Mega uno based

Arduino MEGA UNO Based HC05 Bluetooth Module: Description: This module can be set to a transmitter or receiver, transmitter could pairing with receiver, receiver and receiver or transmitter and transmitter can't communication between, receiver could pairing with computers and cell phone bluetooth, when buying, the default for receiver.   1. It is HC-05. 2. Use the CSR mainstream bluetooth chip, bluetooth V2.0 protocol standards.       3. Module working voltage 3.3 V.       4. Potter default rate of , the user can be set up.       5. The core module size: 28 mm x 15 mm x 2.35 mm.       6. Working current: matching for 30 MA, matching the communication for 8 MA.       7. Dormancy current: no dormancy.       8. Used for GPS navigation system, water and electricity gas meter reading system.       9. With computer and bluetooth bluetooth adapter, PDA, seamless connection equipment Works with any USB Bluetooth adapter. Easy to use and completely encapsulated. This module includes key interface and state interface compared with Smart Bluetooth Module Baseboard. The Bluetooth Module Baseboard can be compatible with master mode,slave mode and both master-slave mode. Works for Bluetooth TTL transceiver module which allows your target device to both send or receive the TTL data. The key interface on the baseboard is the master mode button and can be controlled by high level from external MCU, then this module will search again automatically. This module power supply input is 3.6~6V, Please be careful that it should be not more than 7V. The STATE interface on the baseboard is interface for LED STATE output feet, when bluetooth module don't not connected with other device and then output pulse, when bluetooth module connected with other device and then output high level, and the MCU will judge the state, then this module will search again automatically. Commercial Series: Bluetooth module board Series With LED indicator light, use 150mA and 3.3V regulation chip. With VCC.GND.TXD.RXD foot for the Bluetooth With "Re-seach" button(ON/OFF/WAKE foot for it, external MCU outinput "High level" can control module to re-seach) Compatible with bluetooth master module".slave module"or master-slave(whole) module. Input voltage: 3.3~6V Size: 1.55cm*3.98cm Note: input power supply 3.3~6V, Prohibit more than 7V No "Automatically prevent power supply peversing func", so please correctly connect power supply       We advise to install "Bluetooth master module"       The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse"; when bluetooth "connected", output "High level", we can determine the states from "MCU"       If only the board, No any "Bluetooth Function  ____________________________________________________________________________________________________________________________________ Package includes: 1 x Interface Base Board Module For Further Details: Email:

Arduino MEGA UNO Based HC05 Bluetooth Module: Description: This module can be set to a transmitter or receiver, transmitter could pairing with receiver, receiver and receiver or transmitter and transmitter can't communication between, receiver could pairing with computers and cell phone bluetooth, when buying, the default for receiver.   1. It is HC-05. 2. Use the CSR mainstream bluetooth chip, bluetooth V2.0 protocol standards.       3. Module working voltage 5 V.       4. Potter default rate of , the user can be set up.       5. The core module size: 28 mm x 15 mm x 2.35 mm.       6. Working current: matching for 30 MA, matching the communication for 8 MA.       7. Dormancy current: no dormancy.       8. Used for GPS navigation system, water and electricity gas meter reading system.       9. With computer and bluetooth bluetooth adapter, PDA, seamless connection equipment Works with any USB Bluetooth adapter. Easy to use and completely encapsulated. This module includes key interface and state interface compared with Smart Bluetooth Module Baseboard. The Bluetooth Module Baseboard can be compatible with master mode,slave mode and both master-slave mode. Works for Bluetooth TTL transceiver module which allows your target device to both send or receive the TTL data. The key interface on the baseboard is the master mode button and can be controlled by high level from external MCU, then this module will search again automatically. This module power supply input is 3.6~6V, Please be careful that it should be not more than 7V. The STATE interface on the baseboard is interface for LED STATE output feet, when bluetooth module don't not connected with other device and then output pulse, when bluetooth module connected with other device and then output high level, and the MCU will judge the state, then this module will search again automatically. Commercial Series: Bluetooth module board Series With LED indicator light, use 150mA and 3.3V regulation chip. With VCC.GND.TXD.RXD foot for the Bluetooth With "Re-seach" button(ON/OFF/WAKE foot for it, external MCU outinput "High level" can control module to re-seach) Compatible with bluetooth master module".slave module"or master-slave(whole) module. Input voltage: 3.3~6V Size: 1.55cm*3.98cm Note: input power supply 3.3~6V, Prohibit more than 7V No "Automatically prevent power supply peversing func", so please correctly connect power supply       We advise to install "Bluetooth master module"       The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse"; when bluetooth "connected", output "High level", we can determine the states from "MCU"       If only the board, No any "Bluetooth Function  ____________________________________________________________________________________________________________________________________ Package includes: 1 x Interface Base Board Module For Further Details: Email:

UNO R3 Development Board For Arduino Compatible with USB Cable This UNO R3 BOARD is a 100% compatible derivative of current R3 Arduino UNO's This is an Arduino Clone based on current open source hardware We are not affiliated with Arduino.cc IMPORTED HIGH QUALITY Delivery Time: 3-7 WORKING DAYS 100% TESTED & SATISFACTION GUARANTEED CASH ON DELIVERY AVAILABLE Buy Original Arduino UNO R3 from http://store.arduino.cc/index.php?main_page=product_info&cPath=11&products_id=195 Download Arduino IDE & Drivers: http://arduino.cc/en/Main/Software No need to install any additional driver

UNO R3 Development Board For Arduino Compatible with USB Cable This UNO R3 BOARD is a 100% compatible derivative of current R3 Arduino UNO's This is an Arduino Clone based on current open source hardware We are not affiliated with Arduino.cc IMPORTED HIGH QUALITY Delivery Time: 3-7 WORKING DAYS 100% TESTED & SATISFACTION GUARANTEED Buy Original Arduino UNO R3 from  http://store.arduino.cc/index.php?main_page=product_info&cPath=11&products_id=195 Download Arduino IDE & Drivers:  http://arduino.cc/en/Main/Software No need to install any additional driver

This MEGA BOARD is a 100% compatible derivative of current R3 Arduino MEGA This is an Arduino Clone based on current open source hardware We are not affiliated with Arduino.cc IMPORTED HIGH QUALITY FAST SHIPPING WITHIN 3-7 WORKING DAYS 100% TESTED & SATISFACTION GUARANTEED CASH ON DELIVERY AVAILABLE Buy Original Arduino UNO R3 from  http://store.arduino.cc/index.php?main_page=product_info&cPath=11&products_id=195 Download Arduino IDE & Drivers:  http://arduino.cc/en/Main/Software No need to install any additional driver

Package Contents 1 x UNO R3 ARDUINO COMPATIBLE DEVELOPMENT BOARD 1 x FREE USB Cable "COLOR OF CABLE AND LOGOS ON BOARD MAY BE DIFFERENT FROM THE IMAGES SHOWN. IMAGES ARE FOR ILLUSTRATION PURPOSES ONLY" "EXTERNAL POWER SUPPLY IS NOT INCLUDED & HAS TO BE PURCHASED SEPARATELY" Buy Original Arduino UNO R3 from  www..in/itm/ Download Arduino IDE & Drivers:  http://arduino.org/downloads This is the new Fully 100% compatible derivative version of Uno R3 based on current open source hardware.  In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included

The  Uno R3 Arduino is a microcontroller board based on the Arduino ATmega328 (high speed microprocessing controller) Note: Arduino UNO R3 Compatible Board ATmega328P ATmega16U2 with USB cable  is designed based on Arduino's Open Source Schematics and is 100% Arduino IDE Compatible. We Pack each item

1 x UNO R3 MEGA328P ATMEGA16U2 board                       +  1 x USB cable  + 1 Plastic Carry Box  Product Description: 100% Brand New,  It is based on  MEGA328P Chip with 16U2 (UNO R3) feature,high quality clone. ATMEGA16U2 MEGA328P  UNO R3 Color of USB Cable: blue Transparent Plastic Carry Box   Package Include: 1 x UNO R3 MEGA328P ATMEGA16U2 board +  1 x USB cable + 1 Plastic Carry Box   Performance description: Digital I/O Digital input/output terminal, a total of 0 ~ 13. Analog I/O Analog input/output terminal, a total of 0 ~ 5. Support the ISP download function. The input voltage: when connected to the computer USB without external power supply, external power supply 5 v ~ 9 v dc voltage input. Output voltage: 5 V dc voltage output and 3.3 V dc voltage output. Using Atmel Atmega328 microprocessor controller. Payment Options:   Payment by PaisaPay only, Safest payment mode on .  Terms and Conditions: Orders are expected to be shipped within 2 days of receiving cleared payment  excluding holidays.. Shipping details will be emailed to you after the item is shipped and then you can track your order. No Address change entertained once the order is placed. Please refuse to accept the package from courier if its

www.hitroncomponents.com Package Contents   1 x UNO R3 ARDUINO COMPATIBLE DEVELOPMENT BOARD 1 x FREE USB Cable   "EXTERNAL POWER SUPPLY IS NOT INCLUDED & HAS TO BE PURCHASED SEPARATELY"   Buy Original Arduino UNO R3 from  http://store.arduino.cc/index.php?main_page=product_info&cPath=11&products_id=195 Download Arduino IDE & Drivers:  http://arduino.cc/en/Main/Software For bulk order get special price Contact Details   Have any queries, Feel free to contact us anytime   Ph: +91-   or email us:   or contact us through by clicking "Ask seller a question"   Feedback Details   In case, you are not satisfied with the item or have any questions or complaints, please contact us before leaving a Feedback.   Leaving Negative or Neutral Feedback will not solve a problem,   We are always willing to solve the problems of buyers.   "Your feedback is very important for us to grow our business on , so please do leave positive feedback"       The Arduino Uno is a microcontroller board based on the  ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards

W ethernet shield for arduino UNO mega with micro SD slot Ethernet shield w for uno mega diecimila duemilanove Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.     Product Summary arduino w:   The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W Ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield.     Description arduino Ethernet w:             The Ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top             The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming

W ethernet shield for arduino UNO mega with micro SD slot Ethernet shield w for uno mega diecimila duemilanove     Product Summary arduino w:   The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W Ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield.     Description arduino Ethernet w:               The Ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top               The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming

Description Wiznet W Ethernet Shield for Arduino Uno & Mega with SD card slot                                      Description: Description: The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the  Ethernet library  to write sketches which connect to the internet using the shield. The ethernet shield connects to an  Arduino board  using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.. The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming

Description The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.. The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino UNO and Mega (using the Ethernet library coming in Arduino ). An SD card library is not yet included in the standard Arduino distribution. Arduino communicates with both the W and SD card using the SPI bus (through the ICSP header). This is on digital pins , and 13 on the Duemilanove and pins , and 52 on the Mega. On both boards, pin 10 is used to select the W and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W or the SD card, but it must be kept as an output or the SPI interface won't work. Note that because the W and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W, set digital pin 10 as a high output. The shield provides a standard RJ45 ethernet jack. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description This is a Ethernet shield based on the Wiznet W ethernet chip,compatible with  Arduino Ethernet Shield,added support to Arduino Mega. The different between with Arduino Ethernet Shield just  Layout  of Ethernet port location. It is based on the Wiznet W ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the  Ethernet library  to write sketches which connect to the internet using the shield. The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Duemilanove and Mega (using the Ethernet library coming

Overview The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards

Arduino uno r3 development board with ATmega328p CH340G Arduino clone based on current open source hardware Arduino uno Atmega 328p smd ideal for prototyping Order multiple quantity or multiple items from 4d_innovations to save on shipping cost.   Product Summary arduino uno: ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz         Features of arduino uno: ·         Replaced the expensive 16u2 with CH340G chip to avoid the driver compatibility problem which was found on some win7/win8 OSes. ·         Increased the extra pin holes to facilitate the use of DuPont line cables, with some extra useful pins. ·         Extra 3x4 pin holes, next to ICSP connector, which includes Tx, Rx, 5v, 3.3v, ground, SDA and SCL.    ·         All the rest features are kept the same as the official version   Driver installation and usage procedure: · Install   CH340G driver  . ·     Install   Arduino IDE   ß   (click here) ·     Connect the board to computer. ·     Launch Arduino IDE, select board as “arduino uno” ·     Select the com port OS created for the card(control panel   à   device manager) ·     Open basics   à   blink sketch and upload. ·     If you find any difficulty you can contact us, contact details are given below.   Factory Testing Procedure for arduino uno Atmega328p: We will make sure that we have tested the product with following procedure before shipment ·   We have uploaded blink program with 2 second blinking rate of LED ‘L’ instead of 1second default rate. ·   You can check it at the time of receipt of the product. Just connect it to the USB port of any device and the ‘L’ LED will blink at the rate of 2 second.   Package Include arduino uno: ·   1 x   arduino uno development board ·   1 x   USB cable ·   A plastic container box.   Shipping Details:     And for remote locations we prefer Indian speed post   Feedback: ·         In case you find any problem

PRODUCT DETAILS: Arduino UNO R3 Compatible Board ATmega328P ATmega16U2 with USB cable DESCRIPTION This is a Compatible board for Arduino uno r3, not original This UNO is a 100% compatible derivative of current R3 Arduino UNO The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller;simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Features:- Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

The Freeduino is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Before connecting the Freeduino, CP Driver installation would be required.   Got to link below http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx Or google CP driver download. ------------àSelect as per your Operating system and download the driver------------àUnzip the file on desktop ------------àConnect the UNO with USB Cable given to your computer------------àDevice Manager will display Unknown device for the UNO (CP IC). Right click on the same and click on update driver. Give path as desktop. Wait till driver is installed. ------------àYour CP Driver is installed and Uno is ready for use.

DESCRIPTION MatLogix Arduino Uno Board with Universal Shield The ARDUINO Board (ATMEGA 8-L) is a microcontroller board based on the ATmega 8-L. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8 up to programmed as a USB-to-serial converter. Universal Shield: Features: A monolithic integrated, high voltage, high current, 4-channel driver Using this chip you can use DC motors and power supplies of up to 36 V, so that some pretty big motors and the chip can supply a maximum current of 600mA per channel Also known as a type of H-Bridge, which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping LDR (light Sensor) for detecting the intensity of light. On board Regulated Power Supply 5v,12v supplys A Serial Port DC Power Supply Connector(12v Dc) LCD display 2x16Character Extra Vcc and Gnd Pins from which you can connect different devices. Potentiometer to set the light intensity of LCD Screen. Reset Switch to reset the arduino board. Slot for TSOP sensor. Kit Content: 1 x Arduino Uno Board 1 x 16x2 LCD (Female) 1 x L293D IC 1 x LDR 1 x USB Cable We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Product Description:   The Freeduino is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Before connecting the Freeduino, CP2102 Driver installation would be required. Got to link below http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx Or google CP2102 driver download. ------------>Select as per your Operating system and download the driver------------>Unzip the file on desktop ------------>Connect the UNO with USB Cable given to your computer------------>Device Manager will display Unknown device for the UNO (CP2102 IC). Right click on the same and click on update driver. Give path as desktop. Wait till driver is installed.------------>Your CP2102 Driver is installed and Uno is ready for use.   Contact: Contact us on Messaging for any Queries. We offer discounts for bulk orders on   Feedback: We provide good quality products & all products are QC checked before dispatch. We strive for 100% positive feedback for our orders. Providing Negative feedback will not solve anything feel free to write to us on messaging service. Feel Free to contact us on +91 7738961235   Shipping: Shipping is done only through Powership. Logistics partners include – Bluedart DHL, Dotzot, Aramex, Fedex.  

Package Contains 1XArduino Uno R3 1X Usb Cable for Arduino The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins(of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz  ceramic resonator, a USB connection,a power jack, an ICSP header, and a reset  button. It contains everything needed to support the microcontroller;simply connect  it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get  started. Features:-  Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz

Arduino UNO (Q021) The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. Microcontroller ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328) EEPROM 1 KB (ATmega328) Clock Speed 16 MHz Length 68.6 mm Width 53.4 mm Weight 25 g