Usb based isp programmer

9% Discount 31st March coupon code:  COUPONDUN9 1.     About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

USBtinyISP AVR ISP programmer for Arduin bootloader Product Description USBtinyISP is designed for AVR,based on USB connector's ISP download wire. Officially supported by Arduino IDE, we can burn Arduino bootloader onto chips, and practically program any Atmel AVR microcontroller by this powerful AVR ISP programmer. * Both 6-pin and 10-pin AVR-standard interfaces * 2 LEDs to indicate "USB/Power good" and "Busy" * USB powered         Steps to burn Arduino bootloader: 1. Download driver(http://blog.arduino.cn/wp-content/uploads//usbtinyisp-w32-driver-v112.zip), unzip and install 2. When you see “USBtinyISP AVR Programmer”

FREE USB CABLE + & AVR USB ISP Programmer (ENTER COUPON CODE WHEN YOU PROCEED TO PAY)   GET FREE 9% Discount Use Coupon CODE: 09DEAL     Product Overview   1.     About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

1.      About USB AVR and AT89Sxx ISP Programmer   USB AVR and AT89Sxx ISP  (In System programming)  Programmer is low cost USB based programmer.There is no need to take out target micro controller from the development Board. This programmer will work with a wide variety of Atmel AVR and AT89Sxxxx microcontroller. They quite compact, but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done

This compact USB ISP programmer is for ATMEL, AVR 51, ATMega, ATTiny, ATMEGA8 and ATMEGA128 plus many more. The USB interface is achieved via an ATMEGA processor and the rest is done

Starter_AVR USB is introductory board for the AVR family of microcontrollers. The board has  Atmega32 MCU with UART bootloader,  hence no external programmer is required. Bootloader occupies approximates 2K Bytes of flash memory, remaining 30K Bytes can be used for user programming. Features Atmega32 MCU 32K bytes of In-System Self Programmable Flash Memory 1024 bytes EEPROM 2K bytes Internal SRAM 32 IO pins UART, SPI, JTAG and I2C support. Real Time Counter with Separate Oscillator Four PWM Channels**8-channel, 10-bit ADC 8 Single-ended Channels 2 Differential Channels with Programmable Gain at 1x, 10x, or 200x USB Interface CP2102: for communicating with the host computer. LCD Interface: 16 characters, 2 lines Test Leds (2) and Switches(2) 5X2 ISP Programmer Connector Breakout for all Ports Breakout for +5v,Gnd and Vin Power Supply compatible with AC/DC adapters(9 to 12V DC, 1A). Physical Features Dimensions: 70mm X 90mm 1.6mm Glass Epoxy, FR4 PCB Wave Soldered. Downloads: Schematic Sample Code For more details, technical support and downloads visit the product page.

  Description Package Includes: F01982 AVR USB USBasp ISP PRGMR Programmer FOR KK MultiCopter KG261 Feedback: We provide good quality products & maintain high service standards.  We strive for 100% positive feedback for our work.  For assistance, please contact us on  by PhraseFinder" style="border: none !important; display: inline-block !important; text-indent: 0px !important; float: none !important; font-weight: bold !important; height: auto !important; margin: 0px !important; min-height: 0px !important; min-width: 0px !important; padding: 0px !important; text-transform: uppercase !important; text-decoration: underline !important; vertical-align: baseline !important; width: auto !important; background: transparent !important;"> Message  or  sales@KitsGuru.com Providing Neutral or Negative feedback will not solve anything.  Please contact us and we will try to solve your issue within 48 hours. Contact us on our dedicated Line  +91 9560773418 between 10:00AM - 7:00PM Customer Support: Do you have doubts regarding any of our products?  Any of our product is not working?.  Do you want to order

This is programmer for  89  series microcontrollers like  89C51,C52,S51,S52,C,C  and such series from Atmel. Board also supports various 8 pin serial EEPROM ICs. ZIF socket enables easy insertion and removal of devices for programming. Programming is very fast and reliable since it is USB based. No external power required since it is powered from USB port itself. Features •     Supports  89C51,C52,S51,S52,C,C  series & serial EEPROM devices. •     Powered from USB port(No external power required). •     High speed writing (8kb flash file

Description This programmer is based on Thomas Fischl's USBasp design and connects to your computer's USB port. Not only is it quite compact, but the design is really elegant. The USB interface is achieved by using an atmega processor and the rest is done

100% Brand New Sofi SP8-A High Speed USB Universal Programmer 100% original bit SP8-A universal programmer is professional SOFI SP8 series programmers, SOFI SP8-A programmer is designed for programming serial FLASH/EEPROM/SPI memories,with built-in 32-bit high-speed processors and USB2.0 communication interfaces.  SOFI SP8-A universal programmer Flash EEPROM SPI BIOS SOFI SP8-A universal programmer supports high-speed programming of nearly all /BR90 chips. In the number of supportive serial memories and the writing speed, it greatly exceeds most general and similar special programmers that cost over RMB. It has a unique function of ISP online programming and supports more chips with continuous software upgrade. With exquisite shells made through professional mould opening and with advanced software/hardware design. SP8-A programmer is popular edition: It applies to personnel of home appliance and digit maintenance. With the cost of only 1xx RMB, it is the first version of special programmers for professional serial memories. It far exceeds other products at the same price level, and has uncommon performance/price ratio Three types SOFI SP8 series programmers: SP8-A, SP8-B and SP8-F. SP8 is special programmers with the highest speed for programming serial memories (Note 1), the most types of supportive devices (Note 2) and the highest performance/price ratio

100% Brand New Sofi SP8-A High Speed USB Universal Programmer 100% Original SP8-A universal programmer is professional SOFI SP8 series programmers, SOFI SP8-A programmer is designed for programming serial FLASH/EEPROM/SPI memories,with built-in 32-bit high-speed processors and USB2.0 communication interfaces.  SOFI SP8-A universal programmer Flash EEPROM SPI BIOS SOFI SP8-A universal programmer supports high-speed programming of nearly all /BR90 chips. In the number of supportive serial memories and the writing speed, it greatly exceeds most general and similar special programmers that cost over RMB. It has a unique function of ISP online programming and supports more chips with continuous software upgrade. With exquisite shells made through professional mould opening and with advanced software/hardware design. SP8-A programmer is popular edition: It applies to personnel of home appliance and digit maintenance. With the cost of only 1xx RMB, it is the first version of special programmers for professional serial memories. It far exceeds other products at the same price level, and has uncommon performance/price ratio Three types SOFI SP8 series programmers: SP8-A, SP8-B and SP8-F. SP8 is special programmers with the highest speed for programming serial memories (Note 1), the most types of supportive devices (Note 2) and the highest performance/price ratio

Features Flash Burner for AVR Series from ATMEL and Microcontrollers. Communication - USB Auto Erase before writing and Auto Verify after writing Freeware AVR GCC C Compiler ISP Programming Socket Connects through AVR DUDE USB Powered Device Support AT89s51, AT89s52, AT89s53, AT89s AT90S, ATMEGA, ATMEGA ATMEGA ATTINY AT90CAN - AT90PWM2,3 Package Contents Programmer BRD FREE USB Port Cable FREE 6 Burg Cable Female 2 Female Programmer Driver (will be sended through Email) Programming Software For AVR and . (will be sended through Email)

AVR USB Programmer with case USBasp USBISP for ATMEL ATmega ATtiny microcontrollers. Painless AVR controller programming   Product Description: Main Features: ·         Brand new and high quality ·         Support for Linux, Mac OS X and Windows ·         5 KB/sec maximum write speed. ·         10 pin ISP interface. ·         Can be used with Khazama, AVRDUDE, PonyProg and other ·          Support for AVRDUDE from version 5.2 onwards   Supported devices: Mega Series: ATmega8 – ATmega48 – ATmega88 – ATmega168 – ATmega328 – ATmega103 – ATmega128 – ATmega – ATmega – ATmega16 – ATmega161 – ATmega162 – ATmega163 – ATmega164 – ATmega169 – ATmega – ATmega – ATmega32 – ATmega324 – ATmega329 – ATmega – ATmega64 – ATmega640 – ATmega644 – ATmega649 – ATmega – ATmega – ATmega Tiny Series ATtiny12 – ATtiny13 – ATtiny15 – ATtiny25 – ATtiny26 ATtiny45 – ATtiny85 – ATtiny   Classic Series AT90S – AT90S – AT90S – AT90S – AT90S AT90S – AT90S – AT90S AT90S  CAN Series AT90CAN128 PWM Series AT90PWM2 – AT90PWM3 Package includes: ·         1 x USB AVR Programmer with case ·         1 x 10-pin programming cable ·         A plastic container box.   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·        In case you find any problem

Product Description:  Supports AVRDude   Support for Linux, Mac OS X and Windows  XP, pin ISP interface Supports all Atmega microcontrollers that provide the port for the plug. easily program kk board. Package includes: 1x programmer 1x ribbon cable

PACKAGE CONTAINS: 1. USBasp Programmer 2. 5x2 FRC Cable 3. USB Cable Supported microcontrollers include:  Mega Series ATmega8 ATmega48 ATmega88 ATmega168 ATmega328 ATmega103 ATmega128 ATmega ATmega ATmega16 ATmega161 ATmega162 ATmega163 ATmega164 ATmega169 ATmega ATmega ATmega32 ATmega324 ATmega329 ATmega ATmega64 ATmega640 ATmega644 ATmega649 ATmega ATmega ATmega Tiny Series ATtiny12 ATtiny13 ATtiny15 ATtiny25 ATtiny26 ATtiny45 ATtiny85 ATtiny Setting up the XploreFlash Programmer Step 1: Xplore flash is based on various opensource software, it requires avrdude. Avrdude is part of WinAVR GCC complier. Download and install it. Step 2: Download and install USB driver for the programmer. Step 3: Download and install XploreFlash GUI. (XploreFlash GUI is based on AVRDUDESS) Step 4: Follow Step by step guide on using the programmer software XploreFlash program the micrcontroller. The GUI software will require.NET framework 2.0 or later please download and install it. For additional details and technical support visit the Xplore Flash page.