Motor driver control

Motor driver, ultrasonic distance sensor Bread board, water flow sensor measure LED display, IR sensor etc. At reduced cost not using that's why selling anyone can also buy any of them

Product Description The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. Features: Driver: L298N Dual H Bridge DC Motor Driver IC   Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V   Driven part of the peak current Io: 2A   The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)   The logical part of the operating current range: 0 ~ 36mA   Storage temperature: -25 Deg C ~ +130 Deg C   Other Extensions: control of direction indicators, the logic part of the plate to take power interface.Driver Board Size: 55mm * 60mm * 30mm   Drive plate Weight: 33g   Other Function: Control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.

The DRV stepper motor driver carrier is a breakout board for TI’s DRV microstepping bipolar stepper motor driver. The DRV features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from  V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling). This product is a carrier board or breakout board for TI’s DRV stepper motor driver; we therefore recommend careful reading of the DRV datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features: Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45 V maximum supply voltage Built-in regulator (no external logic voltage supply needed) Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer, 2 oz copper PCB for improved heat dissipation Exposed solderable ground pad below the driver IC on the bottom of the PCB This product ships with all surface-mount components—including the DRV driver IC—installed as shown

DC Motor / Stepper Driver H Bridge Controller This motor driver is perfect for robotics and mechatronics projects for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms, etc. This is a medium power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L293 motor driver IC. It can drive 4 DC motors on and off, or drive 2 DC motors with directional and speed control. The driver greatly simplifies and increases the ease with which you may control motors, relays, etc from microcontrollers. It can drive motors upto 36V with a total DC current of up to 600mA. You can connect the two channels

DC Motor / Stepper Driver H Bridge Controller This motor driver is perfect for robotics and mechatronics projects and perfect for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms, etc This is a high power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L298 motor driver IC and has onboard 5V regulator which it can supply to an external circuit. It can control upto 4 DC motors, or 2 DC motors with directional and speed control It can drive motors upto 46V with a total DC current of up to 4A. You can connect the two channels

Easy Driver Stepmotor Description EasyDriver Shield stepping Stepper Motor Driver V44   Description  • The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). It requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. It provides much more flexibility and control over your stepper motor, when compared to older versions. The microstep select (MS1 and MS2) pins of the A are broken out allowing adjustments to the microstepping resolution.. Features • Compatible with 4, 6, and 8 wire stepper motors of any voltage  • Adjustable current control from 150mA/phase to 750mA/phase  • MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth)  • Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds Package Info 1 X PC Easy Step Driver Shield with pins. Feedback Info We Provide Optimum Quality and Fast Shipping which is self explanatory by Review others have given us please have look if you have any question of doubt. Our Prices are the Cheapest on E-bay, If you find any of our item Selling at cheaper price then Message us the details and we would provide you at same price. For providing such services many individuals and department of ours are working very hard  24hr X 7 X 365 days, and we look for token of appreciation for all this by providing us with positive feedback. For Any Technical Assistance and Guidance Please Post on Our Forum www.sonishop.com/forum We would get back to you for same.

Easy Driver Stepmotor Description EasyDriver Shield stepping Stepper Motor Driver V44   Description  • The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). It requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. It provides much more flexibility and control over your stepper motor, when compared to older versions. The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution.. Features • Compatible with 4, 6, and 8 wire stepper motors of any voltage  • Adjustable current control from 150mA/phase to 750mA/phase  • MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth)  • Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds Package Info 1 X PC Easy Step Driver Shield with pins. Feedback Info We Provide Optimum Quality and Fast Shipping which is self explanatory by Review others have given us please have look if you have any question of doubt. Our Prices are the Cheapest on E-bay, If you find any of our item Selling at cheaper price then Message us the details and we would provide you at same price. For providing such services many individuals and department of ours are working very hard  24hr X 7 X 365 days, and we look for token of appreciation for all this by providing us with positive feedback. For Any Technical Assistance and Guidance Please Post on Our Forum www.sonishop.com/forum We would get back to you for same.

PCA Channel 12-bit PWM Servo motor Driver I2C Module Arduino PIC Robot WC You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs • It's an i2c-controlled PWM driver with a built

PCA9685 16 Channel 12-bit PWM Servo motor Driver I2C Module Arduino PIC Robot WC You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs • It's an i2c-controlled PWM driver with a built

Special Scheme BUY 4 GET 1 FREE The All new Motor Driver Shield for your Arduino. It can run 2 servo or 2 stepper or 4 DC motor with the help of external power supply and controlling via arduino. Versatile product comes from adafruit. --  2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution      dedicated timer - no jitter! --  Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%      resolution) --  Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or      micro-stepping. --  4 H-Bridges: L293D chip set provides 0.6A per bridge (1.2A peak) with thermal shutdown      protection, 4.5V to 25V --  Pull down resistors keep motors disabled during power-up --  Big terminal block connectors to easily hook up wires (AWG) and power --  Arduino reset button brought up top --  2-pin terminal block to connect external power, for separate logic/motor supplies --  Tested compatible with Mega, Diecimila, & Duemilanove now, first time Made

L293D DUAL H-BRIDGE MOTOR DRIVER About  L293D IC generally comes as a standard 16-pin DIP (dual-in line package). This motor driver IC can simultaneously control two small motors

CNC Stepper Motor Driver 3 Axis TB Stepper Motor Driver Controller       TB Axis CNC Stepper Motor Driver 3 Axis TB Stepper Motor Driver Controller Description: This 3 axis stepper motor driver controller board adopts high-powered professional controller chip TB, making microcomputer applies controller function to driver board to form the smallest controller system

THIS L293D DRIVER MODULE IS A MEDIUM POWER MOTOR DRIVER PERFECT FOR DRIVING DC MOTORS AND STEPPER MOTORS. IT USES THE POPULAR L293D MOTOR DRIVER IC. IT CAN DRIVE 4 DC MOTORS IN ONE DIRECTION, OR DRIVE 2 DC MOTORS IN BOTH THE DIRECTIONS. FEATURES AND USAGE L293D motor driver IC. Male burg stick connectors for supply, ground and input connection Screw terminal connectors for easy motor connection This motor driver is perfect for robotics and mechatronics projects for controlling motors from microcontroller, switches, relays, etc. Perfect for driving DC and Stepper motors for micromouse, line following robots, robot arms

This is spare parts for making voice control car is fully in working condition. 1. Arduino Uno board 2. HC-05 Bluetooth module 3. L298 2A dual motor driver 4. Bo-motor 100 rpm (x4) 4 pieces 5. Wheel (x4) 4 pieces Price for combo = 1100 Rs/- (negotiable) Also you can buy it separately. Contact : Insta I'd - ( its_shanky_306) dm me

High Ampere Dual Motor Driver H-Bridge Module   Package includes: §   1 x High ampere (4A) Dual Motor Driver module   Description: §   The motor driver module is based on MOSFETs (Metal Oxide Semiconductor Field Effect Transistor) and power transistors delivering current up to 5A (max current). §   The module has 4 inputs: “ IN A ”, “ IN B ”, “ IN C ”, “ IN D ”. §   The working logic is given below:   IN A IN B Direction 0 0 Brake 0 1 CW 1 0 CCW 1 1 Brake