Sfp module s

S-31DLC20D is a 1.25G SFP transceiver with a nm Dual LC connector, for up to 20 kilometer Single Mode fiber connections, with DDM Units are tested and compatible with RB260GS,RBLS, RBLS-IN, RBUAS-IN, RBUAS-RM, RBUAS-2HnD, RBUAS-2HnD-IN, and CCRG-4S. Units are compatible with non-MikroTik SFP devices as well.

S-85DLC05D is a 1.25G SFP transceiver with a 850nm Dual LC connector, for up to 550 meter Multi Mode fiber connection, with DDM. Units are tested and compatible with RB260GS, RBLS, RBLS-IN, RBUAS-IN, RBUAS-RM, RBUAS-2HnD, RBUAS-2HnD-IN and CCRG-4S. Units are compatible with non-MikroTik SFP devices as well.

We deals in Cisco products like Sfp modules and Line cards or Dac cables if anybody have products so please tell me we purchase best price over all market . Thanks.

We are buying cisco SFP module and line card like ASR 9000 Series and many more Deal brand like cisco juniper ciena

Product Description This is a wifi solution based on IC ESP from Espressif, very price competitive wifi module, and also great function. Bring your project to the internet of things easily! Features: Very competitive price AP, STA, AP+STA modes available. Very simple AT commands, easy to use. internal LWIP interface. Only four pins interface, VCC-3V3, GND, TXD and RXD. Current firmware V091 for all stock, new reserved reset and CH_PD (for updating) pins available, you can refresh the firmware now. All using new ESPex new chip, old chip is not available anymore. Pin description Pin High Status Low Status Note VCC, GND Use standalone power source, or large capacitor, all power of this module from external TXD, RXD The serial port RST - restart CH_PD Flash boot and Update Mode - chip enable, so always connect to high status with VCC GPIO0 - Update mode GPIO2 - - GPIO 15 (when avaialble) NC Flash boot Mode Only for a few version, Wi07-3 GPIO 12 GPIO 13 GPIO 14 GPIO 16 Hardware RST No need any pull-up AT commands §   Baud rate: (from v0.90, v0.80 and older: ) §   The AT part of the command can be written large or small, however, the following command must always be written large §   Make sure that before, after and within the command no spaces (space) occur General AT commands AT command Description Parameter Example AT Test command, are always "OK" back AT AT + RST Reset of the module, the module's boot messages followed by  ready  back AT + RST AT + GMR Querying the Firmware Version AT + GMR WiFi AT commands AT command Description Parameter Example AT + CWMODE =  Setting the WiFi mode  1) Station 1 =  2 = Access Point  3 = Both AT + CWMODE = 1 AT + CWMODE? Query WiFi mode AT + CWMODE? AT + CWMODE =? Query of possible settings for WiFi mode AT + CWMODE =? AT + CIPMUX = Using multiple connections 0 = single compound  1 = Multiple connections AT + CIPMUX = 1 AT + CIPMODE = Setting the data mode 0 = transparent  1 = Data AT + CIPMODE = 1 AT + CIPMODE? Output of the data set mode AT + CIPMODE? WiFi commands (Station / client) AT command Description Parameter Example AT + CWJAP =, Connecting to WiFi network ssid "SSID"  pass "password" AT + CWJAP = "makerday", "M4k3rd4y" AT + CWJAP? Output of the currently connected WiFi network AT + CWJAP? AT + CWLAP Output of available APs  2) AT + CWLAP AT + CWQAP Closes the connection to an access point AT + CWQAP AT + CIFSR Issue its own IP address AT + CIFSR WiFi commands (Access Point) AT command Description Parameter Example AT + CWSAP =, [,,] Set the access point parameters  3) ssid "SSID"  pass "password"  chan "channel"  enc "Encryption"  (0 = Open  1 = WEP  WPA_PSK 2 =  3 = WPA2_PSK  4 = WPA_WPA2_PSK) AT + CWSAP = "makerday", "M4k3rd4y" 5.3 AT + CWSAP? Output the current settings for the AP AT + CWSAP? AT + CWLIF Lists stations connected IPs 4) AT + CWLIF WiFi commands (IP Client) AT command Description Parameter Example AT + CIPSTATUS Output status of the IP connection (s) AT + CIPSTATUS AT + CIPSTART =,, Creating an IP connection with AT + CIPMUX = 0 type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND = Sending data over a single compound  5) len: Data length AT + CIPSEND = AT + CIPCLOSE Close a single TCP or UDP connection AT + CIPCLOSE AT + CIPSTART =,,, Creating an IP connection with AT + CIPMUX = 1 id: 0-4  type: "TCP" or "UDP"  address "IP address"  port: TCP / UDP port AT + CIPSTART = "TCP", " AT + CIPSEND =, Send data via merhere compounds 6) id: 0-4  len: Data length AT + CIPSEND = AT + CIPCLOSE = Close one of several TCP or UDP connection id: 0-4 AT + CIPCLOSE = 1 WiFi commands (IP server) AT command Description Parameter Example AT + CIPSERVER = 1 [,] Starts the TCP server port: TCP port AT + CIPSERVER = AT + CIPSERVER = 0 Terminates the TCP server AT + CIPSERVER = 0 AT + CIPSTO = Sets timeout for TCP server timeout = s AT + CIPSTO = 180 AT + CIPSTO? Specifies timeout of TCP server AT + CIPSTO? If a TCP server is started, it can handle up to 5 simultaneous connections. Other compounds can be created, but only served when others are closed or terminated by timeout. The module incoming data directly with the prefix  + IPD  issued: + IPD,   OK   + IPD, 0.6: ON   OK The output is divided as follows: + IPD,,, It is  id  the ID of the compound (0-5),  len  the length of the resulting data packet and  data  contains the data received from the client. In the above example as first sends compound 1 the value   and then connect the string 0  ON     Powered by Turbo Lister

Module  has been designed around Win bond’s ISD IC (SMD) IC, which is fully integrated, single-chip, single message voice record and playback device ideally project suited to a variety of electronics systems. Messages are stored

Module has been designed around Winbond’s ISD IC (SMD), which is a fully integrated, single-chip, single message voice record and playback device, ideally suited to a variety of electronics systems, Message duration is user selectable

Brand new product (not used) This item works with L2 switch only The Cisco 10GBASE-SR Module supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade multimode fiber (MMF). Using 2000MHz*km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz*km MMF (OM4), up to 400m link lengths are possible.

USED Cisco WS-CG-24PS-S Switch TESTED IN EXCELLENT CONDITION   Catalyst G 24POE SFP;1RU Product Condition used Included Items 1 X Cisco WS-CG-24PS-S 1U Switch       PRODUCT INCLUDES RACK MOUNT KIT  CONSOLE AND POWER CORD CONTACT ME ON   or

We are buying cisco SP module and line card like ASR 9000 Series and many more Deal brand like cisco juniper ciena Nokia

We are buying cisco SP module and line card like ASR 9000 Series and many more Deal brand like cisco juniper ciena

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description The Compass Module 3-Axis HMCL is a low-field magnetic sensing device with a digital interface. The compass module converts any magnetic field to a differential voltage output on 3 axes. This voltage shift is the raw digital output value, which can then be used to calculate headings or sense magnetic fields coming from different directions. The module is designed for use with a large variety of microcontrollers with different voltage requirements. 3-Axis magneto-resistive sensor   1 to 2 degree compass heading accuracy Wide magnetic field range (+/-8 gauss) Fast 160 Hz maximum output rate Precision in-axis sensitivity and linearity Measures Earth’s magnetic field, from milli-gauss to 8 gauss The HMCL utilizes Honeywell's Anisotropic Magneto resistive (AMR) technology that provides advantages over other magnetic sensor technologies. These anisotropic, directional sensors feature precision in-axis sensitivity and linearity. These sensors' solid-state construction with very low cross-axis sensitivity is designed to measure both the direction and the magnitude of Earth's magnetic fields, from milli-gauss to 8 gauss. Honeywell's Magnetic Sensors are among the most sensitive and reliable low-field sensors

  Description The Compass Module 3-Axis HMC5883L is a low-field magnetic sensing device with a digital interface. The compass module converts any magnetic field to a differential voltage output on 3 axes. This voltage shift is the raw digital output value, which can then be used to calculate headings or sense magnetic fields coming from different directions. The module is designed for use with a large variety of microcontrollers with different voltage requirements. 3-Axis magneto-resistive sensor   1 to 2 degree compass heading accuracy Wide magnetic field range (+/-8 gauss) Fast 160 Hz maximum output rate Precision in-axis sensitivity and linearity Measures Earth’s magnetic field, from milli-gauss to 8 gauss The HMC5883L utilizes Honeywell's Anisotropic Magneto resistive (AMR) technology that provides advantages over other magnetic sensor technologies. These anisotropic, directional sensors feature precision in-axis sensitivity and linearity. These sensors' solid-state construction with very low cross-axis sensitivity is designed to measure both the direction and the magnitude of Earth's magnetic fields, from milli-gauss to 8 gauss. Honeywell's Magnetic Sensors are among the most sensitive and reliable low-field sensors

WELCOME TO ROBOCENTRAL***    ***IMPORTED  GY-521 MPU- Module 3 Axis Gyroscope + Accelerometer for Arduino   ***             ! !   YOU WILL GET SAME PRODUCT AS SHOWN IN THE PICTURE! ! !!!Description!!! MPU- module (Three Axis Gyro + Three Axis Acceleration) Chip used: MPU-  Power supply: 3-5 v (internal low voltage difference voltage stabilizing)  Communication: standard IIC communication agreement  Chip In-built 16 bit AD converter, 16 bits of data output  The gyroscope range: + degree /sec  Acceleration range: ± 2g ± 4g ± 8g ± 16 g  Net weight:3 g  Package weight:13 g  The MPU- is a high precision piece of motion processing tech. By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an on board Digital Motion Processor™ (DMP™) capable of processing complex 9-axis Motion Fusion algorithms MPU- does away with the cross-axis alignment problems that can creep up on discrete parts. Auxiliary master I2C bus which allows the MPU- to access external magnetometers and other sensors. Note: V oltage rating should not exceed V. Package Contains                                                                               1 X   MPU- Module                                                            2 x sets of header pins        we value your needs           So usually ship within same business day except Sunday or public holiday's          WE AIM AT PROVIDING BEST QUALITY PRODUCT S                    ***AT LOWEST POSSIBLE RATES ***                      * **WE  USE QUALITY SHIPPING ONLY***           (TO ENSURE THAT THE PRODUCT REACHES YOU AT THE EARLIEST)         YOUR FEEDBACK IS HIGHLY VALUABLE FOR OUR BUSINESS TO GROW   **PLEASE LEAVE US THE BEST 5(STAR) RATINGS**      *********ONCE YOUR ARE SATISFIED*********   In case of any claim or complaints please contact us before leaving any neutral or negative feedback    ****And we will try our best to resolve your issue****    For Any Queries Please Call us on: / .   OR    You can email us at:            "DON'T WORRY BUY WITH CONFIDENCE"        !!!THANK'S FOR  GIVING US YOUR VALUABLE TIME!!!            **PLEASE VISIT AGAIN**