Ss module display

OV CMOS Camera Module Display Active Size 640X480 SCCB Compatible I2C for Ardunio OV image sensor, small volume, low operating voltage, providing all functions of a single chip of VGA camera and image processor. Through SCCB bus control, the sensor can output the whole frame, sampling, and various resolution 8 bits of data. Users can completely control the image quality, data format and transmission mode. All the process of image processing functions can be through the SCCB programming interface, including gamma curve, white balance, saturation and chroma. Image sensor has been

Feature ERMSYG-6 is lcd module ks, RoHS, -20°C to +70°C 6:00, Neg Voltage Generator,Parallel and Serial Interface,ST Controller,Popular Size Attribute Gross Weight (kg) Manufacturer EastRising Series Number ERM Part Number(Order Number) ERMSYG-6 Connection Pin Header Display Format 128x64 Dots Sunlight Readable Yes Touch Panel Optional No Outline Dimension 93.0(W)x70.0(H)x12.5(T)mm Visual Area xmm Active Area (W)x(H) Character Size No Diagonal Size 2.9” Dot (Pixel) Size 0.48x0.48mm Dot Pitch 0.52x0.52mm IC Package COB IC or Equivalent ST Interface -bit Parallel, -bit Parallel, 3-Wire Serial SPI Display Type STN-LCD Yellow Green Response Time(Typ) No Contrast Ratio(Typ) No Colors No Viewing Direction 6:00 Viewing Angle Range No Appearance Dark Blue on Yellow Green Brightness(Typ) No Backlight Color Yellow Green Color Backlight Current (Typ) 60mA Power Supply(Typ) 3.3V Supply Current for LCM(Max) 6mA Operating Temperature -℃ Storage Temperature -℃

OLED 0.96" I2C IIC SPI Serial 128X64 WHITE Display LCD LED Module for Arduino What is OLED? OLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel displays. The use of OLED technology offers the following advantages for flat-panel displays? 1. A simplified manufacturing process compared to TFT-LCD (See comparison of Picture 1 and Picture 2 below) 2. Self-emitting light, in contrast to the required backlight for TFT-LCD 3. High luminosity 4. Lightweight and thin (less than 2 mm) 5. Capable of wide viewing angles?~180?? 6. Low operating voltage and power consumption 7. Quick response (~ ? second level) 8. Wide range of operating temperatures (-40c to 85c) A Comparison of OLED and TFT-LCD Display Technologies How Does OLED Emit Light? OLED"s basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electroluminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components. Interface: VCC: 3.3-5V GND: Ground SCL: Serial Clock SDA: Serial Data Needn't backlight, the display unit can self-luminous High resolution: 128 * 64 Viewing angle:> 160 ° Supports many control chip: Fully compatible with Arduino, 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc. Ultra-low power consumption: full screen lit 0.08W Voltage: 3V ~ 5V DC Working Temperature: -30 c ~ 70 c Module Size:  27.3MM *27.8MM I2C/IIC Interface, need 2 IO only. Driver IC: SSD1306     Note: This item come I2C/IIC interface only. Because the hardware reasons, resulting IIC/I2C bus no ACK response signal, so IIC IIC communication Whitby automated production of OLED modules instead of the standard version. But this can be solved by software...... published here for the Arduino library file, you can make this OLED module used in the Arduino system. Download File description:- IIC_without_ACK.cpp - SSD1306 drivers; IIC_without_ACK.h - SSD1306 driver file header; oledfont.c - matrix table (you need to display the contents of the matrix can be calculated by taking the modulus of software after adding this file, modulo the way " common cathode - out line - Reverse Output"; font will take up a lot of space FLASH, please comment out the unwanted font, so there will be enough space Arduino tips). Function:- Write_IIC_Byte (unsigned char IIC_Byte); / / by IIC write an 8-bit data (such as 0xff) Write_IIC_Command (unsigned char IIC_Command); / / write command to the OLED module through IIC bus Begin_IIC_Data (); / / write data through the IIC bus open ready (which would allow a group of data transmission is complete and then turn off IIC, can greatly speed) IIC_SetPos (unsigned char x, unsigned char y); / / Set the starting point coordinates (x range 0 ~ 128, y ranges from 0 to 7) Fill_Screen (unsigned char fill_Data); / / Fill_Screen (0xff) - Full screen lit; Fill_Screen (0 × 00) - Full screen off (can be used to clear the screen) Char_F6x8 (unsigned char x, unsigned char y, const char ch []); / / display the ASCII character 6 × 8 Char_F8x16 (unsigned char x, unsigned char y, const char ch []);/ / display the ASCII character 8 × 16 CN_F16x16 (unsigned char x, unsigned char y, unsigned char N); / / display of 16 × 16 characters (this can be considered for the first time on the Arduino platform to achieve the display of Chinese characters) Draw_BMP (unsigned char x0, unsigned char y0, unsigned char x1, unsigned char y1, const char BMP []); / / display BMP images of 128 × 64 The other functions is functional function. Usage: Please "IIC_without_ACK" folder to x: / arduino-1.5.5 / libraries directory, restart the Arduino IDE; Demo_IIC is based on the Arduino UNO sample program...... correct wiring and run.   Package Included: 1PCS * New  white 0.96" I2C IIC SPI Serial 128X64 OLED LCD LED Display Module for Arduino Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Nokia LCD Module Nokia LCD Module This is a low-cost monochrome LCD module comprised of 84x48 pixels that can be used to display rich graphic and text content. Though it’s an industrial module, this LCD display is extremely easy to use. This module is a revision that accepts 3-5V input. So no extra level shifter is needed. To have full control, you just need 5 pins. And as a classic display module among open source communities, there are handful related tutorials available over the Internet. So there is no need to panic even if you just got your foot

Blue 0.96" inch SPI 128 x 64 OLED display module with CS pin SSD   Fully working Software Code included with English Font.     Description:   What is OLED? OLED   (Organic Light-Emitting Diode) is a self light-emitting technology   composed of a thin, multi-layered organic film placed between an anode   and cathode. In contrast to LCD technology, OLED does not require a   backlight. OLED possesses high application potential for virtually all   types of displays and is regarded as the ultimate technology for the   next generation of flat-panel displays.   How Does OLED Emit Light? OLEDs basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electroluminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components.   Features: Interface: IIC/4-Wire SPI Visual Angle: >160° No backlight needed, the display OLED are self-luminous Fully compatible with arduino, AVR, PIC, 51 series, MSP,STM,CSR or any controller with SPI. Wide range of operating temperature: -30°C to 70°C Easy to use software code due to low pin count Specifications: Display Colour: Blue Input Voltage: 3.3V ~ 6V Compatible I/O Level: 3.3V, 5V Dot Matrix:    128 x 64 Module Size:27.0mm x 27.0mm x 4.0mm Applications: Mobile Display Medical instrumentation Gaming and devices Industrial instrumentation Personal navigation devices   Package Include: ·       1 x   0.96” OLED Display Module ·       A plastic container box ·       Software Code (Zip file e-Mail)   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·        In case you find any problem

Blue 1.3" inch SPI 128 x 64 OLED display module with CS pin   Fully working Software Code included with English Font   Description:   What is OLED? OLED   (Organic Light-Emitting Diode) is a self light-emitting technology   composed of a thin, multi-layered organic film placed between an anode   and cathode. In contrast to LCD technology, OLED does not require a   backlight. OLED possesses high application potential for virtually all   types of displays and is regarded as the ultimate technology for the   next generation of flat-panel displays.   How Does OLED Emit Light? OLEDs basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electroluminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components.   Features: Interface: IIC/4-Wire SPI Visual Angle: >160° No backlight needed, the display OLED are self-luminous Fully compatible with Arduino, AVR, PIC, 51 series, MSP, STM, CSR or any controller with SPI. Wide range of operating temperature: -30°C to 70°C Easy to use software code due to low pin count Specifications: Display Colour: Blue Input Voltage: 3.3V ~ 6V Compatible I/O Level: 3.3V, 5V Dot Matrix:128 x 64 Module Size:35.5mm x 33.5mm x 4.0mm Applications: Mobile Display Medical instrumentation Gaming and devices Industrial instrumentation Personal navigation devices   Package Include:   ·       1 x   1.3” OLED Display Module ·       A plastic container box ·       Software Code (Zip file e-Mail)   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·        In case you find any problem

OLED 0.96" yellow blue Display Module For Arduino I2C Display 128X64 OLED What is OLED? OLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel displays. The use of OLED technology offers the following advantages for flat-panel displays? 1. A simplified manufacturing process compared to TFT-LCD (See comparison of Picture 1 and Picture 2 below) 2. Self-emitting light, in contrast to the required backlight for TFT-LCD 3. High luminosity 4. Lightweight and thin (less than 2 mm) 5. Capable of wide viewing angles?~180?? 6. Low operating voltage and power consumption 7. Quick response (~ ? second level) 8. Wide range of operating temperatures (-40c to 85c) A Comparison of OLED and TFT-LCD Display Technologies How Does OLED Emit Light? OLED"s basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electroluminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components. Interface: VCC: 3.3-5V GND: Ground SCL: Serial Clock SDA: Serial Data Needn't backlight, the display unit can self-luminous High resolution: 128 * 64 Viewing angle:> 160 ° Supports many control chip: Fully compatible with Arduino, 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc. Ultra-low power consumption: full screen lit 0.08W Voltage: 3V ~ 5V DC Working Temperature: -30 c ~ 70 c Module Size:  27.3MM *27.8MM I2C/IIC Interface, need 2 IO only. Driver IC: SSD1306       Package Included: 1PCS * New  yellow-blue 0.96" I2C IIC SPI Serial 128X64 OLED LCD LED Display Module for Arduino Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

XL power module + LED Voltmeter DC-DC Boost module with adjustable voltage meter display Description: Input voltage:V Output voltage:5-52V Maximum input current:4A Transfer efficiency:94% Output ripple:50mV Operating temperature:-℃ Switching frequency:400KHz Output ripple:50mV Load regulation:±0.5% Voltage regulation:±0.5% operating temperature:-℃ Size: Functions: Short press: input/output display options Moderate press: Enter the fine-tuning state.Increase or decrease the offset (the default is 0) when the voltage display inaccurate use.Short according to the regulation, long press or long according to restore Long press: the state of low power consumption, the digital tube and the lights are out, the normal work of the module. Click the button again to restore. Normal display Clockwise to adjust output voltage: Clockwise—– increasing voltage Counterclockwise—-reduce the voltage Reverse protection diodes prevent reverse connection High-frequency bypass capacitor electric spark Note: The output voltage must be higher than the input voltage. Related questions: Q. Why the voltmeter reading error sometimes feel? A. This is because the input voltage is corrugated. Q. Voltmeter voltage are shaking is why? A. The voltmeter is a high precision voltage meter. After many tests, the accuracy is 1%. If there is a rock, that the measured voltage is not stable. Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

Item specifics Product Description Specification: Note: 1. /"LIGHT/" linked with GND, the backlight to be lit. 2. Need you to compress the screen and PCB tighter, might got loose after the delivery. 3 Use a 3.3V controller, otherwise the display could be quite vague. LCD Module:   Power supply voltage:2.7V-3.3V,5V is OK,but part of the screen becomes black when tested? Data interface level:2.7-5V? Backlight power supply voltage:highest 3.3V? Module size:43.6mm x 43.1mm(width X height)? Installation diameter:2mm? Backlight:White Document for Download:Data 1RST--------- reset? 2CE------------chip selection? 3DC-----------data/commands choice? 4DIN-----------serial data line? 5CLK------------serial Clock Spee 63.3V------------VCC? 7LIGHT--------- backlight control terminal? 8GND-----------power negative Features: 84 X 84 dot matrix LCD,can show 4 lines of characters Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting time. Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace. LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small Low power supply,the working current

MAX LED Module 8-Digit 7 Segment Digital LED Display Tube For Arduino MCU MAX Digital Tube Display Module MAX is a kind of integrated serial input/output common cathode display driver, it connects microprocessor and 8 digit 7 period of digital LED display, also can be connected to the bar graph display or 64 independent LED. It includes a piece of type B BCD coder, multiple scanning circuit, period of word drive, but also an 8 * 8 static RAM used to store every data. Only an external register used to set each LED segment current. A convenient four wire serial interface can connection all general microprocessor. Each data can be addressed

3.3V-5V 0.96" LCD Modules SPI 128X64 SSD OLED LCD Display Module Arduino CLK MOSI STM32/AVR/51 Mmm Features: What is OLED? OLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel displays. How Does OLED Emit Light? OLEDs basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electroluminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components. Specifications: No backlight, the display unit can be self-luminous LED colour: yellow and blue High resolution: Viewing angle:> 160 Supports many control chip: Fully compatible with Arduino, 51 series, MSP430 series, STM32 / 2, CSR chip, etc. Ultra-low power consumption: full screen lit 0.08W, 0.06W normal full-screen display of Chinese characters Wide voltage support: without any modification, directly supports 3V ~ 5V DC Working temperature: -30 C ~ 70 C Minimum occupancy on Earth IO port display: The SPI communication, as long as the two IO ports will be able to drive! Driver IC: SSD No font: take the word with modulo software Size Reference Module volume (generous): 27.0MM * 27.0MM * 4.1MM Please Note: Due to hand measure, the size may have 1-4 cm error Due to Different Monitor, the color may have difference Package Included: 1x LCD Modules 3.3V-5V 0.96" LCD Modules SPI 128X64 SSD OLED LCD Display Module Arduino CLK MOSI STM32/AVR/51 Mmm 100% perfectly working, will be properly checked before shipment. For new users: ------------------- if you are new users we created a git hub with required library, please visit it, read the read me file and follow the instructions, then you will be able to setup OLED

Sound Sensor High Sensitivity Sound Detection Module for Arduino Features: 1.84 X 84 dot matrix LCD, can show 4 lines of characters 2.Use serial interface communicate with the master processor, the number of interface signal line reduced greatly, only 8 signal lines including power and GND. 3.Support different types of MCU, such as the arduino, AVR, SPI, MCS51 and so on. 4.Transfer rate up to 4Mbps, can full speed write display data without waiting time. 5.Can use the conductive glue to connect the module with the printed board, without cables. The metal hooks on the module can fix the module on the printed board, which is very easy to install and replace. 4.LCD controller/driver chip has been bound to LCD chip, the volume of LCD is small 5.Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode Connections: 1.RST--------- reset 2.CE---------- chip selection 3.DC---------- data/commands choice 4.DIN--------- serial data line 5.CLK--------- serial Clock Speed 6.3.3V-------- VCC 7.LIGHT------- backlight control terminal 8.GND--------- power negative Specifications: 1.For Nokia 5110 3V-5V 2.Module size: 45.2mm x 43.1mm Package included: 1x LCD Module for Nokia 5110 Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

IIC/I2C/TWI Serial Interface Board Module Port For Arduino LCD Display IIC/I2C/TWI Serial Interface Board Module Port For Arduino LCD Display Features Supply voltage: 5V the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable Compatible for LCD This is another great IIC/I2C/TWI/SPI Serial Interface With this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices

DESCRIPTION 5 x 7 Dot Matrix Led Display Based on the electrode connections, two types of LED matrices are explained below: An LED matrix with a common anode for LEDs in a row when a row of LEDs feature a common anode, the LEDs in each column must include a common cathode. An LED matrix with a common cathode for LEDs in a row when a row of LEDs feature a common cathode, the LEDs in each column must include a common anode. It is a Common Anode in a row Matrix LED Display. This display module has a special feature of bi color led. The pin configuration of the Module helps in selecting between colors as well. The display module has Pin out which can be perfectly distinguished for desired outcomes. Features: - 1.5 x 7 LED matrixes. 2. All bi Color LEDs (GREEN and RED) 3. Digital device Interface. 4. Easy to Control. 5. Operating Voltage: - 5 V We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

IIC/I2C/TWI/SPI Serial Interface Board Module Port For Arduino LCD Display IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, you may not be able to use normal LCD shield after connecting a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display with only 2 wires. Features: Specifications: Supply voltage: 5V Backlight & Contrast can be adjusted by inbuilt potentiometer. Comes with 2 IIC interface, which can be connected by Dupont wires or IIC dedicated cable Compatible for LCD (16x2) Using this I2C interface module, you can realize data display with only 2 wires. Backlight can be switched using onboard jumper. Size: mm(max) Please contact us for any doubt.Please give us positive feed back.Your feed back is very important for us. Happy to help you.We shipped our material within 2 working days after getting confirmation of payment. contact us- Mob:-     (From 10 AM to 9 PM)    Powered by Turbo Lister

Description：   84 X 84 dot matrix LCD,can show 4 lines of characters   Power supply voltage:2.7V-3.3V   Data interface level:2.7-5V   Backlight power supply voltage:highest 3.3V   Module size:43.6mm(width) x 43.1mm(length)   Installation diameter:2mm Pin Definition:   1.RST--------- reset   2.CE---------- chip selection   3.DC---------- data/commands choice   4.DIN--------- serial data line   5.CLK--------- serial Clock Speed   6.3.3V-------- VCC   7.LIGHT------- backlight control terminal   8.GND--------- power negative 3.Features: 1>. 84 X 84 dot matrix LCD,can show 4 lines of characters 2>. Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the arduino,AVR,PIC,STM32,STC MSP430 and so on.Transfer rate up to 4Mbps,can full speed write display data without waiting time. 3>. Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace. 4>. LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small 5>. Low power supply,the working current

Yellow + Blue 0.96" SPI Serial 128x64 OLED LCD Display Module 3-5V SSD   Fully functioning Software Code(AVR) included with English Font.        Product Summary: OLED SPI Operating Voltage 3-5V Input Voltage (recommended) 5V Input Voltage (limits) 3-5V No. of Pins 6 Power Pins 2(VCC,GND) LED colour Yellow and Blue |||||| & |||||| Resolution 128 x 64 View angle >160 Power consumption 0.08w at full screen lit Working temperature -30C ~ 70C Control Chip SSD Module size(Approx.) mmx27.1mmx4.1mm Module weight 0.06kg (lb.)

White 0.96" SPI Serial 128x64 OLED LCD Display Module 3-5V SSD   Fully functioning Software Code(AVR) included with English Font.        Product Summary: OLED SPI Operating Voltage 3-5V Input Voltage (recommended) 5V Input Voltage (limits) 3-5V No. of Pins 6 Power Pins 2(VCC,GND) LED colour White Resolution 128 x 64 View angle >160 Power consumption 0.08w at full screen lit Working temperature -30C ~ 70C Control Chip SSD Module size(Approx.) mmx27.1mmx4.1mm Module weight 0.06kg (lb.)

Product Description   MAX Digital Tube Display Module   MAX is a kind of integrated serial input/output common cathode display driver, it connects microprocessor and 8 digit 7 period of digital LED display, also can be connected to the bar graph display or 64 independent LED. It includes a piece of type B BCD coder, multiple scanning circuit, period of word drive, but also an 8 * 8 static RAM used to store every data. Only an external register used to set each LED segment current. A convenient four wire serial interface can connection all general microprocessor. Each data can be addressed

IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, you may not be able to use normal LCD shield after connecting a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display with only 2 wires. Features: Specifications: Supply voltage: 5V Backlight & Contrast can be adjusted by inbuilt potentiometer. Comes with 2 IIC interface, which can be connected by Dupont wires or IIC dedicated cable Compatible for LCD (16x2) Using this I2C interface module, you can realize data display with only 2 wires. Backlight can be switched using onboard jumper. Size: mm(max)

To satisfy electronic DIY hobbyists, we has developed MAX Dot Matrix Module. It uses the Max chip which do a great job on saving of MCU I/O. It can not only control each point individually, but also can be extended without limitation to meet your requirements on LED Sign, Team Logo and so on. A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module size: 5 cm long X 3.2 cm wide X 1.5 cm high With four screws hole, aperture 3mm Module with input and output interfaces Supports multiple modules cascade Led colour: Red

Package Contents Adjustable DC-DC converter power supply module upgrades LM voltage regulator module with voltage meter display Feature: 100% Brand new and high quality Input voltage range: 4-40 v (40 v to limit the highest voltage). Output voltage range:1.25V -37V (decompression mode, input output must be greater than 2 V above). Output current: 2 A continuous output. Output power: the maximum 15 w. Ripple frequency: 150 KHZ. Grain wave peak: 100 mv. Voltmeter precision: ± 5 ‰. Tatic power: 20 ma (and input voltage output voltage and digital tube color is closely related to the actual current will exist deviation). With voltage display function, the displayed accuracy is ± 0.05V, range is 0 - 40V.(Note:

Item specifics Usage: Indoor Tube Chip Color: Red Display Function: Graphics is_customized: Yes MAX module: finished goods Product Description MAX is an integrated serial input / output common-cathode display drivers, which connects the microprocessor 7-segment digital LED display with 8 digits, bar graph can also be connected monitor or 64 separate LED. On type B BCD encoder includes an on-chip, multi-channel scanning loop, segment word drive, but also a 8x8 static RAM for storing each data. Only one external register is used to set the segment current for each LED. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed

IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, you may not be able to use normal LCD shield after connecting a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display with only 2 wires. Features: Specifications: Supply voltage: 5V Backlight & Contrast can be adjusted by inbuilt potentiometer. Comes with 2 IIC interface, which can be connected by Dupont wires or IIC dedicated cable Compatible for LCD (16x2) Using this I2C interface module, you can realize data display with only 2 wires. Backlight can be switched using onboard jumper. Size: mm(max) = MM_contentVersion; } else if (navigator.userAgent && navigator.userAgent.indexOf("MSIE")>=0 && (navigator.appVersion.indexOf("Win") != -1)) { document.write(' /n'); document.write('on error resume next/n'); document.write('MM_FlashCanPlay = (IsObject(CreateObject("ShockwaveFlash.ShockwaveFlash." & MM_contentVersion)))/n /n'); } if (MM_FlashCanPlay) { document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); document.write(' '); } else { document.write(' '); document.write(' '); document.write(' The Buyer Appreciation banner is best viewed with Macromedia Flash Player 6 or higher. '); document.write(' Click here to get the latest Macromedia Flash Player. '); document.write(' '); document.write('