Controlled board light

This is an innovative product. Switching on and off lights are GPS CONTROLLED. lights are switched on at sunset time and switched off at sunrise time. Timings are based on GPS location.

This is the the lighting board for a shop you can change the banner and put on you shop name banner on it. This board is less used there are lights in side the board which are replaceable.

LOWEST PRICE IN   e b a y 10 TIMES MORE RELIABLE THAN OTHER CHINESE MODULE BEST FOR YOUR ROBOT / INDUSTRIAL  PURPOSE  /HOME & AUTOMATION 1 MONTHS REPLACEMENT WARRENTY IN CASE OF ANY PROBLEM DUE TO MANUFACTURING DIFFECT  HIGH QUALITY FR-4 BOARD Light Sensor For Arduino / PIC / AVR Description Module Features:    1, Using sensitive photosensitive resistance sensor    2,The comparator output signal is clean, good waveform, driving ability, more than 15mA.    3, With adjustable potentiometer to adjust the brightness of the light detection    4,The working voltage 3.3V-5V    5, DUAL OUTPUT form: DO digital switching outputs (0 and 1) and AO analog voltage output     6,A fixed bolt holes for easy installation    7, PCB Size: 3.4cm x 4.0cm   8, Using a wide voltage LM393 comparator Product wiring instructions:   1, VCC positive power supply 3.3-9V   2, GND power supply is negative   3, DO TTL switching signal output     4, AO analog output Please contact us for any doubt.Please give us positive feed back.Your feed back is very important for us. Happy to help you.We shipped our material within 2 working days after getting confirmation of payment. contact us- Mob:-     (From 10 AM to 9 PM)    Powered by Turbo Lister

Light Dimmer kit is a low cost dimmer circuit for adjusting the light brightness of incandescent, Halogen Lamp, Light Bulb upto 250 W. Input supply input: 230 VAC or 110 VAC Output: 250 W Triac controlled Onboard potentiometer (POT) for adjusting level Screw terminal connector for easy supply input / output connection Four mounting holes of 3.2 mm each PCB dimensions 40 mm x 34 mm DO IT YOUR SELF KIT (DIY) Kit contains components, PCB and Circuit Diagram

Laptop/Bluetooth Controlled Wireless Robot Robot Controlled By Laptop over Bluetooth Wireless Protocol. PACKAGE INCLUDES: 1) A ASSEMBLED Laptop/Bluetooth Controlled Wireless Robot 2) Pre- Built Windows Application By Robosoft Labs to drive the robot (Source code won't be provided due to copyright issue)   Laptop/Bluetooth Controlled Wireless Robot IS ASSEMBLED OF FOLLOWING LISTED ITEMS: 1) TWO L TYPE BO DC MOTOR (+5V TO +12V) 2) 2 CLAMPS 3) 1 CASTOR WHEEL 4) TWO WHEELS 5) L293D BOARD (MOTOR DRIVER BOARD) 6) CHASSIS 7) BLUETOOTH RECEIVER MODULE 8) 1 AVRDUINO/ARDUINO COMPATIBLE BOARD WITH AVR'S ATMEGA 8 IC 9) CONNECTING BURG WIRES 10) TUTORIAL GUIDE TEACHING HOW TO ASSEMBLE THE ROBOT FROM SCRATCH PARTS TO A Laptop/Bluetooth Controlled Wireless Robot. 11) PRE BUILT AND BURNT Laptop/Bluetooth Controlled Wireless Robot PROGRAM IN AVRDUINO ATMEGA 8 IC 12) NUT AND BOLTS. Points to be noted: 1) This Laptop/Bluetooth Controlled Wireless Robot is ASSEMBLED BY PRE-FABRICATED PARTS. 2)  Laptop/Bluetooth Controlled Wireless Robot CHASSIS is made of PLY WOOD 3) PROGRAM CODE or HEX FILE WONT BE PROVIDED Due to Copyright Issue. 4) Power Supply for Robot: Please use Only +9V battery supply (Batteries not Included as it can't be shipped)   5) Color of Components used may vary according to availability.                        FOR ANY QUERIES OR DOUBT PLEASE CONTACT US BEFORE ORDERING                                                                       E-MAIL:                                                                       MOBILE: +91- Regards, ROBOSOFT LABS                                                                  

ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT T his Wireless robot is control by ANDROID APP with the help of BLUETOOTH Wireless Protocol. This ANDROID APP also Supports VOICE COMMANDS to drive the robot too. PACKAGE INCLUDES: 1) A ASSEMBLED ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT 2) Pre- Built ANDROID APP By Robosoft Labs to drive the robot. (APP source code/program won't be provided due to copyright issue) ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT IS ASSEMBLED OF FOLLOWING LISTED ITEMS: 1) TWO L TYPE BO DC MOTOR (+5V TO +12V) 2) 2 CLAMPS 3) 1 CASTOR WHEEL 4) TWO WHEELS 5) L293D BOARD (MOTOR DRIVER BOARD) 6) CHASSIS 7) BLUETOOTH RECEIVER MODULE 8) 1 AVRDUINO/ARDUINO COMPATIBLE BOARD WITH AVR'S ATMEGA 8 IC 9) CONNECTING BURG WIRES 10) TUTORIAL GUIDE TEACHING HOW TO ASSEMBLE THE ROBOT FROM SCRATCH PARTS TO A ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT. 11) PRE BUILT AND BURNT ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT PROGRAM IN AVRDUINO ATMEGA 8 IC 12) NUT AND BOLTS. Points to be noted: 1) This ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT is ASSEMBLED BY PRE-FABRICATED PARTS. 2)  ANDROID/VOICE/BLUETOOTH Based Wireless Controlled ROBOT CHASSIS is made of PLY WOOD 3) PROGRAM CODE or HEX FILE WONT BE PROVIDED due to COPYRIGHT ISSUE. 4) Power Supply for Robot: Please use Only +9V battery supply (Batteries not Included as it can't be shipped) 5) Color of Components used may vary according to availability. 6) Mobile phone shown is not included

Other Items Feedbacks About Us Contact Us Add To Favorites New 6 Pc Complete DTMF (Mobile) Controlled Robot Kit  with L298Motor Driver Board. Kit Contains DTMF Driver Board L298 Motor Driver Board FRC Cable Crocodile Clip-DC Jack Cable Microphone Input Cable 3.5mm Stereo Extension Cable  (Doesnt Contain Motors and other ACCESSORIES) + + DTMF (Mobile) Controlled Robot Kit (with L298 Board) for controlling 2 motors

Description Single Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has ONE relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a Single channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description Four Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has FOUR relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a 4 channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

1 Channel Relay Board Module For PIC AVR DSP ARM Arduino AVRDuino This is a  1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino, AVRDuino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).   Features: 1 -Channel Relay interface board Equiped with high-current relay, Rating are as follows: 1) 7A-250 V AC 2) 10A-125V AC 3) 12A 120V DC 4) 10A 28V DC Standard interface that can be controlled directly by microcontroller (Arduino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)   Has the fixed bolt hole and easy installation Small board PCB size R elay status indicator LED (red) Weight ： 10 0 g   Module interface specifications (3 wire)   1. External 12V 2. GND external GND 3. 1N interchange relay control interface (Control by 3.3V or 5V Logic)   Package included:   1 Channel Relay Board Module Note: Relay and Component Colors varies as per availability.

This is a  4-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino, AVRDuino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features: 4-Channel Relay interface board Equiped with high-current relay, Rating are as follows: 1) 7A-250v AC 2) 10A-125V AC 3) 12A 120V DC 4) 10A 28V DC Standard interface that can be controlled directly by microcontroller (Arduino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)   Has the fixed bolt hole and easy installation Small board PCB size four ways of relay status indicator LED (red) Weight ： 15 0 g Module interface specifications (6 wire) 1. External 12V 2. GND external GND Package included: 10 x  4 Channel Relay Board Module Note: Relay and Component Colors varies as per availability.

This is a  4-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino, AVRDuino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features: 4-Channel Relay interface board Equiped with high-current relay, Rating are as follows: 1) 7A-250v AC 2) 10A-125V AC 3) 12A 120V DC 4) 10A 28V DC Standard interface that can be controlled directly by microcontroller (Arduino, , AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)   Has the fixed bolt hole and easy installation Small board PCB size four ways of relay status indicator LED (red) Weight ： 15 0 g Module interface specifications (6 wire) 1. External 12V 2. GND external GND Package included: 1 x  4 Channel Relay Board Module Note: Relay and Component Colors varies as per availability.

Application: RF Controlled Robot Using RF Encoder and Decoder Module: Robosoft Labs RF Encoder & Decoder Interfacing board with HT12D & HT12E IC chips. Features: Easy interfacing with the RF modules, using the female headers for placing the modules. Breakout pins for connecting to the microcontroller. switch for manual Testing Status LED and switch button. Small size, high quality PCB.  Package Contents: 1 piece of RF encoder and decoder board with HT12E/HT12D IC chips. Applications: 1) RF Controlled Robot Using RF Encoder and Decoder Module: Robosoft Labs 2) Home Automation 3) Switch On/Off lights and other home appliances through with RF

Package Contents 1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has one (1) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by transistor BC547 hence your input device, such as Arduino, is protected from relay circuit. There is free wheeling diode which will further protect your microcontroller from relay kick back. This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Free wheeling diode to protect your microcontroller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided