled by feeding 2 to 5 V TTL from Micro-controller Development Boards, Remote Receivers, or any other circuit which required isolated high current and high voltage switching by applying TTL voltage.  LED indication for Relay On/Off, Relay Output normally open and normally close via screw terminal for easy connection.  Clamp diodes for current limiting for self-protections.  Input via berg connector.  Board can control AC or DC load.       Input supply 12 VDC @ 170 mA     Output four SPDT relay     Relay specification 5 A @ 230 VAC     Trigger level 2 ~ 5 VDC     Berg pins for connecting power and trigger voltage     LED on each channel indicates relay status     Screw terminal connector for easy relay output and aux power connection     Four mounting holes of 3.2 mm each