Enc28j60 ethernet interface board

ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC STM32 Product Description: The ENC28J60 Ethernet Module utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20MHz. Specification: ENC28J60 Ethernet chips, SOP28 package SPI Interface 2X5 connector, can be easily mounted with the MCU Power indicator Single Supply: +3.3 V PCB size: 55x36 mm Technical Details:    This module is based on resistive voltage divider design principles, It is capable of reducing the voltage of the input terminal connection five times ●       You can use a 5V maximum voltage on the ADC side of the module so which allows for a maximum of 25V on the input side ●       If 3.3V is used, the input voltage must not exceed 16.5V ●       Because AVR chips use 10 bit ADC, the maximum resolution of this module is 0 ●       00489 V (5V / 1023), so the voltage detection module detects minimum input voltage is 0.00489VÁ 5 = 0.02445 ●       Input voltage range: DC0-25V ●       Voltage detection range: DC0.02445 V - 25V ●       Voltage analog resolutions: 0.00489V ●       DC Input: positive terminal connected to VCC, GND negative pole ●       Output interface: "+" then 5 / 3.3V, "-" then GND, "s" then the AD pin Package Included: 1 x  ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC STM32 Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Description: This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz. It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed. Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip. Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network. Features: Microchip ENC28J60 Ethernet Chip supporting Microchip s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support. Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project Suitable for 3.3V Interface LAN connector with build in transformer Link and Activity LED's on Ethernet connector 8 pin standard interface connector with spacing of mm) row pins IEEE Compatible with Integrated MAC and 10Base-T PHY Fully Compatible with Base-T Networks Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Padding and CRC Generation Programmable SPI Interface with Clock Speeds Up to 20 MHz Application: Remote control and monitoring. Data capture and logging Industrial Automation Building Automation Appliance remote management Robotics Microcontroller Research and Development TCP/IP Research and Development Specification: Operating Voltage: +3.3V DC Current Consumption: 180mA average Pin Spacing: mm) Board Size: 68x22mm We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

This is a great module if you want to add an internet connection to your microcontroller projects. The board is based off of the popular ENC28J60 IC and handles most Ethernet network protocol requirements. Ethernet LAN Module for PIC/Atmel AVR/Arm ENC28J60-I/SO Ethernet chip module Network Interface: HanRun HRA Supply Voltage: 3.3 V Size: 50mm x 33mm x 18mm

Description The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.. The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming in Arduino ). An SD card library is not yet included in the standard Arduino distribution. Arduino communicates with both the W and SD card using the SPI bus (through the ICSP header). This is on digital pins , and 13 on the Duemilanove and pins , and 52 on the Mega. On both boards, pin 10 is used to select the W and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W or the SD card, but it must be kept as an output or the SPI interface won't work. Note that because the W and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W, set digital pin 10 as a high output. The shield provides a standard RJ45 ethernet jack. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

HLK-RM04 Serial Uart to Ethernet Switch WIFI Module with antenna and HLK-RM04 UART to WIFI  Module Test Base Board   Description Product features. 
 1). UART to WIFI Wireless Module ， UART to Ethernet Module ， Ethernet to WIFI Module ， UART server module ， Make your Serial Device connected to the Internet easily. Double Data Rate All transparently. Guarantee the highest limit of Usability and Compatibility. 
 2). The module integrated m adaptive Ethernet interface.The highest baud rate up to Kbps of the serial communication.and the highest rate of TTL serial port is 500KBPS. 
 3). Each module

Cubietruck Cubieboard3 Cortex-A7 Dual-Core 2GB RAM/8GB Flash with Wifi + Bluetooth Cubietruck is also named Cubieboard3. It is a SbC built on top of Allwinner  A20  SoC, just like Cubieboard2. It is however enhanced with some features, such as 2GB memory, VGA display interface on-board, Gigabit Ethernet, WiFi+BT on-board, support for Li-battery, RTC and SPDIF audio interface. Specifications AllWinnerTech SOC A20, ARM® Cortex™-A7 Dual-Core, ARM® Mali400 MP2 Complies with OpenGL ES GB DDRMHz (960MTPS) Internal Storage: 8GB NAND Flash HDMI & VGA P display output on-board 10M/100M/1G Ethernet Wifi+BT wireless connection with antenna on-board SATA 2.0 interface support 2.5' HDD, (only for 3.5' HDD, need another 12V power input) Storage solution: NAND+MicroSD or TSD+ MicroSD or 2*MicroSD 2 x USB HOST, 1 x OTG, 1 x Toslink (SPDIF Optical), 1 x IR, 4 x LEDs, 1 Headphone, 3 x Keys Power: DC5V @ 2.5A with HDD, support Li-battery & RTC 54 extended pins including I2S, I2C, SPI, CVBS, LRADC x2,UART, PS2, PWMx2, TS/CSI, IRDA, LINEIN&FMIN&MICIN, TVINx4 with 2.0 pitch connectors PCB size: 11cm *8cm*1.4mm, very suite for installing a 2.5' HDD Package Includes Main board x 1 Simple case x 1 OTG cable x 1 Power Cable Sata Cable

Description: The  Internet of Things  (IoT) is the interconnection of uniquely identifiable embedded computing devices within the existing Internet infrastructure. Web shield is a smart communication shield for controlling and monitoring embedded application via internet.Internet is the media and economic way for communication between anywhere from to geographical location.This shield is compatible with Arduino open source and make easy way for customized application dev elopment.This shield has got four relay 10AMP. The board by ULN IC. The board works on 5V. IoT Web Shield - Smart Internet Application Development Kit Features: IEEE compatible. Supports Full and Half-Duplex modes. Integrated MAC and 10Base-T PHY SPI Interface with Clock Speeds Up to 20 MHz. With this Ethernet Shield, your Arduino board can be connected to internet. Stackable by accepting prototype shield or any other boards with Arduino compatible interface. LED indication for relay & power supply.  Design based on highly proven IC ULN as driver.  DC-DC Converter. High quality PCB FR4 Grade with FPT Certified.   IoT Web Shield - Smart Internet Application Development Kit  I/O Connection:  IoT Web Shield - Smart Internet Application Development Kit Circuit Diagram: Development Kit Circuit Diagram Screenshots:        IoT Web Shield - Smart Internet Application Development Kit Documents and Codes: Arduino Code Package Contains: IoT Web Shield + 2 pcs screw shield.  Note  : The aurdino

BRAND NEW LGA 775 INTEL G31 CHIPSET WINSONIC Motherboard + DDR2 2GB RAM +CORE 2DUO PROCESSOR 2.4 or higher GHZ + CPU FAN 1 year complete warranty.Product DescriptionChipset: Intel 945 FSB Bus: FSBMHz host bus Frequency Memory type: 2 x 240pin DDRMHz support dual channels, max up to 4GB Supported Processor: p4/ Dual Core/Core 2 Duo up to processor bus which is 775 socket I/O Ports: HDD: 2 x SATAII interface, 1 x IDE Audio: Realtek ALC6XX HD audio codec, 6 channel audio solution Keyboard/Mouse: 2 x mini-DIN port for PS/2 Keyboard and Mouse LAN: 1 x MB ethernet controller USB: 4 x USB 2.0 Expansion: 1 x PCI-Express x16, 2 x PCI COM Port: 1 x Parallel port: 1 x Display Graphics: Integrated Intel GMA X Graphics Controller, MAX up to 384MB video memory VGA: 1 x VGA Power supply: 24Pin+12V 4Pin ATX Main board dimension: MATX 16.8cm x 23.8cm CORE 2 DUO - Processor -2.0 OR Higher GHz RAM DDR2 2 GB(1+1) - Brand New - Sealed Pack CPU FAN included as a Bonus.