Quadcopter controller board

KKmulticopter V5.5 controller blackboard Quadcopter + USB Programmer + Signal Distribution Board Description: The KKmulticopter is a KK flight controller board for remote control multicopters with 2,3,4 and 6 rotors. We get KKmulticopter to stablise the aircraft during flight. KK flight controller takes the signal from the three gyros on the board (roll, pitch and yaw) and feeds the information into the Integrated Circuit (Atmega IC). KK flight controller then processes the information according the the KK software and sends out control signal to the Electronic Speed Controllers (ESCs) which are plugged onto the board and also connected to the motors. Depending the signal from the IC the ESCs will either speed up or slow down the motors (and tilt the rear rotor with a servo

Rev AF WD Controller Board My Book Essential 1TB/2TB/3TB USB 3.0 Description: Western Digital My Book Essential USB 3.0 This board is compatible with 1TB, 2TB & 3TB Hard Drives Controller board supports the following Part number: WDBACWHBK, WDBACWHBK & WDBACWHBK REV P1 on the PCB Quantity: 1pcs Item condition: Pulled from new device! 99% of new,GOOD PRICE FAST SHIPPING!!!! Tested 100% work! Important note: If you hard disk have some problem or bad, It can't recover any data! Please see all details and shipping policy before purchase.Thanks! Details No hard drive included

Rev AA WD Controller Board My Book Essential 1TB/2TB/3TB USB 2.0 Description: Western Digital My Book Essential USB 2.0 This board is compatible with 1TB, 2TB & 3TB Hard Drives WD My Book Essential External Hard Drive Control Board Part No: PCB REV. AA (Printed on white sticker) Part No: PCB REV. P1(Printed on the circuit board) Support 20GB ~ 500GB 1TB, 1.5TB, 2TB of 3.5" SATA HDD to USB 2.0 Quantity: 1pcs Item condition: Pulled from new device! 99% of new,GOOD PRICE FAST SHIPPING!!!! Tested 100% work! Important note: If you hard disk have some problem or bad, It can't recover any data! Please see all details and shipping policy before purchase.Thanks! Details No hard drive included

n Unipolar 4-Phase Stepper Motor Controller Board will help you control a Stepper Motor or 4 individual Solenoids. Box Header (IDC) connector provides for easy interfacing option Separate LED indicator for individual Phase Screw terminal connector for easy connection of output load and power supply input Power-On LED indicator Four mounting holes of 3.2 mm each PCB dimensions 86 mm x 49 mm

DESCRIPTION Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for Arduino 1. L298N as main chip, ST corporation production. 2. Low heat,outstanding anti-interference performance. 3. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power 25w. 4. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. 5. Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply. 6. Large capacity filter capacitance,afterflow protection diode, more stable and reliable. o Specifications: 2. Double H bridge drive 3. Chip: L298N (ST NEW) 4. Logical voltage: 5V 5. Drive voltage: 5V-35V 6. Logical current: 0mA-36mA 7. Drive current: 2A(MAX single bridge) 8. Size:43 x 43 x 26mm 9. Max power: 25W 10. Net weight: 25g Uses: 11. Driving stepper motor: The connection of driving a common 4 line 2 phase electric motor is shown in figure after enable ENA ENB Input the following driving timing from IN1-IN4-then the speed and direction of the stepper motor can be controlled. 12. Driving DC motor: Because this module is driven by double H bridge,it can drive two motors simultaneously. after enable ENA ENB You can input the speed and direction of PWM signal drive motor 1 from IN1 IN2 You can input the speed and direction of PWM signal drive motor 2 from IN1 IN2 We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers. The APM 2.8 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors. This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility

Description L298N is a kind of high voltage, high current motor driver chip produced by ST company. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V), large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on. Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well. Features： Using L298N made by ST company as the control chip,the module has such characteristics as strong driving  ability, low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage  of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability Specification Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logical current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Size:mm Applied cases: 1) Driving stepper motor The connection of driving a common 4 line 2 phase electric motor is shown

Description The ArduPilot Mega 2.6 allows the user to turn any fixed, rotary wing or multirotor vehicle (especially multicopters and rovers) into a fully autonomous vehicle;capable of performing programmed GPS missions with waypoints1. 3.3V or 5.0V DC power supply 1. Arduino and ArduPilot Mega 2.5 Compatible! 2. Includes both right angle and straight pins for I/O, allowing user to customize as needed. 3, Onboard 4 MP Dataflash chip for automatic datalogging 4. Invensense/'s 6 DoF Accelerometer/Gyro MPU-6000. 5. Atmel/'s ATMEGA2560-16AU and ATMEGA32U-2 chips for processing and usb functions respectively. 6. Barometric pressure sensor upgraded to MS5611-01BA03, from measurement specialties Note1: The Power Module is only designed to power APM, a RC receiver and APM accessories (GPS, Telemetry radio). It is not designed to power servos. Use your aircraft/'s own ESC/BEC for that. Note2: the use of electric power transfer: the need to JP1 jumper plug, power supply voltage does not exceed 5.6V, not less than five using UEBC: The UEBC power output cable plugged into the receiver INPUTS port, power supply is not higher than 5.2 is not lower than 4.8V Technical parameters:   Material: Plastic, Copper Main Color: Black Size: 70*44*13 mm Net weight: 38g Color: As shown

New Improved Remote Controller Board Kit For Wireless Robot - 433 Mhz Rx Tx (Ideal for Robotic Vehicle) with power supply circuit Features/Specification  1.Power Supply to Transmitter Board - 9V (Battery Free) 2.Power Supply to Receiver Board -12V (Battery not Included) 3.Easy Interface with microcontroller (If required) 4.Comes with DPDT Relay Board to control 2 DC Motors(upto-4, if connected 2 left and 2 right side motor

The Arduino Uno is a micro controller board based on the ATmega328. Summary Micro controller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

F450 quadcopter 4 axis strong frame Comes With Multicolour The Glass Frame Build With Top quality Fiberglass F450 quadcopter Frame has Large camera Mounting holder For camera mount, easy install And Remove also built in Power Distribution Board F450 Quadcopter Frame,F450 Drone Frame, Buy link Is Here https://robotbanao.com/products/f450-quadcopter-4-axis-strong-frame-multicolour

F450 quadcopter 4 axis strong frame Comes With Multicolour The Glass Frame Build With Top quality Fibreglass F450 quadcopter Frame has Large camera Mounting holder For camera mount, easy install And Remove also built in Power Distribution Board and more info ROBOTBANAO.com

Almost ready to fly Quadcopter450 kit without Battery. ITEMS INCLUDED: 1. APM2.6 flight controller. 2. Nylon polymide Frame with integrated Power Distb Board(450mm) 3. 30 Amps ESCs KV brushless DC motors 650gms thrust polymer propellers. 6. Avionic 2.4Ghz 6ch transmitter and reciever. 7. Ublox GPS with built in Compass. 8. Suitable connectors and wires.

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Sensor Shield v5.0 expansion board for arduino electronic building blocks robot accessories Sensor Shield V5 expansion board Latest Sensor Shield V5.0 sensor expansion board to retain the advantages of version V4.0 on the basis of still only stack design, PCBImmersion Gold processing technology, the motherboard is not only the Duemilanove 2009 controller digital and analog interfacesequenceform of steering gear line extension, but also ad hoc IIC interface 32 servo controller Interface Bluetooth module communication interface, SD card module communication interface, the APC220 wireless RF module communication interface, the RB The URF v1.1 ultrasonic sensor interface12864serial and parallel interfaces, independent expansion of a more easy-to-use convenience. For beginners, you do not have a headache forthe cumbersome and complex circuit connection, the sensor extends the true sense of the board to simplify the circuit can easily connect thecommonly used sensor, a sensor requires only a common 3P the sensor cable (regardless of digital cable and analog cable), after the completion ofthe circuit connection, the preparation of the corresponding program downloaded to the Duemilanove controller reads the sensor data, or receive wireless module to return data after computing the final easy to complete your own interactive works. Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged