Avr serial

Detailed Product Description AVR Programmer With Serial Communication FEATURES: It is used to load the programme into AVR microcontroller through DB9 connector and FRC connector. It is used for serial communication. It contain Serial Cable,FRC Cable,Software CD. CONTENTS: 1 Programmer 1 FRC cable 1 Serial cable 1 Software CD

With this board you can develop and prototype with ATMEGA16/ATMEGA pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters.   FEATURES AVR Development Board for Atmel ATMEGA ISP Socket for Flashing On board Regulated Power Supply 5v,12v supplys Easy to test with Burg Connecters wires An RS232 Serial Port 7Seg Mulitplexed Display DC Power Supply Connector(12v Ac or Dc) READY INTERFACE For LCD display 2linex16Character 24Cxx (I2C) (EEPROM) RTC (DS LED array Matrix Key Pad 4 Interrupt Switches +12v Relay (one) Package Content   AVR Development Board (WITH CHIP MAX232) Burg Connecters 20 Nos Female to Female.

1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU. Order more than one piece to save shipping cost. You can contact us at + for any question or concern. Device Details This is a USB to Serial Converter Module based on PL-HX IC Device Specifications Based on PL-HX IC 5 Pins - 3.3V, 5.0V, TXD, RXD, GND Can be used to program Arduino Pro Mini. Package Include 1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU 5 x Femalre to Femalre Jumper Wires (Note: Wire Colour May Vary) About Us We are a small company based

1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU. Order more than one piece to save shipping cost. You can contact us at +91 94625 64100 for any question or concern. Device Details This is a USB to Serial Converter Module based on PL-2303HX IC Device Specifications Based on PL-2303HX IC 5 Pins - 3.3V, 5.0V, TXD, RXD, GND Can be used to program Arduino Pro Mini. Package Include 1 Piece USB 2.0 to TTL UART Serial Converter Adapter for Arduino, AVR, ARM / Other MCU 5 x Femalre to Femalre Jumper Wires (Note: Wire Colour May Vary) About Us We are a small company based

Description：   84 X 84 dot matrix LCD,can show 4 lines of characters   Power supply voltage:2.7V-3.3V   Data interface level:2.7-5V   Backlight power supply voltage:highest 3.3V   Module size:43.6mm(width) x 43.1mm(length)   Installation diameter:2mm Pin Definition:   1.RST--------- reset   2.CE---------- chip selection   3.DC---------- data/commands choice   4.DIN--------- serial data line   5.CLK--------- serial Clock Speed   6.3.3V-------- VCC   7.LIGHT------- backlight control terminal   8.GND--------- power negative 3.Features: 1>. 84 X 84 dot matrix LCD,can show 4 lines of characters 2>. Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the arduino,AVR,PIC,STM32,STC MSP430 and so on.Transfer rate up to 4Mbps,can full speed write display data without waiting time. 3>. Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace. 4>. LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small 5>. Low power supply,the working current

      The USB to RS232 converter board is most essential bridge needed to connect serial device to log the data to pc or laptop. If you have a development board like 8051, AVR, PIC or any other with serial UART or RS232 connector. Then use the USB to RS232 converter to connect these devices for programming or communication with the PC or Laptop.              Now a days most of the laptops does not have COM ports to connect directly with RS232 cable. So use i-labz USB to RS232 converter for interfacing. If you are planning to buy 8051, AVR, PIC or any other boards like GSM modem, GPS, Bluetooth, Finger print scanner or Ultrasonic distance finder then you must use USB to RS232 connector for connecting or troubleshooting with laptop. CP210x Driver Installation Guide - USB Driver Installation Instructions Download Terminal tool for Troubleshooting(winXP/7/8)               To test the USB to RS232 converter use windows hiighper terminal (using winXP as OS) or terminal tool. The procedure to test to setup the highper terminal is explained

ESP serial Wi-Fi UART wireless IOT module 3.3V AP+STA   For RasPi, arduino, AVR, other MCU ESP serial wifi Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.   Product Description esp serial wifi:   ESP is a highly integrated chip designed for the needs of a new connected IoT world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. Note:   This module requires a 3.3V supply for VCC, and 3.3V logic. It is not 5V tolerant. Connecting Rx or Tx on 5V Arduino may destroy this module. You must use a logic level converter, or a 3.3V Arduino. Also the 3.3V supply on the Arduino Uno has inadequate current capability to power this module. You must provide a separate, higher 3.3V supply (about 300mA or better)   Features ESP serial wifi: ·         SDIO 2.0, SPI, UART ·         Integrated RF switch, balun, 24dBm PA, DCXO, and PMU ·         Integrated RISC processor, on-chip memory and external memory interfaces ·         Integrated MAC/baseband processors ·         Quality of Service management ·         I2S interface for high fidelity audio applications ·         On-chip low-dropout linear regulators for all internal supplies ·         Proprietary spurious-free clock generation architecture ·         Integrated WEP, TKIP, AES, and WAPI engines   Specification ESPEX: ·             b/g/n ·             Wi-Fi Direct (P2P), soft-AP ·             Integrated TCP/IP protocol stack ·             Integrated TR switch, balun, LNA, power amplifier and matching network ·             Integrated PLLs, regulators, DCXO and power management units ·             +19.5dBm output power

3.3V-5V 0.96" LCD Modules SPI 128X64 SSD OLED LCD Display Module Arduino CLK MOSI STM32/AVR/51 Mmm Features: What is OLED? OLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel displays. How Does OLED Emit Light? OLEDs basic structure consists of organic materials positioned between the cathode and the anode, which is composed of electric conductive transparent Indium Tin Oxide (ITO). The organic materials compose a multi-layered thin film, which includes the Hole Transporting Layer (HTL), Emission Layer (EML) and the Electron Transporting Layer (ETL). By applying the appropriate electric voltage, holes and electrons are injected into the EML from the anode and the cathode, respectively. The holes and electrons combine inside the EML to form excitons, after which electroluminescence occurs. The transfer material, emission layer material and choice of electrode are the key factors that determine the quality of OLED components. Specifications: No backlight, the display unit can be self-luminous LED colour: yellow and blue High resolution: Viewing angle:> 160 Supports many control chip: Fully compatible with Arduino, 51 series, MSP430 series, STM32 / 2, CSR chip, etc. Ultra-low power consumption: full screen lit 0.08W, 0.06W normal full-screen display of Chinese characters Wide voltage support: without any modification, directly supports 3V ~ 5V DC Working temperature: -30 C ~ 70 C Minimum occupancy on Earth IO port display: The SPI communication, as long as the two IO ports will be able to drive! Driver IC: SSD No font: take the word with modulo software Size Reference Module volume (generous): 27.0MM * 27.0MM * 4.1MM Please Note: Due to hand measure, the size may have 1-4 cm error Due to Different Monitor, the color may have difference Package Included: 1x LCD Modules 3.3V-5V 0.96" LCD Modules SPI 128X64 SSD OLED LCD Display Module Arduino CLK MOSI STM32/AVR/51 Mmm 100% perfectly working, will be properly checked before shipment. For new users: ------------------- if you are new users we created a git hub with required library, please visit it, read the read me file and follow the instructions, then you will be able to setup OLED

Yellow + Blue 0.96" SPI Serial 128x64 OLED LCD Display Module 3-5V SSD   Fully functioning Software Code(AVR) included with English Font.        Product Summary: OLED SPI Operating Voltage 3-5V Input Voltage (recommended) 5V Input Voltage (limits) 3-5V No. of Pins 6 Power Pins 2(VCC,GND) LED colour Yellow and Blue |||||| & |||||| Resolution 128 x 64 View angle >160 Power consumption 0.08w at full screen lit Working temperature -30C ~ 70C Control Chip SSD Module size(Approx.) mmx27.1mmx4.1mm Module weight 0.06kg (lb.)

White 0.96" SPI Serial 128x64 OLED LCD Display Module 3-5V SSD   Fully functioning Software Code(AVR) included with English Font.        Product Summary: OLED SPI Operating Voltage 3-5V Input Voltage (recommended) 5V Input Voltage (limits) 3-5V No. of Pins 6 Power Pins 2(VCC,GND) LED colour White Resolution 128 x 64 View angle >160 Power consumption 0.08w at full screen lit Working temperature -30C ~ 70C Control Chip SSD Module size(Approx.) mmx27.1mmx4.1mm Module weight 0.06kg (lb.)

Atmega8L - 28Pins 8MHz 8kb 8-bit Microcontroller FREE 28 PIN DIP SOCKET  Features 28-pin AVR Microcontroller Flash Program Memory: 8 kbytes EEPROM Data Memory: 512 bytes SRAM Data Memory: 1 kbytes I/O Pins: 23 Timers: Two 8-bit / One 16-bit A/D Converter: 10-bit Six Channel PWM: Three Channels RTC: Yes with Separate Oscillator MSSP: SPI and I²C Master and Slave Support USART: Yes External Oscillator: up to 8MHz Specifications High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture 130 Powerful Instructions - Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Up to 16 MIPS Throughput at 16MHz Fully Static Operation On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 8k Bytes of In-System Self-Programmable Flash Optional Boot Code Section with Independent Lock Bits 512K Bytes EEPROM Programming Lock for Software Security 1K Byte Internal SRAM Peripheral Features On-chip Analog Comparator Programmable Watchdog Timer with Separate On-chip Oscillator Master/Slave SPI Serial Interface Two 8-bit Timer/Counters with Separate Prescalar, Compare  One 16-bit TImer/Counter with Separate Prescaler, Compare and Capture mode Real TIme Counter with Separate Oscillator Four PWM Channels 8-channel, 10-bit ADC Byte-oriented Two-wire Serial Interface Programmable Serial USART Special Mircocontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages 23 Programmable I/O Lines 28-pin PDIP, 32-lead TQFP, and 32-pad MLF Operating Voltages V for ATmega8L Speed Grades 0-16 MHz for ATmega8 Power Consumption @ 4 MHz, 3V, and 35°C for ATmega8L Active: 3.6mA Idle Mode: 10mA Power-down Mode: 0.5µA

The Atmel  8-bit   AVR   RISC -based microcontroller combines 32 KB  ISP   flash  memory with read-while-write capabilities, 1 KB  EEPROM, 2 KB  SRAM, 23 general purpose I/O lines, 32 general purpose working  registers, three flexible timer/ counters  with compare modes, internal and external  interrupts, serial programmable  USART, a byte-oriented 2-wire serial interface,  SPI  serial port, 6-channel 10-bit  A/D converter  (8-channels in  TQFP  and  QFN / MLF  packages), programmable  watchdog timer  with internal  oscillator, and five software selectable power saving modes. The device operates between volts. The device achieves throughputs approaching 1  MIPS  per MHz. Key parameters [edit] PARAMETERS VALUE Flash 32 Kbytes RAM 2 Kbytes Pin Count 28 Max. Operating Frequency 20 MHz CPU 8-bit AVR # of Touch Channels 16 Hardware QTouch Acquisition No Max I/O Pins 26 Ext Interrupts 24 USB Interface No USB Speed No

Description: Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new AVRDUINO (Arduino compatible) Board. In addition to all the features of the previous board, the AVRDUINO now uses an ATmega KFlash Memory) which can be programmed through Arduino software as well as any AVR programming software. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed). Features: ATmega328 microcontroller (Self Programmable) CAN be used as ARDUINO Board as well as AVR's 28 PIN ATMEGA328 DEVELOPMENT BOARD. Buit In Power Supply: Input voltage -  +7-+12V 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs 32k Flash Memory 16Mhz Clock Speed No Need of any Programmer Package Contents: 1) AVRDuino Board (With ATMEGA328 MICROCONTROLLER) 2) INSTRUCTION MANUAL(Will be sended through Email) 3) DRIVER DETAILS(Will be sended through Email) 4) USB CABLE (FOR CONNECTING AVRDUINO WITH PC/LAPTOP) 5) TUTORIAL OF BURNING PROGRAM OF LED TOGGLE THROUGH Arduino software as well as any AVR programming software. (Will be sended through Email) NOTE: AVRDuino have a dual nature, first as AVR Development Board, second as ARDUINO COMPATIBLE BOARD. Because of its Dual Nature AVRDuino Doesn't Support Serial Monitor

Description: Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new AVRDUINO (Arduino compatible) Board. In addition to all the features of the previous board, the AVRDUINO now uses an ATmega8 which can be programmed through Arduino software as well as any AVR programming software. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed). Features: ATmega8 microcontroller (Self Programmable) CAN be used as ARDUINO Board as well as AVR's 28 PIN ATMEGA8 DEVELOPMENT BOARD. Buit In Power Supply: Input voltage -  +7-+12V 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs 8k Flash Memory 16Mhz Clock Speed No Need of any Programmer Package Contents: 1) AVRDuino Board (With ATMEGA8 MICROCONTROLLER) 2) INSTRUCTION MANUAL(Will be sended through Email) 3) DRIVER DETAILS(Will be sended through Email) 4) USB CABLE (FOR CONNECTING AVRDUINO WITH PC/LAPTOP) 5) TUTORIAL OF BURNING PROGRAM OF LED TOGGLE THROUGH Arduino software as well as any AVR programming software. (Will be sended through Email) Regards, Robosoft Labs NOTE: AVRDuino have a dual nature, first as AVR Development Board, second as ARDUINO COMPATIBLE BOARD. Because of its Dual Nature AVRDuino Doesn't Support Serial Monitor

Atmega328P - PU - 28Pins 20MHz 32kb 8-bit Microcontroller FREE 28 PIN DIP SOCKET  Features High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture 131 Powerful Instructions - Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Up to 6 MIPS Throughput at 16MHz Fully Static Operation On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 32k Bytes of In-System Self-Programmable Flash Optional Boot Code Section with Independent Lock Bits 1K Bytes EEPROM Programming Lock for Software Security Peripheral Features On-chip Analog Comparator Programmable Watchdog Timer with Seperate On-chip Oscillator Master/Slave SPI Serial Interface Two 8-bit Timer/Counters with Separate Prescalar, Compare  One 16-bit TImer/Counter with Seperate Prescaler, Compare and Capture mode Real TIme Counter with Seperate Oscillator Six PWM Channels 8-channel, 10-bit ADC Byte-oriented Two-wire Serial Interface Programmable Serial USART Special Mircocontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages 23 Programmable I/O Lines 28-pin PDIP, 32-lead TQFP, and 28-pad MLF Operating Voltages V for ATmega328P Speed Grades 0-20 MHz for ATmega328P Power Consumption at 1 Mhz, 1.8V, 25 °C Active: 0.2mA Power-down Mode: 0.1µA

AtmegaPins 16MHz 16kb 8-bit Microcontroller FREE 40 PIN DIP SOCKET  Features High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture 131 Powerful Instructions - Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Up to 6 MIPS Throughput at 16MHz Fully Static Operation On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 16k Bytes of In-System Self-Programmable Flash Optional Boot Code Section with Independent Lock Bits 512K Bytes EEPROM Programming Lock for Software Security JTAG (IEEE std. Compliant) Interface Boundary-scan Capabilities According to the JTAG Standard Extensive On-chip Debug Support Programming of Flash, EEPROM, Fuses, and Lock Bits through the JAGS Interface Peripheral Features On-chip Analog Comparator Programmable Watchdog Timer with Separate On-chip Oscillator Master/Slave SPI Serial Interface Two 8-bit Timer/Counters with Separate Prescalar, Compare  One 16-bit TImer/Counter with Separate Prescaler, Compare and Capture mode Real Time Counter with Separate Oscillator Four PWM Channels 8-channel, 10-bit ADC Byte-oriented Two-wire Serial Interface Programmable Serial USART Special Mircocontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages 32 Programmable I/O Lines 40-pin PDIP, 44-lead TQFP, and 44-pad MLF Operating Voltages V for ATmega16 Speed Grades 0-16 MHz for ATmega16 Power Consumption at 4 Mhz, 3V, 35 °C Active: 1.1mA Idle Mode: 0.35mA Power-down Mode:

Sound Sensor High Sensitivity Sound Detection Module for Arduino Features: 1.84 X 84 dot matrix LCD, can show 4 lines of characters 2.Use serial interface communicate with the master processor, the number of interface signal line reduced greatly, only 8 signal lines including power and GND. 3.Support different types of MCU, such as the arduino, AVR, SPI, MCS51 and so on. 4.Transfer rate up to 4Mbps, can full speed write display data without waiting time. 5.Can use the conductive glue to connect the module with the printed board, without cables. The metal hooks on the module can fix the module on the printed board, which is very easy to install and replace. 4.LCD controller/driver chip has been bound to LCD chip, the volume of LCD is small 5.Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode Connections: 1.RST--------- reset 2.CE---------- chip selection 3.DC---------- data/commands choice 4.DIN--------- serial data line 5.CLK--------- serial Clock Speed 6.3.3V-------- VCC 7.LIGHT------- backlight control terminal 8.GND--------- power negative Specifications: 1.For Nokia 5110 3V-5V 2.Module size: 45.2mm x 43.1mm Package included: 1x LCD Module for Nokia 5110 Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Item specifics Product Description Specification: Note: 1. /"LIGHT/" linked with GND, the backlight to be lit. 2. Need you to compress the screen and PCB tighter, might got loose after the delivery. 3 Use a 3.3V controller, otherwise the display could be quite vague. LCD Module:   Power supply voltage:2.7V-3.3V,5V is OK,but part of the screen becomes black when tested? Data interface level:2.7-5V? Backlight power supply voltage:highest 3.3V? Module size:43.6mm x 43.1mm(width X height)? Installation diameter:2mm? Backlight:White Document for Download:Data 1RST--------- reset? 2CE------------chip selection? 3DC-----------data/commands choice? 4DIN-----------serial data line? 5CLK------------serial Clock Spee 63.3V------------VCC? 7LIGHT--------- backlight control terminal? 8GND-----------power negative Features: 84 X 84 dot matrix LCD,can show 4 lines of characters Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting time. Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace. LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small Low power supply,the working current

Product features: Using HC - 06 from module 1, a core module, which leads to the interface includes VCC, GND, TXD, RXD, reserved LED state output pin, MCU can state whether the bluetooth is connected through the foot, from machine KEY pin is invalid 2, the led indicates a bluetooth connection status, twinkle said there was no bluetooth connectivity, Chang Liang said bluetooth is connected and turned on the port 3, backplane "3.3 V, the input voltage 3.6 ~ 6 V, current when the unpaired about 30 ma, matching after about 10 ma, no more than 7 V input voltage! 4, interface level 3.3 V, can be connected directly to all kinds of single chip microcomputer (51, AVR, PIC, ARM, MSP430, etc.), 5 V single chip can be connected directly, without MAX232 couldn/'t through MAX, clearing the effective distance of 10 meters, more than 10 meters is possible, but not to this distance connection quality After 6, pairing when full duplex serial port to use, do not need to know any bluetooth protocol, but supports only one