Amplifier watts speaker

Amplifier and 100 watts speaker 2 nos, 8 inch woofer for sale.. amplifier need a minor service. price negotiable

Watt RMS MOSFET Stereo Power Amplifier Assembled High Quality Sound Effects Specifications for the Watt RMS MOSFET Stereo Power Amplifier Power rating of Watts RMS into 4 Ohms Two Channel Total 40 Mosfets caps uF Soft start, Speaker Protection Watts RMS Mono Bridge Connect otal Harmonic Distortion is typically %, Signal to Noise Ratio of - 122dB unweighted (20Hz to 20Khz) Assembled Time 12 Days

4way speaker capacity WATTS AMPLIFIER Fm, AUDIO IN, USB & MIC along with 2 8inch speaker super sound effect like home theater for just rs

IT'S A REAL POWERFUL STEREO AMPLIFIER KIT EVERYONE CAN MAKE YOU NEED A TRANSFORMER OF ABOUT 5AMP.12 VOLT THE POWER OUTPUT DEPENDING ON TRANSFORM IN 7AMP 12 TO 14 VOLT THE OUTPUT IS ABOUT 250 TO 300 RMS YOU NEED 10" TO 12" INCH SPEAKERS 100+ 100watt 2N3055 specifications: Polarity = NPN, IC = 15 Amp.(current) VCEO = 60 Volts, hFE = 20 (min), 70 (max) @ IC = 4 Amp, and VCE = 4 Volts, Safe Operating Area = 2.87 Amp × 40 V for 1 second pulse. fT = 2.5 MHz (min), RƟjc = 1.52 degree C/W, PTC = 115 Watts. NOTE: PRODUCTS MAYBE CHANGE DEPENDING ON STOCKS

IT'S A REAL POWERFUL STEREO AMPLIFIER KIT EVERYONE CAN MAKE YOU NEED A TRANSFORMER OF ABOUT 5AMP.12 VOLT THE POWER OUTPUT DEPENDING ON TRANSFORM IN 7AMP 12 TO 14 VOLT THE OUTPUT IS ABOUT 250 RMS YOU NEED 10" TO 12" INCH SPEAKERS 100+ 100watt 2N3055 specifications: Polarity = NPN, IC = 15 Amp.(current) VCEO = 60 Volts, hFE = 20 (min), 70 (max) @ IC = 4 Amp, and VCE = 4 Volts, Safe Operating Area = 2.87 Amp × 40 V for 1 second pulse. fT = 2.5 MHz (min), RƟjc = 1.52 degree C/W, PTC = 115 Watts. NOTE: PRODUCTS MAYBE CHANGE DEPENDING ON STOCKS

Harman kardon 5.1 speaker set brand sealed box package unused condition imported from Malaysia 1000watts suitable for all assemble 5.1 amplifier can use And 5.1 recevier 100 to 120 watts this speaker 8 ohm 4 inch woofer and 2" demo tweeter speaker double magnet shealed and subwoofer 10" inch 8 ohm 200 watts Speaker 86o87o99991

Marantz PM5005 Stereo Integrated Amplifier Featuring premium audiophile design at an affordable price, the Marantz PM5005 stereo integrated amplifier features all-analog circuitry from input to output, and delivers wide frequency response, high dynamic range along with true low impedance drive capability and is rated to handle both 8 ohms and 4 ohms speakers. Featuring current feedback power amplifier circuitry (a Marantz innovation), the power amplifier section also features pure discrete analog circuitry along with multiple high current discrete power output devices that are easily able to handle lower impedance loads and deliver high instantaneous peak current capability. Rated at 40 watts per channel into 8 ohms and 55 watts per channel into 4 ohms, the PM5005 features A and B speaker outputs, for two sets of stereo speakers, or for bi-wiring with compatible stereo speakers. The deluxe remote control provides discrete source input buttons, and includes additional buttons for direct control of the matching Marantz CD5005 player and Marantz Network Audio Players. Current Feedback Discrete Power Amplifier The PM5005 features a power amplifier section based on our renowned current feedback technology, a Marantz innovation that debuted on our very first power amplifier. High current discrete power output devices mounted on a generously-sized aluminum heat sink together provide high instantaneous peak current capability, and are easily able to handle dynamic bursts into lower impedance 4 ohm speaker loads (the current capacity for each amplifier channel is a substantial 16 amps). Wide Range of Connectivity Options   Veteran audiophiles and new generation music lovers both know that the sonic allure of vinyl records often can't be matched by digital audio sources, and the PM5005 includes multiple analog inputs including a MM (moving magnet) phono input. There are also dual recording inputs and outputs, along with a headphone amplifier jack on the front panel, and the high grade speaker connectors can accept multiple speaker cable termination types. The audio input and output jacks are all gold plated for maximum signal integrity. Source Direct Function To ensure the shortest signal path and the highest fidelity, the PM5005 features our Source Direct function, which bypasses the tone control and loudness control circuitry. Discrete amp Fully Discrete Volume Amplifier Circuit The volume amplifier circuit features fully discrete circuitry (no op amp chips in the signal path) for the widest bandwidth, lowest distortion, and highest dynamic range. Elegant Remote Control The elegant remote control includes additional function buttons that let you control a Marantz CD player and a Marantz Network Audio Player, for total system control with a single remote. Versatile Remote Control Options The PM5005 features remote control input and output jacks that let you hard wire the amplifier directly to a Marantz CD player, which in turn can be hard wired to a Marantz Network Audio Player. For example, you can place a Marantz CD player on an open shelf for easy access, and place the PM5005 and a Marantz Network Audio Player tucked away in a cabinet and hidden from view, and control all 3 units with a single remote, which helps to eliminate component clutter. 60+ Years of Audiophile Heritage Founded in 1953, Marantz has a long and rich history of designing audiophile components that have been embraced by music lovers and critical listeners around the world. Because Music Matters so much in our lives, the PM5005 carries on our long tradition of delivering a superlative music listening experience.

3 Year Limited Company Warranty (Read Warranty Terms) 7 to 10 Day Clear Shipping Time Is Requested For This Product. Kindly Proceed To Pay Only If Acceptable 7 to 10 Day Clear Shipping Time Is Requested For This Product. Kindly Proceed To Pay Only If Acceptable 7 to 10 Day Clear Shipping Time Is Requested For This Product. Kindly Proceed To Pay Only If Acceptable POLK AUDIO HTS-220 Home Cinema Pack 5.1 Ch. 3 Year Company Warranty (Requires Suitable Amplifier / AVR) 2 x Polk Audio TSx220B Bookshelf Front Speakers Bass-reflex (ported) design Frequency response: Hz (-3dB) Recommended amplifier power: watts 1" silk/polymer Dynamic Balance® dome tweeter 6-1/2" Dynamic Balance bi-laminate composite woofer with butyl rubber surround Impedance: 8-ohm Sensitivity: 90 dB Front-firing tuned port makes the speaker less sensitive to room placement and allows closer placement to a wall Gold-plated 5-way binding post terminals Black Woodgrain vinyl finish 8-3/8"W x "H x "D Weight: 13.6 lbs. (each) Warranty: 3 years 1 x Polk Audio TSx150C Center Channel Speaker Bass-reflex (ported) design Frequency response: Hz (-3dB) Recommended amplifier power: watts 1" silk/polymer Dynamic Balance® dome tweeter 5-1/4" Dynamic Balance bi-laminate composite woofers with butyl rubber surrounds Impedance: 8 ohms Sensitivity: 91 dB Gold-plated 5-way binding post terminals 20"W x 7"H x 8-1/2"D Warranty: 3 years 2 x Polk Audio OWM-3 Surround Speakers Acoustic suspension enclosure 1" silk dome tweeter 4-1/2" Dynamic Balance® polypropylene cone driver Capacitive Coupling Bass Technology for stronger low frequency response Frequency response Hz (-3dB) Handles watts 8-ohm impedance Sensitivity 89 dB 5-way gold-plated binding posts Includes removable base and black grille Multiple mounting options including on-wall, corner mounting, and table placement 7"W x 10"H x 4-1/8"D Warranty: 3 years 1 x Polk Audio PSW-110 Active Sub Woofer Bass-reflex (ported) enclosure 200-watt RMS dynamic power 10" front-firing driver Frequency response Hz Continuously variable Hz crossover Phase switch Auto on/off Line-level / LFE input Speaker-level input and output Black oak vinyl finish "W x "H x "D Warranty: 3 yr's Woofer Speaker, 1 yr Ele.Circuit (Requires Suitable Amplifier / AVR)   Welcome to our store! Thank you for viewing our products. If you have any questions don’t hesitate to contact us and  we will be happy to answer all your questions.  Please remember that all issues can be resolved without leaving a negative/neutral feedback or opening a dispute. If you have any issues with your order, have questions or comments contact us and we guarantee your issue will be resolved. Our goal is to ensure you have had a great shopping experience with us.  Sales Tax - For all shipments to Indian States and Union Territories, we are bound by law to collect the Sales Tax. To make your purchase as simple and easy as possible, please refer to the store policies listed below. After winning an item

3 Year Limited Company Warranty (Read Warranty Terms) 7 to 10 Day Clear Shipping Time Is Requested For This Product. Kindly Proceed To Pay Only If Acceptable 7 to 10 Day Clear Shipping Time Is Requested For This Product. Kindly Proceed To Pay Only If Acceptable 7 to 10 Day Clear Shipping Time Is Requested For This Product. Kindly Proceed To Pay Only If Acceptable POLK AUDIO TSx-220 Home Cinema Pack 3.1 Ch. 3 Year Company Warranty (Requires Suitable Amplifier / AVR) 2 x Polk Audio TSx220B Bookshelf Front Speakers Bass-reflex (ported) design Frequency response: Hz (-3dB) Recommended amplifier power: watts 1" silk/polymer Dynamic Balance® dome tweeter 6-1/2" Dynamic Balance bi-laminate composite woofer with butyl rubber surround Impedance: 8-ohm Sensitivity: 90 dB Front-firing tuned port makes the speaker less sensitive to room placement and allows closer placement to a wall Gold-plated 5-way binding post terminals Black Woodgrain vinyl finish 8-3/8"W x "H x "D Weight: 6.15 kg. (each) Warranty: 3 years 1 x Polk Audio TSx250C Center Channel Speaker Bass-reflex (ported) design Frequency response: dB) Recommended amplifier power: watts 1" silk/polymer Dynamic Balance® dome tweeter Two 6-1/2" Dynamic Balance bi-laminate composite woofers with butyl rubber surrounds impedance: 8-ohm Sensitivity: 91 dB Gold-plated 5-way binding post terminals Black woodgrain vinyl finish "W x 8"H x 9-3/8"D Weight: 8.4 kgs. Warranty: 3 years 1 x 12" Inch Polk Audio PSW-125 Active Sub Woofer Bass-reflex (ported) enclosure 300-watt RMS peak power amplifier 12" front-firing driver Frequency response Hz Continuously variable Hz crossover Phase switch Auto on/off Line-level/LFE input Speaker-level input and output "W x "H x "D Weight 18.2 kg. Color Black Warranty: 3 yr's Woofer Speaker, 1 yr Ele.Circuit (Requires Suitable Amplifier / AVR)   Welcome to our store! Thank you for viewing our products. If you have any questions don’t hesitate to contact us and  we will be happy to answer all your questions.  Please remember that all issues can be resolved without leaving a negative/neutral feedback or opening a dispute. If you have any issues with your order, have questions or comments contact us and we guarantee your issue will be resolved. Our goal is to ensure you have had a great shopping experience with us.  Sales Tax - For all shipments to Indian States and Union Territories, we are bound by law to collect the Sales Tax. To make your purchase as simple and easy as possible, please refer to the store policies listed below. After winning an item

This is a complete HI - FI set up consisting of:- Pair of original Sonodyne SX 606 SPEAKERS (120 watts) PMPO Sonodyne Uranus SQ 500 Equalizer Enkor EK Amplifier with usb and remote. This amplifier has been matched with this set of speakers and equalizer. This set has been matched with Branded and Local made speaker and tested with same range of 120 WATTS PMPO speaker and sound quality was excellent. Excellent sound quality and no distortion sound. No physical damage on Speaker or machines. This is ideal for out door and indoor party. Welcome for inspection.

Watt RMS MOSFET Stereo Hi Power Amplifier Assembled High Quality Sound Effects Specifications for the Watt RMS MOSFET Stereo H i Power Amplifier Power rating of Watts RMS into 4 Ohms Two Channel Powe r Supply -+96 volt Total 40 power Mosfet Transistors Speaker Protection and soft-start Stereo watts Bridge watts Mono Total Harmonic Distortion is typically %, Signal to Noise Ratio of - 122dB unweighted (10Hz to 20Khz) Assembled Time 10 Days

Grundig, a well-known German manufacturer of radios and other consumer electronic products, has recently entered the North American hi-fi market with the DX-, a compact and inexpensive two-way speaker system. It is distributed by Lextronix and sold by mail order through Willabee & Ward with a thirty-day return option for full refund if you are not satisfied (return shipping charges paid by them). The DX- is based on a 6.5-inch long-throw woofer in a vented enclosure, with a third-order (18-dB-per-octave) crossover at an unspecified frequency to a 1-inch soft-dome tweeter that incorporates magnetic-flu-id cooling and damping. The tweeter is protected by an automatically resetting device. The woofer's buty 1-rubber surround is said to extend the driver's life and to absorb excess energy at the outer edge of the cone. The DX-'s enclosure has beveled front edges and a removable black cloth grille. Gold-plated multiway binding-post input terminals are recessed into the rear of the cabinet. The woofer's vent opening is on the front of the cabinet, allowing the speaker to be placed close to a wall without interfering with its low-bass output. The drivers are magnetically shielded so that the speakers can be placed close to a video monitor or TV set without affecting the picture. They are also mounted flush with the front panel to minimize diffraction at their edges and are installed asymmetrically, with the tweeter located near a side of the panel and the woofer more conventionally in its center. Unlike almost any other speaker in its price range, the DX- is sold in mirror-image pairs. Grundig says that placing the tweeters close to the outside of the stereo pair produces a wider soundstage, whereas putting them at the inside (closer to each other) yields a deeper, more focused image. The company suggests that when the speakers are spaced 6 feet or less from each other, inward-facing placement is preferable. We placed the Grundig DX- speakers on stands about 30 inches off the floor and 9 feet apart. Their room responses were measured separately (with a sweeping warble tone) and then averaged to smooth out room interaction. A close-miked measurement of the woofer response was combined with the averaged room curve to generate a composite frequency-response plot. Although this curve is artificial, it is a reasonable representation of what the speaker can actually do in a real room, as contrasted with an anechoic response measurement. The variation was only +/-3.5 dB from 150 Hz to 20 kHz. At lower frequencies, the measured woofer response was actually better than what we heard, which was itself very good. There was no question that the system lived up to (and surpassed) its specified response of 50 Hz to 20 kHz. - See more at: http://www.hifi-review.com/-grundig-dx-.html#sthas h.qd3hrGrs.dpufThe smoothness of the DX-'s response was further evidenced by quasi-anechoic MLS measurements at 1 and 2 meters from the speaker, which indicated a +/-4-dB variation from 300 Hz to 20 kHz. The speaker's horizontal dispersion was good, exhibiting less than 5 dB change in level over a +/-45-degree angle up to 10 kHz and less than 10 dB at 20 kHz. System impedance never went below 5 ohms, typically measuring between 6 and 15 ohms and justifying the speaker's 8-ohm rating. Sensitivity, specified as 89 dB sound-pressure level (SPL) at 1 meter with a 2.83-volt input, measured somewhat higher at 92 dB. With a 2.25-volt input, corresponding to our reference measurement level of 90 dB SPL, the woofer distortion was between 1 and 3 percent from 50 Hz to 2 kHz, rising rapidly to about 10 percent at 40 Hz. In single-cycle pulse power tests, the DX- absorbed all the power we could pump into it at 1 and 10 kHz, with our amplifier clipping at 800 to watts, respectively, into the impedances at those frequencies. At 100 Hz, the woofer cone bottomed audibly with an input of about 90 watts. Since this is a rather efficient speaker, it can play quite loud without damage to itself or listeners' sensibilities. It is usually difficult to describe the sound of a speaker to someone who has never heard it. The best I can do is to say that the DX- does not, in the slightest, sound like a little black box selling for $300 a pair. I guarantee that anyone hearing it blindfolded would not come close to guessing its price. When I first set the Grundig speakers up, I had on hand another pair of excellent speakers selling for several times their price and correspondingly larger and heavier than they are. In A/B comparisons, I frequently had to look at my comparator switches to be sure which pair I was hearing. The chief exception was when I was playing music with substantial bass content - good as the DX- is, it cannot work miracles! In short, the DX- is one of the most satisfying small speakers I have heard in some time. There are a few really musical small speakers carrying brand names better known in the hi-fi world than that of Grundig (and usually more expensive). This little black box belongs in that group and deserves your serious consideration. - See more at: http://www.hifi-review.com/-grundig-dx-.html#sthas h.qd3hrGrs.dpuf

20 Watts RMS Output ·          8″ Dual Cone full range Speaker ·          Built-in rechargeable Battery ·          Digital Vocal Echo ·          3-Mic inputs (low impedance)/AUX/MP3 Player with SD/USB inputs ·          Line Out & External Speaker output ·          Full functional remote for MP3 player ·          FM with Antenna ·          Separate BASS/TREBLE controls ·          Separate ECHO effects with Echo depth and Echo time controls ·          Battery level indicator – FULL/HIGH/MEDIUM/LOW Battery level indicators ·          Compact size, Moulded grill and all plywood rexine finish ·          Handle provided for ease of carrying ·          Accessories included: AC Lead, Built-in Rechargeable Battery, Remote for MP3 Player, FM Antenna wire       POWER SUPPLY AC 220V 50Hz/ 12V BUILTIN RECHARGEABLE BATTERY POWER OUTPUT 20 Watts RMS SPEAKER TYPE 8″ Full Range Speaker MIC INPUTS 3 x MIC Inputs with Digital Vocal Echo, Aux & MP3 Player with SD/ USB Inputs TONE CONTROLS Bass/ Treble +-10dB OUTPUTS Line Out & External Speaker Out ECHO Echo effects with Echo Depth/ Echo Time controls DIMENSIONS 280W x 165D x 340H mm WEIGHT Kg

Stereo Sub woofer Speaker System watts Wood Waterpro of NewWood 4 * 12" Sub-Woofer  4 * 3" magnet Philips Tweeter  Box Height == 37 inch Box Width == inch Box Depth== inch Excellent sound best result low freq. Minimum watts RMS Amplifier require call come and pickup

These are a pair of Technics Vintage Three Way Speakers. For super acoustic sound experience Technics has used best wooden material. Very warm sound with all details. Great look and feel. Cross Over Frequency response of Hz -Hz -Sensitivity: 92dB / 1W / 1m-/ Rated - 50Wattas RMS DIN & 75 Watts Music - It will match with any brand of Amplifier as it as nominal impedance- 8 Ohms. Superb Sound Effect. As on today, it is easily handled 50Watts RMS- Din and 75Watts Music. Woofer -8” Dimensions [H x W x D]: 600mm x 320mm x 200mm No Bargain Please. I have purchased this Vintage Made In Japan Speaker (Second hand) before 5 Years and there is no problem till date and quality is too.. Good. After all it’s from TECHNICS It is difficult to find transistor base (Not Cheap IC base)Technics, Pioneer or Sansui vintage amplifier but it is very very difficult to find vintage speaker. Shipping Possible Made In Japan

Good quality F&D Brand Amplifier for sale. 800 Watts PMPO, Two speakers can be attached Bass Treble Control and one Base Speaker output. Good sound output.

Condition as new, Remote not available. The Marantz PM7200 Stereo Integrated Amplifier offers music enthusiasts uncompromising audiophile sound quality and superior flexibility of operation. It delivers 2 x 95 Watts (RMS into 8 Ohms), rising to 155 watts with 4 Ohm speakers. A single push-pull amplifier, symmetrical circuitry withindependent heat sink, anti-resonant, metal front panel and hand selected customized components including HDAM, assuring an extremely dynamic sound reproduction with accurate tonal and image balance. It offers Class A operation for distortion-free sound at low volume levels and gold-plated in- and output terminals. With full system remote control operation, the PM7200 is the ideal center piece for a true high-end music system. 95 watts per channel power output (into 8 ohms) 155 watts per channel (into 4 ohms) 25 watts pure class A operation HDAM (High Definition Amplifier Module) fully discrete copper-shielded output stage Premium-quality parts and construction for superb sound quality Seven source inputs including moving magnet (MM) phono input Remote control operation including volume adjustment

Harman Kardon Omni 20 Bluthooth Speaker Brand new Showroom conditions Specification wireless system couldn't be simpler. Simply join one HK Omni unit to your Wi-Fi network in the usual way and then set all other units up at the touch of a button. Once you've set up your components, taking control is easy, thanks to the dedicated Harman Kardon control app. Available for Apple iOS or Android. Where the Harman Kardon Omni system stands out from many of its competitors is in its ability to stream High Resolution music files. Stream many file types at up to 24 bit/96kHz quality for a sound that's superior to CD. The HK Omni system is highly flexible and allows the music to follow you from room to room. With the Omni 10 and 20 it's possible to configure the speakers as stereo pairs. Another feature missing from many rivals is the inclusion of Bluetooth streaming. Simply pair with your Bluetooth device, such as Smartphone, tablet or even PC/Mac and then re-stream the music across all the other Omni speakers. Alternatively, use the 3.5mm AUX input fitted to all three Omni devices to not just playback sound on the individual speaker but also stream the signal across all other connected Omni devices. Boasting two-way, stereo speakers and a 60 watts amplifier, the HK Omni 20 is no shrinking violet! The larger Omni 20 has little trouble in filling bigger rooms with smooth, powerful sound. From the deep, controlled bass right up to the bright, articulate treble, the Omni 20 impresses throughout the frequency range. From the Manufacturer Every Room Together in Wireless Harmony Enjoy beautiful sound from room to room with the touch of a button. With exceptional sound quality, simple wireless setup and complete app control, your music never stops. What is the Harman Kardon Wireless HD Audio System? The Harman Kardon Wireless HD Audio System is a suite of audio products designed to wirelessly fill your home with beautiful, high-definition sound. Start with any combination of Omni 10, Omni 20, or Adapt units and expand your system at any time to create seamless multi-room audio using your home wireless network and the Harman Kardon Controller App. How Does the System Work? Each speaker and adaptor wirelessly connects to your home Wi-Fi network. Using your phone or tablet and the Harman Kardon Controller App (available for iOS and Android), you can stream all your music through any speaker or any room in your home. The Link button on the top of every Omni speaker and Adapt lets you take your music from room to room with a single touch. If you want to fill your entire home with sound, just press and hold the Link button to activate Party Mode to play the same song throughout every speaker and room in your home. Will the System Work with my Existing Hi-Fi Equipment? Yes. The entire system wirelessly connects to your home Wi-Fi network with just one power cable needed for each speaker. Many other systems need to be wired to your router, or require an additional Bridge unit. This system uses a special Firecast protocol, which allows your existing router to wirelessly send HD audio to every speaker. No additional equipment is needed. Plug in to power up speaker Download the Harman Kardon Controller App Follow instructions in app Any song. Any source. Any room. Wirelessly Omni 10 Elegantly designed for crystal clear quality in smaller rooms with the touch of a button. Start with one Omni 10 for rooms around 10 sqm, and add another for true 2.0 stereo sound in rooms up to 15 sqm. Omni 20 A more powerful speaker for superior sound and performance in larger rooms. Use one Omni 20 in rooms up to 16 sqm, and add another for crystal clear 2.0 stereo sound in bigger rooms. Adapt Already have speakers? Use the Adapt to transform your existing system into a wireless one and stream your music in HD quality with the touch of a button. Features & details Wireless audio in every room. Seamlessly stream your favorite music to all Harman Kardon wireless HD audio products in your house Listen to different music in each room. Stream your favorite cla

Product Description: The Laney LX12 is a great little amp for practice.  Featuring 10 watts output, twin channels,  Global EQ and a 1x6" custom speaker.  And as you can see, it looks the business too ! Specification: Power RMS 10 Watts Inputs 1x Jack Channels 1 with switchable gain Equalisation Global Bass, Mid and Treble Reverb No Line Out No Footswitch No Speaker connections No FX Loop(s) No Drivers 1x6" Custom Driver Cabinet Design Black metal corners, gloss metal grille and rubber feet Master Effects Level Controls No Effects No Headphone Socket Yes CD Input Yes (Stereo jack) Kick Proof Metal Grill Yes Weight 4.2 Kg Dimensions Width 282 x Height 293 x Depth 173

Sonodye SX 606 pair of speakers 120 Watts PMPO is available in excellent condition. Speaker has never been repaired or recoiled. Excellent sound clarity as it was always used at home. No distorting sound, or cracked noise. This pair of speakers have been tested with other Equalizer and Amplifier and sound quality is really excellent. No damage on the outer wooden box. Only slight scratches and color has faded slightly. Text me on whatsapp or call.

Yamaha hi-end amplifier with original remote. you may use it as a pre amplifier also. gr8 look with prefect working. Sirius persons plz call on 9210. 27. 2811. Yamaha DSP-A2070 Audio Video Amplifier (1992-96) Specifications Power output: 80 watts per channel into 8Ω (stereo) Surround output: 80W (front), 80W (center), 25W (rear) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.005% Input sensitivity: 2.5mV (MM), 150mV (line) Signal to noise ratio: 96dB (line) Output: 150mV (line) Speaker load impedance: 4Ω to 16Ω Video Connections: composite, SVHS Dimensions: 435 x 170 x 468.5mm Weight: 21kg Accessories: remote control 1992 Key words:- Onkyo, denon, MARANTZ, Yamaha, Bose, Sony, Polk audio, nad, Harman kardon, Jbl, infinity, jamo, morden shot, Technics, Pioneer, Elac, B&W, B&O,.