Pcb signal relays

Relay SPDT 6V 10A - PCB mount Branded High Quality Relays SPDT 6V 10A PCB Relay Description: Relay SPDT 6V 10A - PCB mount JQC-3FC(T73) DC6V(can be used with 5V). Relays can be used to control both AC and DC appliance which comply with the output rating mentioned below. Relays are used

Miniature PCB 6V Power Relays 10A 250VAC.     Contact Material:   AgSnO alloy Contact Current rated:   10A Mounting Type:   PCB through Hole Enclosure:   Sealed Contact Type:SPDT Coil Voltage: 6V Contact Resistance:100mOhm The Specification,Colour may change  

Universal Stereo  Preamplifier PCB with Tone Control        Build your own high end stereo control preamplifier.      This PCB has been designed for audiophils who enjoy un distorted music. Glass epoxy, Green masked, Lead tinned pads & Legend printed bare PCB. Volume / Balance / Bass /Treble / Balance / Loudness / Source select switch. Switchable Input signal selector for 2 sources (CD / Aux) 2 Operational amplifiers

Preamplifier PCB for 5.1 channels home theature.   Universal multi channel preamplifier. Bare PCB. Glass epoxy, Green masked, Lead tinned Pads and Legend printing Variable gain catering to almost all audio amplifiers. Better audio signal tracking for minimum interference pick up. Provisioned to use SMD IC's (TLO74) for compact and less noise. High bandwidth and dynamic range. All channels gain can be set individually. Works off dual 10 to 15 Volts DC. Instructions and wiring laypout

Sound Sensor High Sensitivity Sound Detection Module for Arduino Features: 1.84 X 84 dot matrix LCD, can show 4 lines of characters 2.Use serial interface communicate with the master processor, the number of interface signal line reduced greatly, only 8 signal lines including power and GND. 3.Support different types of MCU, such as the arduino, AVR, SPI, MCS51 and so on. 4.Transfer rate up to 4Mbps, can full speed write display data without waiting time. 5.Can use the conductive glue to connect the module with the printed board, without cables. The metal hooks on the module can fix the module on the printed board, which is very easy to install and replace. 4.LCD controller/driver chip has been bound to LCD chip, the volume of LCD is small 5.Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode Connections: 1.RST--------- reset 2.CE---------- chip selection 3.DC---------- data/commands choice 4.DIN--------- serial data line 5.CLK--------- serial Clock Speed 6.3.3V-------- VCC 7.LIGHT------- backlight control terminal 8.GND--------- power negative Specifications: 1.For Nokia 5110 3V-5V 2.Module size: 45.2mm x 43.1mm Package included: 1x LCD Module for Nokia 5110 Feedback:- Dear all,customer satisfaction is very important to us and our feedback rating reflects this satisfaction. Please do not leave negative feedback,if there is any problem,please contact us,we will do our best to provide the best service! If you are satisfied with the purchase and our service,please take a minute to give us a positive feedback. Please leave us 5 star feedback. For Customer support call / Whatsapp   0-76-9885-9005 किसी भी प्रकार की जानकारी या फिर मदद के लिए कॉल या W hatsapp  कीजिये    0-76-9885-9005 For bulk orders call or whatsapp  0-76-9885-9005 Shipping Via  FEDEX  & INDIAN POST  As per Available Location. Note:  IF ANY Confusion? Call us / Whatsapp    So please ask to seller before purchase. Thank You.

Description Single Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has ONE relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a Single channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

Description Four Channel 12V Relay Board: A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal. The board has FOUR relay which works on 12V but the input signal can come directly from microcontroller output working at 3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by the RED Led. This is a 4 channel relay board operates on 12V. Can be used directly to control 240V power appliance from most of the microcontrollers and other control system circuits. Perfect for switching 240V appliances like lights, fans, etc. The board has a high quality relay, which can handle a maximum of 10A @ 120V or 7A @ 240V AC. Each Relay has three connections - Common - C, Normally Open-NO, Normally Closed-NC brought out to 3 pin screw terminals which makes it easy to make and remove connections. The board has a power indication and a relay status LED to ease debugging. Power input and relay control signals are brought to header pins on the board. Features: Selectable Port Input Mounting Supports Provided Relay Switching Output Suitable for 7A @ 250Vac or 10A @ 120Vac LED Indication of Relay ON. Power Indication LED. Direct input from 3-5V Microcontroller for relay control. Output terminal for relay contacts. Provision of male header for wire connection. Powered from external 12V or from male header. Note: It is important that microcontroller share ground with relay board along with other control signals else it will not able to control relay. We deliver these products In Kirti Nagar, Connaught Place, Patel Nagar, Bhagirath Palace, Karol Bagh, Nehru Place, Laxmi Nagar, Lajpat Nagar, Pitampura, Khan Market, Paharganj, Sarojini Nagar, Noida, Vaishali, Faridabad, Ghaziabad, Gurgaon and Delhi NCR. For more information, please contact: MatLogix Technologies Pvt. Ltd. RZ- A/59, Second Floor, Street No. 4, Near Hotel The Grace, New Delhi - Call: , E-mail id: Visit: http://matlogix-technologies.shopclues.com/

4-channel relay control board module with optocoupler, 4 way relay module for arduino 4-channel relay output modules, relay output contacts 250A 10A. Input IN1, IN2, IN3, IN4, the signal line LOW effective. VCC, GND power input, can relay a separate power supply relay power input of JD-VCC. Uses: support all MCU control. the industrial sector PLC control smart home control Module parameters: Size: 75mm (length) x 55mm (W) x 19.3mm (height); Weight: 58g; PCB Color: Blue; board four weeks with four screw holes, hole diameter 3.1mm, easy to install and fixed; Relay selection of quality loose music relays, SPDT. A common terminal, a normally open, one normally closed terminal; optocoupler isolation, good anti-jamming; Low pull, high release. Energisation status indicator light, release status LED is off; VCC for the system power, JD_VCC for the relay power. Default hair 5V relay, plug the jumper cap to; Relay Maximum output: DC 30V/10A, AC 250V/10A Wiring: VCC: positive power supply system GND: System power supply negative IN1 – IN4: relay control ports Shipment Details We ship the item from our side on the same day or on the next working day after receiving payment. Any Taxes or Octroi charged

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc....   ***(Work with All Analog/Digital circuits with signal from 3V to 15V) *** Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 3.3v and 5v micro controller  (Check Other Listings  for  1.8V-5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 3V to 16V(1.5V to 16V for 1.8V logic) with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 3.3V and 5V micro controllers/Digital (1.8V Version also available Please Check My other Listings).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

1 x Single Channel 12V Relay Board Module Product Overview Relay board module is used for controlling higher current loads from your Digital, Microcontroller,PC parallel port or Arduino Uno Etc... This board has 1 on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. There is free wheeling diode which will further protect your micro controller from relay kick back. and Reverse Supply protection included for Accidental supply reverse connection This is a 12V 1-Channel Relay interface board which can be controlled directly by All Digital and All micro controllers,  such as Arduino, AVR, PIC, MSP, COP8, ST,ARM, Etc.... ***(Work with All Analog/Digital circuits with signal from 1.5V to 15V) ***   Features: - Power supply Reverse Protection (useful to provide protection against accidental reverse polarity) - Improved Spike reduction(reduce System hangs when Operate Relay) - Work with All 1.8V,3.3v and 5v micro controller  (Check Other Listings  for  3.3V,5V Version) - Equipped with high-current relay 7A@250VAC / 10A@28VDC  - Control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals  for quick and easy connection - Free wheeling diode to protect your micro controller. - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicator to indicate the relay ON/OFF status. - Mounting holes provided ***ALL Modules are tested with Signal input 1.5V to 16V with VCC 16V*** Pin Details 12V    - 12V power supply for Relay GND   - Ground Signal - Control Signal for Relay On/Off, Work with 1.8V, 3.3V and 5V micro controllers/Digital).       Have any queries, Please contact through by clicking "Ask seller a question" Powered by Turbo Lister

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has eight (8) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 8-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four (4) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by ULN IC hence your input device, such as Arduino, is protected from relay circuit and IC will further protect your microcontroller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - ULN IC used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Features The is a 5V 8-Channel Relay interface board with optocoupler which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSC, and so on. Can be powered by 5V DC Source (From USB) Or from the same source powered to Arduino or any other micro controller. Equipped with high-current relay 10A@250 VAC / 10A@28 VDC which can control both AC and DC appliances such as Solenoids, Motors, lights, fans etc High quality screw terminals provided for each relays (C, NC, NO) for quick and easy connection Interfaced with optocouplers to isolate relays & protect your microcontroller. Input Signal Pin connected to Burg stick for easy accessibility LED Status indicators to indicate the relay ON/OFF status. Dimension: 13.4 x 5.3 x 1.7cm (5.28 x 2.09 x 0.67in) Mounting holes provided Shipping contents 1 x 5V DC 8 Channel relay board as shown

Product Overview Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has two (2) on-board relay which can switch up to 7Amps. Relays terminals (C, NC, NO) are accessible through screw terminals which makes wiring up the board very easy. The relay is safely driven by Transistor hence your input device, such as Arduino, is protected from relay circuit and Transistor will further protect your micro-controller from relay kick back. This is a 12V 4-Channel Relay interface board which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on.  - BC 547 Transistor used to drive Relays (better than Transistor Drive Circuits) - Equipped with high-current relay 7A@250VAC / 10A@24VDC  - It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc - High quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection - Input Signal Pin connected to Burg stick for easy accessibility - LED Status indicators to indicate the relay ON/OFF status. - Mounting holes provided

Uses:Humidity detection, humidity sensors, humidity detection the working voltage 3.3V-5V the output form: DO digital switching outputs (0 and 1) and AO analog voltage output the comparator output signal is clean, good waveform, driving ability, more than 15mA a small PCB board size: 3.2cm x 1.4cm Module Features:  1, using high-quality HR202 humidity sensor;  2, the comparator output signal is clean, good waveform, driving ability, more than 15mA;  3, adjust the temperature distribution position detection threshold;  4, the working voltage 3.3V-5V;  5, the output form: DO digital switching outputs (0 and 1) and AO analog voltage output;  6, a fixed bolt holes for easy installation;  7, a small PCB board size: 3.2cm x 1.4cm;  8, using a wide voltage LM393 comparator.  Product wiring instructions:  1, VCC positive power supply 3.3-5V  2, GND power supply is negative  3, DO TTL switching signal output  4, AO small plates analog output (voltage signal)  Module for use  1, the humidity sensor module is sensitive to environmental humidity, generally used to detect ambient humidity;  2, by adjusting the potentiometer, for detecting the humidity can change the threshold (i.e. the humidity control), such as the need to control the ambient humidity of 60%,then the corresponding module is transferred to the green light and humidity environment, DO high power output when flat, humidity values below this setting, high output, the green light does not shine;  3, DO output can be directly connected to the microcontroller through the microcontroller to detect high and low, thereby detecting the humidity changes